The rear window shade assembly operates according to operation signals from the combination meter assembly or rear sunshade switch (cooler control switch assembly)*.
*: w/ Cooler Control Switch Assembly
Inspect the fuses for circuits related to this system before performing the following procedure.
Check rear sunshade manual operation.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR SUNSHADE SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| The rear sunshade does not operate with combination meter assembly operation. | A |
| The rear sunshade does not operate with rear sunshade switch (cooler control switch assembly) operation. (w/ Cooler Control Switch Assembly) | B |
| The rear sunshade does not operate with combination meter assembly and rear sunshade switch (cooler control switch assembly) operation. (w/ Cooler Control Switch Assembly) | C |
A
B
C
| *a | Component with harness connected
(Combination Meter Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K21-22 (ECU) - Body ground | Rear window shade assembly not operating | 5.5 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the R64 rear window shade assembly connector.
Disconnect the K21 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R64-5 (SW) - K21-22 (ECU) | Always | Below 1 Ω |
| R64-5 (SW) or K21-22 (ECU) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Rear Sunshade Switch (Cooler Control Switch Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z1-4 (ECU) - Body ground | Rear window shade assembly not operating | 5.5 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Z1 rear sunshade switch (cooler control switch assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z1-10 (+IG) - Body ground | Ignition switch off | Below 1 V |
| Z1-10 (+IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z1-16 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the R64 rear window shade assembly connector.
Disconnect the Z1 rear sunshade switch (cooler control switch assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R64-4 (RSW) - Z1-4 (ECU) | Always | Below 1 Ω |
| R64-4 (RSW) or Z1-4 (ECU) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the R64 rear window shade assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R64-8 (B) - Body ground | Always | 11 to 14 V |
| R64-7 (IG) - Body ground | Ignition switch off | Below 1 V |
| R64-7 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R64-1 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG