The key reminder warning buzzer sounds when the driver door is opened while the ignition switch is off or ACC. The key reminder warning buzzer is activated when the main body ECU (multiplex network body ECU) sends an unlock warning switch signal and driver door courtesy light switch signal to the combination meter assembly via CAN communication.
for LHD
for RHD
The key reminder warning system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the key reminder warning system after confirming that the communication systems are functioning properly.
Click hereVehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Buzzer Operation (800Hz, Vol L, W/ Damping) | Combination meter buzzer
·
Frequency: 800Hz ·
Volume: Large ·
Fading tone |
ON | - |
| Tester Display |
|---|
| Buzzer Operation (800Hz, Vol L, W/ Damping) |
| Result | Proceed to |
|---|---|
| Combination meter buzzer sounds | A |
| Combination meter buzzer does not sound | B |
A
B
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Courtesy SW | Front door courtesy light switch assembly (for RH) signal*2 | OFF or ON | OFF: Front door RH closed
ON: Front door RH open |
- |
| FL Door Courtesy SW | Front door courtesy light switch assembly (for LH) signal | OFF or ON | OFF: Front door LH closed
ON: Front door LH open |
- |
*1: for LHD
*2: for RHD
| Tester Display |
|---|
| FR Door Courtesy SW |
| FL Door Courtesy SW |
The GTS indicates ON or OFF according to the driver door conditions shown in the table.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Key Unlock Warning SW | Unlock warning switch signal | OFF or ON | OFF: No key in ignition key cylinder
ON: Key in ignition key cylinder |
- |
| Tester Display |
|---|
| Key Unlock Warning SW |
The GTS indicates ON or OFF according to whether the key is in the ignition key cylinder.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the unlock warning switch assembly.
Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL
Inspect the unlock warning switch assembly.
Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3A instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-41 - K31-1 | Always | Below 1 Ω |
| K31-2 - Body ground | Always | Below 1 Ω |
| K31-1 or 3A-41 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-41 - MB-3 (KSW) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
Remove the front door courtesy light switch assembly (for LH).
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL
Inspect the front door courtesy light switch assembly (for LH).
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION
for RHD
Remove the front door courtesy light switch assembly (for RH).
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL
Inspect the front door courtesy light switch assembly (for RH).
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Disconnect the K52 main body ECU (multiplex network body ECU) connector.
for LHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R5-1 - K52-1 (FLCY) | Always | Below 1 Ω |
| R5-1 or K52-1 (FLCY) - Other terminals and body ground | Always | 10 kΩ or higher |
for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R4-1 - K52-6 (FLCY) | Always | Below 1 Ω |
| R4-1 or K52-6 (FLCY) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG