Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › from 2017.12
RM33A0E _51 Engine / Hybrid System _065341 A25A-FKS ENGINE CONTROL _0344647 SFI SYSTEM(w/o Canister Pump Module) C

A25A-FKS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P21CF13  Cylinder 1 Injector "B" Circuit Open  P21D013  Cylinder 2 Injector "B" Circuit Open  P21D113  Cylinder 3 Injector "B" Circuit Open  P21D213  Cylinder 4 Injector "B" Circuit Open  


DESCRIPTION

The D-4S system has two injection systems. One is an in-cylinder direct injection system that directly injects pressurized fuel into the combustion chamber. The other is an intake port injection system. The ECM determines the percentage of direct injection and port injection necessary in accordance with the engine speed and load.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P21CF13 Cylinder 1 Injector "B" Circuit Open Open or short in port fuel injector assembly (1 trip detection logic).
·

Open or short in port fuel injector assembly circuit

·

Port fuel injector assembly

·

ECM


Comes on DTC stored SAE Code: P21CF
P21D013 Cylinder 2 Injector "B" Circuit Open Open or short in port fuel injector assembly (1 trip detection logic).
·

Open or short in port fuel injector assembly circuit

·

Port fuel injector assembly

·

ECM


Comes on DTC stored SAE Code: P21D0
P21D113 Cylinder 3 Injector "B" Circuit Open Open or short in port fuel injector assembly (1 trip detection logic).
·

Open or short in port fuel injector assembly circuit

·

Port fuel injector assembly

·

ECM


Comes on DTC stored SAE Code: P21D1
P21D213 Cylinder 4 Injector "B" Circuit Open Open or short in port fuel injector assembly (1 trip detection logic).
·

Open or short in port fuel injector assembly circuit

·

Port fuel injector assembly

·

ECM


Comes on DTC stored SAE Code: P21D2

MONITOR DESCRIPTION

The ECM monitors the injection control of the port fuel injector assemblies. If a malfunction is detected in a port fuel injector assembly circuit, the ECM cancels the injection control for the corresponding cylinder, illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components Port fuel injector assembly (cylinder 1 to 4)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Start the engine.

7.

Idle the engine for 3 minutes or more [A].

8.

Turn the GTS on.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [B].

10.

Read the DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P21CF13, P21D013, P21D113 or P21D213.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [A] through [B] again.




WIRING DIAGRAM

A412227E01
0.573,6.031 1.135,6.344 0.563,0.313 10 false Battery 0.406,5.052 1.479,5.25 1.073,0.198 10 false FL MAIN 1.344,1.583 2.417,1.781 1.073,0.198 10 false IG2 NO. 1 0.51,1.01 1.583,1.208 1.073,0.198 10 false IG2-MAIN 2.302,1.01 3.375,1.208 1.073,0.198 10 false INJ 1.375,4.396 2.448,4.594 1.073,0.198 10 false K62 1.365,4.552 3.198,4.917 1.833,0.365 10 false Certification ECU (Smart Key ECU Assembly) 1.833,3.865 2.906,4.063 1.073,0.198 10 false IG1D 2.25,3.74 3.323,3.938 1.073,0.198 10 false 17 6.281,6.073 6.844,6.385 0.563,0.313 10 false ECM 1.208,0.74 2.281,0.938 1.073,0.198 10 false 5 1.208,1.135 2.281,1.333 1.073,0.198 10 false 2 2,0.74 3.073,0.938 1.073,0.198 10 false 3 2,1.135 3.073,1.333 1.073,0.198 10 false 1 5.542,4.688 6.615,4.885 1.073,0.198 10 false 10 5.5,4.885 6.573,5.083 1.073,0.198 10 false A24 5.844,4.781 6.917,4.979 1.073,0.198 10 false E1 5.5,3.885 6.573,4.083 1.073,0.198 10 false C57 5.5,2.865 6.573,3.063 1.073,0.198 10 false C57 5.49,1.865 6.563,2.063 1.073,0.198 10 false C57 5.5,0.865 6.573,1.063 1.073,0.198 10 false C57 5.854,3.76 6.927,3.958 1.073,0.198 10 false #40 5.854,2.75 6.927,2.948 1.073,0.198 10 false #30 5.844,1.75 6.917,1.948 1.073,0.198 10 false #20 5.854,0.74 6.927,0.938 1.073,0.198 10 false #10 6.688,2.885 6.99,3.219 0.302,0.333 10 false IC 5.542,3.688 6.615,3.885 1.073,0.198 10 false 73 5.542,2.667 6.615,2.865 1.073,0.198 10 false 74 5.552,1.677 6.625,1.875 1.073,0.198 10 false 75 5.542,0.667 6.615,0.865 1.073,0.198 10 false 76 3.646,1.104 5.396,1.479 1.75,0.375 10 false Port Fuel Injector Assembly (No. 1 Cylinder) 3.375,1.104 4.448,1.302 1.073,0.198 10 false F2 3.375,2.094 4.448,2.292 1.073,0.198 10 false F5 3.646,3.104 5.396,3.479 1.75,0.375 10 false Port Fuel Injector Assembly (No. 3 Cylinder) 3.375,3.104 4.448,3.302 1.073,0.198 10 false F8 3.646,4.115 5.396,4.49 1.75,0.375 10 false Port Fuel Injector Assembly (No. 4 Cylinder) 3.354,4.115 4.427,4.313 1.073,0.198 10 false F11 3.802,0.729 4.875,0.927 1.073,0.198 10 false 1 3.813,1.719 4.885,1.917 1.073,0.198 10 false 1 3.823,2.729 4.896,2.927 1.073,0.198 10 false 1 3.833,3.76 4.948,4.042 1.115,0.281 10 false 1 4.854,0.74 5.719,1.083 0.865,0.344 10 false 2 4.844,1.74 5.708,2.083 0.865,0.344 10 false 2 3.646,2.094 5.396,2.469 1.75,0.375 10 false Port Fuel Injector Assembly (No. 2 Cylinder) 4.854,2.75 5.719,3.094 0.865,0.344 10 false 2 4.865,3.75 5.729,4.094 0.865,0.344 10 false 2 4.531,0.74 5.604,0.938 1.073,0.198 10 false #10 4.521,1.74 5.594,1.938 1.073,0.198 10 false #20 4.521,2.75 5.594,2.948 1.073,0.198 10 false #30 4.531,3.75 5.604,3.948 1.073,0.198 10 false #40 4.021,0.74 5.094,0.938 1.073,0.198 10 false #1 4.021,1.74 5.094,1.938 1.073,0.198 10 false #2 4.01,2.75 5.083,2.948 1.073,0.198 10 false #3 4.021,3.75 5.094,3.948 1.073,0.198 10 false #4

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTCS OUTPUT (IN ADDITION TO DTC P21CF13, P21D013, P21D113 OR P21D213)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P21CF13, P21D013, P21D113 or P21D213 is output A
DTC P21CF13, P21D013, P21D113 and P21D213 are output B




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PORT FUEL INJECTOR ASSEMBLY)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 NO. 1 RELAY - PORT FUEL INJECTOR ASSEMBLY)

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PORT FUEL INJECTOR ASSEMBLY)
A412228C01
0.115,0.615 0.531,0.854 0.417,0.24 0.635,0.615 1.052,0.854 0.417,0.24 0.115,0.927 0.531,1.167 0.417,0.24 0.635,0.927 1.052,1.167 0.417,0.24 1.094,1.365 1.583,1.135 true 0.24,0.229 0.552,0.542 0.313,0.313 10 false *a 0.25,0.656 0.563,0.969 0.313,0.313 10 false F2 0.781,0.667 1.094,0.979 0.313,0.313 10 false F5 0.26,0.958 0.573,1.271 0.313,0.313 10 false F8 0.74,0.969 1.052,1.281 0.313,0.313 10 false F11 0.771,1.281 1.083,1.594 0.313,0.313 10 false #1*b 0.771,1.469 1.083,1.781 0.313,0.313 10 false #2*c 0.771,1.667 1.083,1.979 0.313,0.313 10 false #3*d 0.771,1.865 1.208,2.104 0.438,0.24 10 false #4*e
*a Front view of wire harness connector
(to Port Fuel Injector Assembly)
*b No. 1 Cylinder
*c No. 2 Cylinder
*d No. 3 Cylinder
*e No. 4 Cylinder


a.

Disconnect the port fuel injector assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below

Standard Voltage:
Tester Connection Condition Specified Condition
F2-1 (#1) - Body ground Ignition switch ON 11 to 14 V
F5-1 (#2) - Body ground Ignition switch ON 11 to 14 V
F8-1 (#3) - Body ground Ignition switch ON 11 to 14 V
F11-1 (#4) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PORT FUEL INJECTOR ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 NO. 1 RELAY - PORT FUEL INJECTOR ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (PORT FUEL INJECTOR ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the port fuel injector assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F2-2 (#10) - C57-76 (#10) Always Below 1 Ω
F5-2 (#20) - C57-75 (#20) Always Below 1 Ω
F8-2 (#30) - C57-74 (#30) Always Below 1 Ω
F11-2 (#40) - C57-73 (#40) Always Below 1 Ω
F2-2 (#10) or C57-76 (#10) - Body ground and other terminals Always 10 kΩ or higher
F5-2 (#20) or C57-75 (#20) - Body ground and other terminals Always 10 kΩ or higher
F8-2 (#30) or C57-74 (#30) - Body ground and other terminals Always 10 kΩ or higher
F11-2 (#40) or C57-73 (#40) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT PORT FUEL INJECTOR ASSEMBLY (RESISTANCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT PORT FUEL INJECTOR ASSEMBLY (RESISTANCE)
a.

Inspect the port fuel injector assembly.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL INJECTOR (for Port Injection)>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the port fuel injector assembly.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG