Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CENTER AIRBAG SENSOR ASSEMBLY › 2017.12–2018.04
RM33A0E _58 Vehicle Interior _065383 SUPPLEMENTAL RESTRAINT SYSTEMS _0327348 CENTER AIRBAG SENSOR ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CENTER AIRBAG SENSOR ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during airbag sensor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Occupant Classification System

Replacement of the airbag sensor assembly Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)
Removal/installation of the front passenger seat*1 Zero point calibration (Occupant classification system)
·

Occupant classification system

·

Passenger airbag ON/OFF indicator

·

Airbag system (Front passenger side)

·

Seat belt warning system (Front passenger)


(Click here)
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for an LHD vehicle.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.REMOVE FRONT SEAT ASSEMBLY (for Power Seat)

Hide 3.REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)

Hide 58810J 4.REMOVE CONSOLE BOX ASSEMBLY

Hide 73350C 5.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 72693 7.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 67914 8.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112A 9.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

Hide 62312B 10.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Disconnect the front door opening trim weatherstrip LH to the extent that allows the removal of the lower center pillar garnish LH.


Hide 67918A 11.REMOVE REAR DOOR SCUFF PLATE LH

Hide 62332A 12.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Disconnect the rear door opening trim weatherstrip LH to the extent that allows the removal of the lower center pillar garnish LH.


Hide 62414A 13.REMOVE LOWER CENTER PILLAR GARNISH LH

Hide 55606 14.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)

Hide 55606 15.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

Hide 67913 16.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62111A 17.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62311B 18.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Disconnect the front door opening trim weatherstrip RH to the extent that allows the removal of the lower center pillar garnish RH.


Hide 67917A 19.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62331A 20.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Disconnect the rear door opening trim weatherstrip RH to the extent that allows the removal of the lower center pillar garnish RH.


Hide 62413A 21.REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 55607 22.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 58569D 25.REMOVE FRONT FLOOR CAUTION PLATE COVER

Hide 58510D 26.DISCONNECT FRONT FLOOR CARPET ASSEMBLY

a.

for LHD:

i.
E366971

Remove the front floor carpet clip.



b.
E372079

Remove the front floor carpet clip.


c.
E372535

Disengage the 2 guides and turn back the front floor carpet assembly as shown in the illustration.


d.
E374079

Remove the front floor carpet clip.


e.
E372078

Remove the front floor carpet clip.


f.
E372540

Disengage the 2 guides and turn back the front floor carpet assembly as shown in the illustration.


Hide 58861B 27.REMOVE NO. 1 CONSOLE BOX DUCT

a.
C378612C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the clip.


b.

Remove the No. 1 console box duct as shown in the illustration.


Hide 89170 28.REMOVE AIRBAG SENSOR ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B468737C01
1.063,2.479 0.823,3.031 0.823,3.031 0.604,3.031 true 1.156,2.479 1.375,2.479 true 0.458,2.938 0.604,3.146 0.146,0.208 10 true A 1.406,2.385 1.552,2.594 0.146,0.208 10 true *a
*a Lock Lever
V113147

Release the lock (1)
V113148

Disconnect the connector (2)


Push down the part (A) in the direction indicated by the arrow (1) to release the lock, and then move the lock lever in the direction indicated by the arrow (2) shown in the illustration to disconnect the connectors.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



d.
B468739

Remove the 3 bolts and airbag sensor assembly.