Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT › 2017.12–2018.04
RM33A0E _58 Vehicle Interior _065387 HEATING / AIR CONDITIONING _0319106 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during air conditioning unit removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Steering sensor
·

Steering angle neutral point (Initialize parking assist monitor system)

·

Steering angle setting


Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

Make sure to select face mode before disconnecting the cable from the negative (-) battery terminal.


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 53607A 4.REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY

Hide 87246 5.DISCONNECT OUTLET HEATER WATER HOSE

a.
E365734

Using pliers, grip the claws of the clip and slide the clip to disconnect the outlet heater water hose.

NOTICE:
·

Do not apply excessive force to the outlet heater water hose.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87245 6.DISCONNECT INLET HEATER WATER HOSE

a.
E365736

Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose.

NOTICE:
·

Do not apply excessive force to the inlet heater water hose.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 88707 7.DISCONNECT SUCTION PIPE SUB-ASSEMBLY

a.
E365730

Remove the bolt and rotate the hook connector as shown in the illustration.


b.
E365732

Disconnect the suction pipe sub-assembly.


c.

Remove the O-ring from the suction pipe sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88710E 8.DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

a.
E365733

Disconnect the air conditioning tube and accessory assembly.


b.

Remove the O-ring from the air conditioning tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 10.REMOVE FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 45250 12.REMOVE STEERING COLUMN ASSEMBLY

Hide 13.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Hide 89343C 14.REMOVE NO. 1 CLEARANCE WARNING BUZZER (for LHD)

Hide 8598A 15.REMOVE DOOR CONTROL BATTERY (w/ Door Control Battery)

Hide 89111 16.REMOVE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) (w/o Smart Entry and Start System)

Hide 82877 17.REMOVE ECU INTEGRATION BOX RH (for LHD)

Hide 18.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for RHD)

Hide 88625Q 19.REMOVE COOLER (ROOM TEMP. SENSOR) THERMISTOR (for Automatic Air Conditioning System)

a.
E365745

Disconnect the connector and aspirator to remove the cooler (room temp. sensor) thermistor.


Hide 58569D 22.REMOVE FRONT FLOOR CAUTION PLATE COVER

a.
E372131C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Disengage the claw as shown by the arrow (1), and then pull the front floor caution plate cover as shown by the arrow (2) in the illustration to disengage the guide and remove it.


Hide 87212F 23.REMOVE REAR NO. 2 AIR DUCT

a.

for LHD:

i.
E366971

Remove the front floor carpet clip.



b.
E372079

Remove the front floor carpet clip.


c.
E377302

Disengage the 2 guides and turn back the front floor carpet assembly as shown in the illustration.


d.
E372141C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 4 claws and remove the rear No. 2 air duct as shown in the illustration.


Hide 87212 24.REMOVE REAR NO. 1 AIR DUCT

a.
E372143

Disengage the 2 claws and remove the rear No. 1 air duct.


Hide 87212H 25.REMOVE REAR NO. 4 AIR DUCT

a.
E366970

Remove the front floor carpet clip.


b.
E372078

Remove the front floor carpet clip.


c.
E377300

Disengage the 2 guides and turn back the front floor carpet assembly as shown in the illustration.


d.
E372139C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 4 claws and remove the rear No. 4 air duct as shown in the illustration.


Hide 87212G 26.REMOVE REAR NO. 3 AIR DUCT

a.
E372144

Disengage the 2 claws and remove the rear No. 3 air duct.


Hide 58543B 27.REMOVE FLOOR CARPET BRACKET RH

a.
E377304C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the clip.


b.

Disengage the claw to remove the floor carpet bracket RH as shown in the illustration.


Hide 58544B 28.REMOVE FLOOR CARPET BRACKET LH

a.
E377305C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the clip.


b.

Disengage the claw to remove the floor carpet bracket LH as shown in the illustration.


Hide 58861B 29.REMOVE NO. 1 CONSOLE BOX DUCT

a.
E378094C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the No. 1 console box duct as shown in the illustration.


Hide 55215D 30.REMOVE NO. 3 DASH PANEL INSULATOR PAD

a.
E377309C01
0.479,0.875 0.656,1.031 0.656,1.031 0.844,0.865 false 0.563,1.021 0.875,1.177 0.313,0.156 10 false *a
*a Cut


Cut each claw of the 2 clips and remove the No. 3 dash panel insulator pad.

NOTICE:

If the No. 3 dash panel insulator pad is damaged, replace it with a new one.



b.

Remove the 2 clips.


Hide 55306A 31.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

for LHD:

i.
E377310C01
1.552,1.542 2.625,1.906 true 2.635,1.792 2.844,1.979 0.208,0.188 10 true *a
*a Earth Wire


Remove the bolt and disconnect the earth wire.


ii.

Disengage each clamp.



b.

for RHD:

i.
E377348C01
1.563,1.375 2.031,1.375 true 2.667,2.26 3.021,2.031 true 3.052,1.896 3.281,2.094 0.229,0.198 10 true *a 2.042,1.26 2.25,1.448 0.208,0.188 10 true *b
*a Earth Wire
*b Relay Block Assembly
V100135

Bolt (A)
V100136

Bolt (B)


Remove the bolt (A) and disconnect the earth wire.


ii.

Remove the bolt (B).


iii.

Disengage each clamp to separate the relay block assembly.



c.
E377311C01
0,0 0,0 false
V100135

Bolt
V100136

Screw
V100137

Nut


Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.


Hide 55307C 32.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

for LHD:

i.
E377312C01
1.25,1.073 1.771,1.073 true 0.594,2.552 0.917,2.552 true 0.354,2.427 0.563,2.604 0.208,0.177 10 true *a 1.01,0.938 1.219,1.125 0.208,0.188 10 true *b
*a Earth Wire
*b Relay Block Assembly
V100135

Bolt (A)
V100136

Bolt (B)


Remove the bolt (A) and disconnect the earth wire.


ii.

Remove the bolt (B).


iii.

Disengage each clamp to separate the relay block assembly.



b.

for RHD:

i.
E377349C01
2.24,1.188 2.656,0.771 true 2.667,0.656 2.927,0.854 0.26,0.198 10 true *a
*a Earth Wire


Remove the bolt and disconnect the earth wire.


ii.

Disengage each clamp.



c.
E377313C01
0,0 0,0 false
V100135

Bolt
V100136

Screw
V100137

Nut


Remove the bolt, screw, nut and No. 2 instrument panel brace sub-assembly.


Hide 55308B 33.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

a.
E377314

Disengage each clamp.


b.
E377315C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt, nut and No. 3 instrument panel to cowl brace sub-assembly.


Hide 34.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for LHD)

Hide 82877 35.REMOVE ECU INTEGRATION BOX RH (for RHD)

Hide 87201B 36.REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY

a.
E377316

Disengage the 4 claws to remove the No. 2 air duct sub-assembly.


Hide 37.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioner unit assembly when removing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.

·

When disassembling the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.

for LHD:

i.

Disconnect the connector.

E377317C01
0.979,5.552 1.417,5.615 1.417,5.615 1,5.375 true 6.521,3.865 6.688,3.865 true 6.385,0.813 6.01,0.625 true 6.688,3.729 6.906,3.896 0.219,0.167 10 true *b 1.427,5.51 1.646,5.698 0.219,0.188 10 true *a 5.771,0.458 5.99,0.646 0.219,0.188 10 true *a
*a Earth Wire *b Connector Holder
V100135

Connector
V100136

Bolt
V100137

Nut - -



ii.

Remove the 3 bolts and disconnect the 3 earth wires.


iii.

Remove the 2 nuts and disconnect the connector holder.


iv.

Disengage each clamp.



b.

for RHD:

i.

Disconnect each connector.

E377350C01
5.927,3.938 5.333,4.021 5.333,4.021 5.906,3.677 true 0.583,1.25 1.052,1.333 true 0.354,1.135 0.667,1.292 0.313,0.156 10 false *a 5.104,3.906 5.302,4.094 0.198,0.188 10 true *a
*a Earth Wire - -
V100135

Connector
V100136

Bolt



ii.

Remove the 3 bolts and disconnect the 3 earth wires.


iii.

Disengage each clamp.


iv.
E377351C01
2.427,0.656 2.854,0.656 true 2.875,0.531 3.094,0.729 0.219,0.198 10 true *a
*a Connector Holder


Remove the 2 nuts and disconnect the connector holder.


v.

Disengage the clamp.



c.
E377318C01
0.823,2.375 1.26,2.531 true 0.906,0.583 1.333,0.25 true 1.365,0.146 1.677,0.302 0.313,0.156 10 false A 0.583,2.25 0.813,2.458 0.229,0.208 12 true *A
*A w/ Smart Entry and Start System
V100135

Release the lock (1)
V100136

Release the lock (2)


Push down the part (A) in the direction indicated by the arrow (1), to release the lock, and then move the lock lever in the direction indicated by the arrow (2) shown in the illustration to disconnect the connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



d.

w/ Smart Entry and Start System:

i.

Disconnect the connector.



e.

Disengage each clamp to separate the instrument panel wire.


f.
E365334

Turn back the front floor mat as shown in the illustration.


g.
E380283C01
0.458,2.948 0.875,2.781 true 0.271,2.854 0.438,3.021 0.167,0.167 10 true *1
*1 Cooler Unit Drain Hose Grommet


Disconnect the drain cooler hose.

NOTICE:

If the drain cooler hose is disconnected from the cooler unit drain hose grommet, make sure to replace the cooler unit drain hose grommet with a new one. Failure to do so may lead to water ingress.



h.
E370261

Remove the cooler unit drain hose grommet.


i.
E365432

Remove the 2 hole plugs.


j.
E365433

Remove the 3 bolts.


k.

Remove the 4 bolts (A).

E377320C01
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)
V100137

Nut - -



l.

Remove the bolt (B) and disconnect the brake pedal assembly.


m.

Remove the nut.


n.

Disengage each clamp.

E382592C01
0.167,0.167 0.417,0.417 0.25,0.25 12 true *A 1.688,0.75 2,0.906 0.313,0.156 10 false *B 2.417,0.167 2.667,0.417 0.25,0.25 12 true *B
*A for LHD *B for RHD
V113147

Remove in this Direction - -



o.

Disconnect each connector.


p.

Remove the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.


Hide 38.REMOVE AIR CONDITIONER UNIT ASSEMBLY

a.

Remove the 3 bolts.

E372564C01
1.313,4.146 1.813,4.146 true 3.49,4.135 3.99,4.135 true 1.823,4.031 2.073,4.219 0.25,0.188 12 true *A 4.01,4.021 4.26,4.208 0.25,0.188 12 true *A
*A w/ Claw - -



b.

w/ Claw:

i.

Disengage the 2 claws.



c.

Remove the air conditioner unit assembly from the instrument panel reinforcement assembly.