Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Entry and Start System) › 2017.12–2022.01
RM33A0E _58 Vehicle Interior _065378 DOOR LOCK _0329091 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System)  Only Wireless Control Function is Inoperative  


DESCRIPTION

The door control receiver receives signals from the door control transmitter module set sub-assembly and sends these signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher signals to the combination meter assembly.

WIRING DIAGRAM

B479754E04
3.063,0.688 4.896,0.885 1.833,0.198 10 false from Battery 1.854,0.854 3.844,1.052 1.99,0.198 10 false ECU-DCC NO. 2 1.51,0.688 1.823,0.885 0.313,0.198 10 false +B 1.813,0.542 2.458,0.802 0.646,0.26 10 false 7*1, 5*2 1.396,1.375 1.854,1.573 0.458,0.198 10 false RDA 1.823,1.396 2.573,1.74 0.75,0.344 10 false 4*1, 2*2 1.396,2.573 1.854,2.771 0.458,0.198 10 false PRG 1.833,2.594 2.615,2.979 0.781,0.385 10 false 5*1, 3*2 0.573,2.135 0.885,2.333 0.313,0.198 10 false IC 1.396,3.792 1.854,3.99 0.458,0.198 10 false GND 1.823,3.677 2.563,4.01 0.74,0.333 10 false 12*1, 1*2 3.771,3.688 3.927,3.885 0.156,0.198 10 false 1 2.813,3.688 2.969,3.885 0.156,0.198 10 false 2 4.01,3.677 4.323,3.875 0.313,0.198 10 false 41 5.073,3.604 5.229,3.802 0.156,0.198 10 false 3 0.083,4.427 0.875,4.615 0.792,0.188 10 false R120*1 0.073,4.573 2.635,5.219 2.563,0.646 10 false Door Control and Tire Pressure Monitoring System Receiver Assembly 2.708,4.198 3.167,4.396 0.458,0.198 10 false K31 2.708,4.354 4.177,5.219 1.469,0.865 10 false Unlock Warning Switch Assembly 4.219,4.208 4.531,4.406 0.313,0.198 10 false 3A 4.229,4.354 5.313,5.26 1.083,0.906 10 false Instrument Panel Junction Block Assembly 5.385,4.448 7.042,5.323 1.656,0.875 10 false Main Body ECU (Multiplex Network Body ECU) 5.01,3.792 5.323,3.99 0.313,0.198 10 false MB 5.354,3.792 5.813,3.99 0.458,0.198 10 false KSW 5.354,2.594 5.813,2.792 0.458,0.198 10 false PRG 5,2.708 5.458,2.906 0.458,0.198 10 false K53 5.031,2.521 5.344,2.719 0.313,0.198 10 false 11 5,1.521 5.458,1.719 0.458,0.198 10 false K53 5.031,1.333 5.344,1.531 0.313,0.198 10 false 10 5.344,1.396 5.802,1.594 0.458,0.198 10 false RDA 5.75,0.792 6.063,0.99 0.313,0.198 10 false +B 6.406,2.094 6.719,2.292 0.313,0.198 10 false IC 0.063,5.229 1.229,5.458 1.167,0.229 10 false R16*2 0.063,5.49 1.948,5.781 1.885,0.292 10 false Door Control Receiver 2.281,5.271 4.167,5.563 1.885,0.292 10 false *1: for 12 Pin Type 3.604,5.281 5.49,5.573 1.885,0.292 10 false *2: for 5 Pin Type

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, wireless function performance may be affected.

·

When replacing the door control and tire pressure monitoring system receiver assembly, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.*

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION

*: for 12 Pin Type


·

If the door control and tire pressure monitoring system receiver assembly has been replaced, it is necessary to perform initialization (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs to the door control and tire pressure monitoring system receiver assembly.*

*: for 12 Pin Type


·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

Check the power door lock operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


OK:

Locked doors unlock.


Result:
Proceed to
OK
NG



OK

2.CHECK KEY REMINDER WARNING SYSTEM

NG

2.CHECK KEY REMINDER WARNING SYSTEM
a.

Check that the key reminder warning buzzer operates properly.

Click hereVehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>OPERATION CHECK


OK:

Key reminder warning buzzer operates properly.


Result:
Proceed to
OK
NG



OK

3.CHECK DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY

NG

3.CHECK DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY
a.

When a known good registered door control transmitter module set sub-assembly is used, check that the wireless functions operate properly.


Result:
Result Proceed to
Wireless door lock/unlock function operates properly with a known good door control transmitter module set sub-assembly A
Wireless door lock/unlock function does not operate B



A

4.CHECK TRANSMITTER BATTERY (VOLTAGE)

B

5.CHECK WAVE ENVIRONMENT
4.CHECK TRANSMITTER BATTERY (VOLTAGE)

Result:
Proceed to
OK
NG



OK

REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY

NG

5.CHECK WAVE ENVIRONMENT
a.

Bring the door control transmitter module set sub-assembly near the door control receiver, and perform wireless operation check.

HINT:
·

When the door control transmitter module set assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.




OK:

Wireless functions operate properly.


Result:
Proceed to
OK
NG



OK

END (AFFECTED BY WAVE INTERFERENCE)

NG

6.CHECK SELF-DIAGNOSTIC MODE
6.CHECK SELF-DIAGNOSTIC MODE


Result:
Result Proceed to
Normal pattern (wireless door lock buzzer output pattern) is output A
Unmatching recognition code is output B
No diagnostic output C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

7.CHECK REGISTER RECOGNITION CODE

C

8.CHECK DOOR CONTROL RECEIVER (RESPONSE)
7.CHECK REGISTER RECOGNITION CODE
a.

Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Entry and Start System)>REGISTRATION


OK:

Recognition code can be registered.


Result:
Proceed to
OK
NG



OK

END (GO TO OPERATION CHECK)

NG

12.REPLACE DOOR CONTROL RECEIVER
8.CHECK DOOR CONTROL RECEIVER (RESPONSE)
a.

Prepare a door control transmitter module set sub-assembly from another vehicle.


b.

Press and hold a door control transmitter module set sub-assembly switch.


c.

Check that an unmatching recognition code is output.


OK:

Unmatching recognition code is output.


Result:
Proceed to
OK
NG



OK

REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY

NG

9.CHECK HARNESS AND CONNECTOR (POWER SOURCE AND BODY GROUND)
9.CHECK HARNESS AND CONNECTOR (POWER SOURCE AND BODY GROUND)
a.
B288160C31
1.531,0.458 1.906,0.677 0.375,0.219 1.521,2.771 1.896,2.99 0.375,0.219 2.365,1.896 2.031,1.896 2.031,1.896 2.031,1.479 false 1,1.875 1.406,1.875 1.406,1.875 1.406,1.469 false 2.083,3.74 2.417,3.74 false 1.021,3.75 1.354,3.75 false 0.667,0.552 0.979,0.75 0.313,0.198 10 false *a 1.594,2.792 2.052,2.99 0.458,0.198 10 false R16 1.563,0.49 2.021,0.688 0.458,0.198 10 false R120 0.781,2.885 1.094,3.083 0.313,0.198 10 false *a 0.333,0.281 0.729,0.573 0.396,0.292 10 false *A 0.375,2.573 0.688,2.771 0.313,0.198 10 false *B 0.771,1.792 1.094,1.99 0.323,0.198 10 false +B 2.417,1.813 2.875,2.01 0.458,0.198 10 false GND 0.698,3.667 1.156,3.865 0.458,0.198 10 false GND 2.479,3.667 2.938,3.865 0.458,0.198 10 false +B
*A for 12 Pin Type
*B for 5 Pin Type
*a Front view of wire harness connector
(to Door Control Receiver)


Disconnect the R120*1 or R16*2 door control receiver connector.

*1: for 12 Pin Type

*2: for 5 Pin Type



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R120-12 (GND) - Body ground*1 Always Below 1 Ω
R16-1 (GND) - Body ground*2 Always Below 1 Ω


*1: for 12 Pin Type

*2: for 5 Pin Type



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R120-7 (+B) - Body ground*1 Always 11 to 14 V
R16-5 (+B) - Body ground*2 Always 11 to 14 V


*1: for 12 Pin Type

*2: for 5 Pin Type



Result:
Proceed to
OK
NG



OK

10.CHECK DOOR CONTROL RECEIVER (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK DOOR CONTROL RECEIVER (OUTPUT)
a.

Reconnect the R120*1 or R16*2 door control receiver connector.

*1: for 12 Pin Type

*2: for 5 Pin Type



b.
B354352C07
1.458,0.323 1.865,0.594 0.406,0.271 1.458,2.563 1.865,2.833 0.406,0.271 2.104,4.052 1.865,4.052 1.865,4.052 1.865,3.417 false 1.635,1.188 1.635,1.031 1.635,1.031 2.458,1.031 false 0.635,0.552 0.948,0.75 0.313,0.198 10 false *a 0.24,0.177 0.615,0.448 0.375,0.271 10 false *A 0.365,2.448 0.677,2.646 0.313,0.198 10 false *B 0.646,2.76 0.958,2.958 0.313,0.198 10 false *a 1.542,2.604 1.917,2.802 0.375,0.198 10 false R16 1.51,0.375 2.021,0.542 0.51,0.167 10 false R120 2.5,0.948 2.875,1.156 0.375,0.208 10 false RDA 2.156,3.969 2.531,4.177 0.375,0.208 10 false RDA
*A for 12 Pin Type
*B for 5 Pin Type
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R120-4 (RDA) - Body ground*1
Procedure:
1.

Remove key from ignition key cylinder

2.

Close all doors

3.

Press lock or unlock switch of door control transmitter module set sub-assembly


11 to 14 V → pulse generation
R16-2 (RDA) - Body ground*2


*1: for 12 Pin Type

*2: for 5 Pin Type



Result:
Result Proceed to
OK A
NG (for 12 Pin Type) B
NG (for 5 Pin Type) C



A

11.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - DOOR CONTROL RECEIVER)

B

C

REPLACE DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - DOOR CONTROL RECEIVER)
a.

Disconnect the K53 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the R120*1 or R16*2 door control receiver connector.

*1: for 12 Pin Type

*2: for 5 Pin Type



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R120-4 (RDA) - K53-10 (RDA)*1 Always Below 1 Ω
R16-2 (RDA) - K53-10 (RDA)*2 Always Below 1 Ω
R120-5 (PRG) - K53-11 (PRG)*1 Always Below 1 Ω
R16-3 (PRG) - K53-11 (PRG)*2 Always Below 1 Ω
R120-4 (RDA) or K53-10 (RDA) - Other terminals and body ground*1 Always 10 kΩ or higher
R16-2 (RDA) or K53-10 (RDA) - Other terminals and body ground*2 Always 10 kΩ or higher
R120-5 (PRG) or K53-11 (PRG) - Other terminals and body ground*1 Always 10 kΩ or higher
R16-3 (PRG) or K53-11 (PRG) - Other terminals and body ground*2 Always 10 kΩ or higher


*1: for 12 Pin Type

*2: for 5 Pin Type



Result:
Proceed to
OK
NG



OK

12.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE DOOR CONTROL RECEIVER
a.

Temporarily replace the door control receiver with a new or known good one.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER (w/o Tire Pressure Warning System)>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.REGISTER RECOGNITION CODE
13.REGISTER RECOGNITION CODE

Result:
Proceed to
NEXT



NEXT

14.CHECK DOOR CONTROL RECEIVER (OPERATION)
14.CHECK DOOR CONTROL RECEIVER (OPERATION)
a.

Check that the doors can be locked and unlocked by the door control transmitter module set sub-assembly lock and unlock switches.


OK:

Doors can be locked and unlocked by the door control transmitter module set sub-assembly.


Result:
Proceed to
OK
NG



OK

END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)