DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | Total distance traveled | Min.: 0
Max.: 16777215 |
- | - |
| Total Distance Traveled - Unit | Unit for Total Distance Traveled | km or mile | - | - |
| Vehicle Speed | Vehicle speed | Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph) |
Actual vehicle speed | ·
This is the current vehicle speed. ·
The vehicle speed is detected using the wheel speed sensors. -
There is a delay in when the vehicle speed data is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped. |
| Engine Speed | Engine speed | Min.: 0 rpm
Max.: 16383 rpm |
600 to 700 rpm: Engine idling (shift lever in P, engine warmed up and A/C off) | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Calculate Load | Load calculated by ECM | Min.: 0%
Max.: 100% |
20 to 40%: Engine idling with warmed up engine | ·
This is the engine load calculated based on the estimated intake pressure. ·
Calculate Load = Actual intake manifold pressure / maximum intake manifold pressure x 100 (%) (For example, when the actual intake manifold pressure is the same as atmospheric pressure, Calculate Load is 100%.) |
| Coolant Temperature | Engine coolant temperature | Min.: -40°C (-40°F)
Max.: 140°C (284°F) |
75 to 100°C (167 to 212°F): After warming up | This is the engine coolant temperature.
|
| Intake Air Temperature | Intake air temperature | Min.: -40°C (-40°F)
Max.: 140°C (284°F) |
Equivalent to temperature at location of mass air flow meter sub-assembly | This is the intake air temperature.
|
| Ambient Temperature | Ambient temperature | Min.: -40°C (-40°F)
Max.: 215°C (419°F) |
Equivalent to ambient air temperature | This is the ambient temperature.
|
| Engine Run Time | Engine run time | Min.: 0 sec
Max.: 65535 sec |
Time after engine start | This is the time elapsed since the engine was started.
|
| Battery Voltage | Battery voltage | Min.: 0 V
Max.: 65.5 V |
11 to 14 V: Engine idling | If 11 V or less, the characteristics of some electrical components may change. |
| BATT Voltage | Battery voltage | Min.: 0 V
Max.: 79.998 V |
11 to 14 V: Engine idling | If 11 V or less, the characteristics of some electrical components may change. |
| Glow Indicator Supported | Glow indicator supported | Unsupp or Supp | - | - |
| Throttle Position Sensor No.1 Voltage % | Absolute throttle position sensor No. 1 | Min.: 0%
Max.: 100% |
·
10 to 22%: Accelerator pedal fully released ·
64 to 96%: Accelerator pedal fully depressed |
The No. 1 throttle position sensor output is converted using 5 V = 100%.
|
| Starter SW | Starter signal | OFF or ON | ·
ON: Starter operating ·
OFF: Starter not operating |
- |
| Neutral Position SW | Park/neutral position switch assembly status | ON or OFF | ·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| Stop Light SW | Stop light switch assembly status | ON or OFF | ·
ON: Brake pedal depressed ·
OFF: Brake pedal released |
- |
| Cruise Main SW | Cruise control main switch status | ON or OFF | ·
ON: Cruise control main switch pushed ·
OFF: Cruise control main switch not pushed |
- |
| Complete Parts Monitor | Comprehensive component monitor | Not Avl or Avail | - | ·
*2 |
| Fuel System Monitor | Fuel system monitor | Not Avl or Avail | - | ·
*2 |
| Fuel System Monitor Result | Fuel system monitor | Compl or Incmpl | - | ·
*2 |
| Misfire Monitor | Misfire monitor | Not Avl or Avail | - | ·
*2 |
| EGR/VVT Monitor | EGR/VVT monitor | Not Avl or Avail | - | ·
*2 |
| EGR/VVT Monitor Result | EGR/VVT monitor | Compl or Incmpl | - | ·
*2 |
| A/F (O2) Sensor Heater Monitor | Heated oxygen sensor (air fuel ratio sensor) heater monitor | Not Avl or Avail | - | ·
*2 |
| A/F (O2) Sensor Heater Monitor Result | Heated oxygen sensor (air fuel ratio sensor) heater monitor | Compl or Incmpl | - | ·
*2 |
| A/F (O2) Sensor Monitor | Heated oxygen sensor (air fuel ratio sensor) monitor | Not Avl or Avail | - | ·
*2 |
| A/F (O2) Sensor Monitor Result | Heated oxygen sensor (air fuel ratio sensor) monitor | Compl or Incmpl | - | ·
*2 |
| Secondary Air Injection System Monitor | Secondary air injection system monitor | Not Avl or Avail | - | ·
*2 |
| Secondary Air Injection System Monitor Result | Secondary air injection system monitor | Compl or Incmpl | - | ·
*2 |
| EVAP Monitor | EVAP monitor | Not Avl or Avail | - | ·
*2 |
| EVAP Monitor Result | EVAP monitor | Compl or Incmpl | - | ·
*2 |
| Heated Catalyst Monitor | Heated catalyst monitor | Not Avl or Avail | - | ·
*2 |
| Heated Catalyst Monitor Result | Heated catalyst monitor | Compl or Incmpl | - | ·
*2 |
| Catalyst Monitor | Catalyst monitor | Not Avl or Avail | - | ·
*2 |
| Catalyst Monitor Result | Catalyst monitor | Compl or Incmpl | - | ·
*2 |
| TC Terminal | TC terminal status | ON or OFF | - | - |
| MIL | MIL status | ON or OFF | OFF | - |
| MIL ON Run Distance | Distance driven with MIL on | Min.: 0 km (0 mile)
Max.: 65535 km (40723 mile) |
- | This is the distance driven since the MIL was illuminated. |
| Running Time from MIL ON | Running time from MIL on | Min.: 0 min
Max.: 65535 min |
Running time since the MIL illuminated | - |
| Time after DTC Cleared | Time after DTCs cleared | Min.: 0 min
Max.: 65535 min |
Time after DTCs cleared | This is the time elapsed since the DTCs were cleared (or the vehicle left the factory). Time elapsed after the engine switch is turned off is not counted. |
| Distance from DTC Cleared | Distance driven after DTCs cleared | Min.: 0 km (0 mile)
Max.: 65535 km (40723 mile) |
Distance driven after DTCs cleared | This is the distance driven since the DTCs were cleared (or after the vehicle left the factory). |
| Warmup Cycle Cleared DTC | Warmup cycles after DTCs cleared | Min.: 0
Max.: 255 |
- | ·
This is the number of warmup cycles after the DTCs were cleared. ·
This is the number of times the engine was warmed up* since the DTCs were cleared (or after the vehicle left the factory). *: An engine warmup is defined as the engine coolant temperature rising 20°C (68°F) or higher and reaching a temperature of 70°C (158°F) or higher after the engine is started. |
| OBD Requirements | OBD requirement | - | EOBD (Euro OBD) | - |
| Number of Emission DTC | Emissions-related DTCs | Min.: 0
Max.: 127 |
- | This is the number of emissions-related DTCs. |
| Accel Position from EFI | Absolute accelerator pedal position | Min.: 0%
Max.: 127.5% |
- | - |
| NT Sensor Speed | Input turbine speed | Min.: 0 rpm
Max.: 12750 rpm |
·
Equal to engine speed: Lock-up on (after warming up the engine) ·
Nearly equal to engine speed: Lock-up off (engine idling with shift lever in N) |
Data is displayed in increments of 50 rpm. |
| NC Sensor Speed | Counter gear speed | Min.: 0 rpm
Max.: 12750 rpm |
- | Data is displayed in increments of 50 rpm. |
| Shift SW Status (P Range) | Park/neutral position switch assembly status | ON or OFF | ·
ON: Shift lever in P ·
OFF: Shift lever not in P |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| Shift SW Status (R Range) | Park/neutral position switch assembly status | ON or OFF | ·
ON: Shift lever in R ·
OFF: Shift lever not in R |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| Shift SW Status (N Range) | Park/neutral position switch assembly status | ON or OFF | ·
ON: Shift lever in N ·
OFF: Shift lever not in N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| Shift SW Status (N,P Range) | Park/neutral position switch assembly status | ON or OFF | ·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| Shift SW Status (N,P Range) Supported | Status of park/neutral position switch assembly (N or P) supported | Unsupp or Supp | Supp | - |
| Shift SW Status (S Range) | S mode select switch status | ON or OFF | ·
ON: Shift lever in S, "+" or "-" ·
OFF: Shift lever not in S, "+" or "-" |
- |
| Shift SW Status (D Range) | Park/neutral position switch assembly status | ON or OFF | ·
ON: Shift lever in D or S ·
OFF: Shift lever not in D or S |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
| A/T Oil Temperature No.1 | ATF temperature sensor value | Min.: -40°C (-40°F)
Max.: 150°C (302°F) |
·
Approximately 80°C (176°F): After stall speed test ·
Equal to ambient temperature: When engine is cold |
If the value is -40°C (-40°F) or 150°C (302°F), the ATF temperature sensor circuit is open or shorted. |
| NT Sensor Voltage | Input speed sensor NT output voltage | Min.: 0.000 V
Max.: 4.999 V |
0.1 to 1.9 V | - |
| NC Sensor Voltage | Counter gear speed sensor output voltage | Min.: 0.000 V
Max.: 4.999 V |
0.1 to 1.9 V | - |
| Lock Up Status | Lock up | ON or OFF | ·
ON: Lock-up operating ·
OFF: Lock-up not operating |
- |
| Shift Status | ECM gear shift command | 1st, 2nd, 3rd, 4th, 5th or 6th | Same as actual gear | - |
| Solenoid (SLT) | Solenoid (SLT) valve status | ON or OFF | ·
ON: Solenoid (SLT) valve operating ·
OFF: Solenoid (SLT) valve not operating |
- |
| Solenoid (SLU) | Solenoid (SLU) valve status | ON or OFF | ·
ON: Solenoid (SLU) valve operating ·
OFF: Solenoid (SLU) valve not operating |
- |
| Solenoid (SL1) | Solenoid (SL1) valve status | ON or OFF | ·
ON: Solenoid (SL1) valve operating ·
OFF: Solenoid (SL1) valve not operating |
The value of this item only changes when performing an Active Test. |
| Solenoid (SL2) | Solenoid (SL2) valve status | ON or OFF | ·
ON: Solenoid (SL2) valve operating ·
OFF: Solenoid (SL2) valve not operating |
The value of this item only changes when performing an Active Test. |
| Solenoid (SL3) | Solenoid (SL3) valve status | ON or OFF | ·
ON: Solenoid (SL3) valve operating ·
OFF: Solenoid (SL3) valve not operating |
The value of this item only changes when performing an Active Test. |
| Solenoid (SL4) | Solenoid (SL4) valve status | ON or OFF | ·
ON: Solenoid (SL4) valve operating ·
OFF: Solenoid (SL4) valve not operating |
The value of this item only changes when performing an Active Test. |
| Solenoid (SL) | Solenoid (SL) valve status | ON or OFF | ·
ON: Solenoid (SL) valve operating ·
OFF: Solenoid (SL) valve not operating |
- |
*1: Refer to DTC P070513/P070562.
Click hereDrivetrain>U761E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>P070513
*2:
Avail: The monitor is available on this vehicle.
Not Avl: The monitor is not available on this vehicle.
Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed at least once at sometime in the past. This item does not change when the engine switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or cable is disconnected from the negative (-) battery terminal.
Enter the following menus: Powertrain / Engine / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Throttle Sensor Position | Throttle sensor position | Min.: 0%
Max.: 100% |
·
0%: Accelerator pedal fully released ·
50 to 80%: Accelerator pedal fully depressed (engine running) |
·
This is the throttle valve opening amount used for engine control. ·
This value has no meaning when the engine switch is on (IG) and the engine is stopped. ·
The throttle valve opening amount during engine idling is indicated by 0%. |
| Sport Shift Up SW | Sport shift up switch status | ON or OFF | ·
ON: Shift lever held in "+" ·
OFF: Shift lever not held in "+" |
- |
| Sport Shift Down SW | Sport shift down switch status | ON or OFF | ·
ON: Shift lever held in "-" ·
OFF: Shift lever not held in "-" |
- |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Activate the TC Terminal | Connects and disconnects TC and TE1
(changes to the fluid temperature detection mode) |
ON/OFF | ·
Confirm that the vehicle is stopped. ·
ON: TC and TE1 (CG) are connected. ·
OFF: TC and TE1 (CG) are disconnected. ·
The MIL will not blink when "Activate the TC Terminal / ON" is selected. |
| Control the Shift Position | Operates the solenoid valves to allow gears to be selected manually | ·
Press "→" button: Upshift occurs ·
Press "←" button: Downshift occurs |
Can be used to check the operation of the solenoid valves.
Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes. Do not downshift at high speeds. Doing so will damage the automatic transaxle assembly. [Vehicle Condition]
50 km/h (31 mph) or less |
| Activate the Solenoid (SLU) | Operates the solenoid (SLU) valve | ON/OFF | [Vehicle Condition]
·
Engine not running ·
Shift lever in P or N |
| Activate the Solenoid (SLT) | Operates the solenoid (SLT) valve to raise the line pressure | ON/OFF
|
[Vehicle Condition]
·
Vehicle stopped ·
IDL: ON |
| Activate the Lock Up Solenoid | Operates the solenoid (SLU and SL) valves to control the automatic transaxle lock-up condition | ON/OFF | Can be used to check the operation of the solenoid (SLU and SL) valves.
[Vehicle Condition]
·
Vehicle speed: 70 km/h (43 mph) or more ·
Gear: Highest gear ·
Throttle valve opening angle: 20% or more |
| Activate the Solenoid (SL) | Operates the solenoid (SLT) valve | ON/OFF | [Vehicle Condition]
·
Engine not running ·
Shift lever in P or N |
| Activate the Solenoid (SL1) | Operates the solenoid (SL1) valve | ON/OFF | [Vehicle Condition]
·
Engine not running ·
Shift lever in P or N |
| Activate the Solenoid (SL2) | Operates the solenoid (SL2) valve | ON/OFF | [Vehicle Condition]
·
Engine not running ·
Shift lever in P or N |
| Activate the Solenoid (SL3) | Operates the solenoid (SL3) valve | ON/OFF | [Vehicle Condition]
·
Engine not running ·
Shift lever in P or N |
| Activate the Solenoid (SL4) | Operates the solenoid (SL4) valve | ON/OFF | [Vehicle Condition]
·
Engine not running ·
Shift lever in P or N |
Performing the Active Test "Activate the Solenoid (SLT)" allows the change in line pressure to be checked with SST installed to the automatic transaxle assembly. The same SST is used for the Hydraulic Test.
Click hereDrivetrain>U761E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>HYDRAULIC TEST
Note that the pressure readings for the Active Test and Hydraulic Test are different.