Home › Drivetrain › U761E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2018.04–2021.02
RM33A0E _52 Drivetrain _072210 U761E AUTOMATIC TRANSMISSION / TRANSAXLE _0351183 AUTOMATIC TRANSAXLE SYSTEM C

U761E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P07457F  Pressure Control Solenoid "A" Actuator Stuck Off  


SYSTEM DESCRIPTION

The ECM uses the vehicle speed signal and signals from the transmission speed sensors (NC and NT) to detect the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear).

The ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical malfunctions of the solenoid valves and transmission valve body assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P07457F Pressure Control Solenoid "A" Actuator Stuck Off All of the following conditions are met (2-trip detection logic):
·

The engine coolant temperature is 40°C (104°F) or higher.

·

The ATF temperature is -10°C (14°F) or higher.

·

The vehicle is being driven with the shift lever in D.

·

No malfunctions are detected in the solenoid (SL1, SL2, SL3 and SL4) valves, transmission revolution sensors (NT and NC), coolant temperature sensor, oil temperature sensor, knock sensor, electronic throttle or CAN communication system.

·

Any of the following conditions are met:

-

When the ECM commands the transaxle to shift to 1st, 2nd, 3rd or 4th gear, the engine overruns (neutral status).

-

When the ECM commands the transaxle to shift to 5th or 6th gear, the actual gear changes to 4th.



·

Solenoid (SL1) valve remains open or closed

·

Transmission valve body assembly is blocked

·

Automatic transaxle assembly (clutch, brake, gear, etc.)


Comes on DTC stored SAE Code:
P0746

DTC Detection Condition Patterns:
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnostic Condition The engine coolant temperature is 40°C (104°F) or higher. ○ ○ ○ ○ ○ ○
The ATF temperature is -10°C (14°F) or higher. ○ ○ ○ ○ ○ ○
The vehicle is being driven with the shift lever in D. ○ ○ ○ ○ ○ ○
No malfunctions are detected in the solenoid (SL1, SL2, SL3 and SL4) valves, transmission revolution sensors (NT and NC), coolant temperature sensor, oil temperature sensor, knock sensor, electronic throttle or CAN communication system. ○ ○ ○ ○ ○ ○
Malfunction Condition When the ECM commands the transaxle to shift to 1st gear, the engine overruns (neutral status). ○ - - - - -
When the ECM commands the transaxle to shift to 2nd gear, the engine overruns (neutral status). - ○ - - - -
When the ECM commands the transaxle to shift to 3rd gear, the engine overruns (neutral status). - - ○ - - -
When the ECM commands the transaxle to shift to 4th gear, the engine overruns (neutral status). - - - ○ - -
When the ECM commands the transaxle to shift to 5th gear, the actual gear changes to 4th. - - - - ○ -
When the ECM commands the transaxle to shift to 6th gear, the actual gear changes to 4th. - - - - - ○
Duration 0.5 seconds or more 0.5 seconds or more 0.5 seconds or more 0.5 seconds or more 0.8 seconds or more 0.8 seconds or more
Detection Logic 2-trip detection logic 2-trip detection logic 2-trip detection logic 2-trip detection logic 2-trip detection logic 2-trip detection logic

HINT:

This DTC is stored when any of the above detection patterns are met.


MONITOR DESCRIPTION

The ECM commands gear shifts by turning the solenoid valves on and off. According to the input shaft revolution (speed) and intermediate (counter) shaft revolution (speed), the ECM detects the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear). When the gear commanded by the ECM and the actual gear are not the same, the ECM illuminates the MIL and stores a DTC.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the engine switch off and wait for 2 minutes or more.

5.

Turn the engine switch on (IG) and turn the GTS on.

6.

Start the engine.

7.

Perform the D Position Shift Test inspection in Road Test.

Click hereDrivetrain>U761E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P07457F.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

CAUTION:
·
A371909

Strictly obey all traffic rules and regulations.

·

Do not drive the vehicle with the GTS cable contacting the pedals, shift lever or steering wheel.

·

Driving the wheel with the GTS cable contacting these areas could impede vehicle control, resulting in a serious accident.


·
A356953

Do not operate the GTS while driving the vehicle.

·

Operating the GTS while driving the vehicle will prevent you from paying sufficient attention to vehicle surroundings, and could result in a serious accident.



NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U761E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P07457F)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

e.

Read the DTCs using the GTS.

Result:
Result Proceed to
Only DTC P07457F is output A
DTC P07457F and other DTCs are output B


HINT:

If a solenoid valve is stuck OFF, DTCs for several solenoid valves including the malfunctioning solenoid valve will be stored.




A

3.INSPECT SOLENOID (SL1) VALVE

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE SHIFT POSITION)
2.PERFORM ACTIVE TEST USING GTS (CONTROL THE SHIFT POSITION)
NOTICE:

This test should always be performed with at least 2 people.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Transmission / Active Test / Control the Shift Position.


g.

Perform the Active Test according to the display on the GTS.

HINT:

Comparing the gear commanded by the Active Test with the actual gear enables confirmation of the problem.

Click hereDrivetrain>U761E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART


Powertrain > Transmission > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Control the Shift Position Operates the solenoid valves to allow gears to be selected manually
·

Press "→" button: Upshift occurs

·

Press "←" button: Downshift occurs


Can be used to check the operation of the solenoid valves.
Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes.
Do not downshift at high speeds. Doing so will damage the automatic transaxle assembly.
[Vehicle Condition]

50 km/h (31 mph) or less


Powertrain > Transmission > Active Test
Tester Display
Control the Shift Position
50004 373 42009
NOTICE:
·

This Active Test can be performed when the vehicle is stopped.

·

When shifting gears using the Active Test, do not operate the accelerator pedal for 2 seconds before and after shifting gears.



HINT:

The gear commanded by the ECM is shown in the Data List / Shift Status display on the GTS.



h.

Check the vehicle speed and gear when the engine speed is 1000 rpm.

HINT:

As the torque converter clutch has not engaged, it may be difficult to obtain the speeds specified for 4th, 5th and 6th gear, however a difference of speed should still be evident following each gear change.


Standard:
1st 2nd 3rd 4th 5th 6th
8 to 12 km/h
(5 to 7 mph)
15 to 19 km/h
(9 to 12 mph)
21 to 25 km/h
(13 to 16 mph)
31 to 35 km/h
(19 to 22 mph)
44 to 48 km/h
(27 to 30 mph)
52 to 56 km/h
(32 to 35 mph)



i.

Compare the ECM commanded gear and actual gear.

Result:
Actual Gear during Malfunction ECM Commanded Gear Proceed to
1st 2nd 3rd 4th 5th 6th
Solenoid (SL1) valve Stuck ON 1st 2nd 3rd 4th 4th 4th A
Stuck OFF N*1 N*1 N*1 N*1 5th 6th
Solenoid (SL2) valve Stuck ON 4th 4th 4th 4th 5th 6th B
Stuck OFF 1st 2nd 3rd 1st N*1 N*1
Solenoid (SL3) valve Stuck ON 2nd 2nd 3rd 4th 5th 6th C
Stuck OFF 1st 1st 3rd 4th 5th N*1
Solenoid (SL4) valve Stuck ON 3rd 3rd 3rd 4th 5th 5th D
Stuck OFF 1st 2nd 1st 4th N*1 6th
Solenoid (SLT) valve Stuck ON N*2 N*2 N*2 N*2 N*2 N*2 E
Stuck OFF*3 1st 2nd 3rd 4th 5th 6th


HINT:
·

*1: Neutral

·

*2: If the solenoid (SLT) valve is stuck ON, the line pressure will be low. Therefore, the amount of torque that can be transmitted by each gear will be lower than the normal limit. When the engine power exceeds this limit, the engine speed will increase freely.

·

*3: When the solenoid (SLT) valve is stuck OFF, gear shifting will be normal.





A

3.INSPECT SOLENOID (SL1) VALVE

B

C

D

E

3.INSPECT SOLENOID (SL1) VALVE
a.
C201747C02
1.49,0.875 0.635,0.646 false 1.781,0.865 2.479,0.625 false 1.49,3.125 0.635,2.896 false 1.781,3.125 2.479,2.885 false 0.49,0.521 0.667,0.719 0.177,0.198 10 1 2.531,0.5 2.708,0.698 0.177,0.198 10 2 1.177,4.198 1.385,4.406 0.208,0.208 10 (-) 1.917,4.208 2.146,4.406 0.229,0.198 10 (+) 0.51,2.771 0.688,2.969 0.177,0.198 10 1 2.521,2.76 2.698,2.958 0.177,0.198 10 2 0.135,0.135 0.354,0.344 0.219,0.208 10 *1
*1 Solenoid (SL1) Valve


Remove the solenoid (SL1) valve.

Click hereDrivetrain>U761E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly.

Click hereDrivetrain>U761E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>REMOVAL


OK:

There is no foreign matter on each valve and they operate smoothly.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY