Home › Drivetrain › U761E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2018.04–2021.02
RM33A0E _52 Drivetrain _072210 U761E AUTOMATIC TRANSMISSION / TRANSAXLE _0351183 AUTOMATIC TRANSAXLE SYSTEM C

U761E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P079112  Intermediate Shaft Speed Sensor "A" Circuit Short to Battery  P079114  Intermediate Shaft Speed Sensor "A" Circuit Short to Ground or Open  P079131  Intermediate Shaft Speed Sensor "A" No Signal  


DESCRIPTION

The output speed sensor NC detects the rotation speed of the counter gear, which indicates the intermediate shaft revolution (speed) of the transaxle. By comparing the input speed sensor NT signal with the output speed sensor NC signal, the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions, thus, providing smooth gear shifts.

C370676C01
2.167,3.333 2.417,3.333 2.417,3.333 3.167,2.417 true 3.667,2.667 4.25,3.333 4.25,3.333 4.5,3.333 true 2,0.5 2.25,0.5 2.25,0.5 3.25,1.75 true 4,1.75 4.667,0.5 4.667,0.5 4.917,0.5 true 1.802,0.427 2.115,0.583 0.313,0.156 10 false *1 4.979,0.427 5.292,0.583 0.313,0.156 10 false *2 1.969,3.26 2.281,3.417 0.313,0.156 10 false *3 4.573,3.26 4.885,3.417 0.313,0.156 10 false *4
*1 Counter Gear *2 C2 Piston
*3 Output Speed Sensor NC *4 Input Speed Sensor NT


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P079112 Intermediate Shaft Speed Sensor "A" Circuit Short to Battery All of the following conditions are met (1-trip detection logic):
·

The battery voltage is 8 V or more.

·

The engine switch is on (IG).

·

The starter is off.

·

The output speed sensor NC input voltage is more than 1.9 V for 2 seconds.


·

Wiring harness connector

·

Transmission revolution sensor (Output speed sensor NC)

·

Transmission wire

·

ECM


Comes on DTC stored SAE Code:
P07C6
P079114 Intermediate Shaft Speed Sensor "A" Circuit Short to Ground or Open All of the following conditions are met (1-trip detection logic):
·

The battery voltage is 8 V or more.

·

The engine switch is on (IG).

·

The starter is off.

·

The output speed sensor NC input voltage is less than 0.1 V for 2 seconds.


·

Wiring harness connector

·

Transmission revolution sensor (Output speed sensor NC)

·

Transmission wire

·

ECM


Comes on DTC stored SAE Code:
P07C5
P079131 Intermediate Shaft Speed Sensor "A" No Signal All of the following conditions are met (1-trip detection logic):
·

The vehicle is being driven with the shift lever in D.

·

The vehicle speed is 11 km/h (7 mph) or more.

·

The speed indicated by the output speed sensor NC is less than 300 rpm for 2 seconds.


·

Wiring harness connector

·

Transmission revolution sensor (Output speed sensor NC)

·

Transmission wire

·

ECM


Comes on DTC stored SAE Code:
P0793

MONITOR DESCRIPTION

The NC terminal of the ECM detects a revolution signal from the output speed sensor NC (counter gear RPM). The ECM calculates gear shifts by comparing the input speed sensor NT signal to the output speed sensor NC signal.

If the intermediate (counter) shaft revolution is less than 300 rpm* although the vehicle speed is 11 km/h (7 mph) or more, the ECM interprets this as a malfunction, illuminates the MIL and stores a DTC.

*: Pulse is not output or is irregularly output.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the engine switch off and wait for 2 minutes or more.

5.

Turn the engine switch on (IG) and turn the GTS on.

6.

Start the engine.

7.

Perform the D Position Shift Test inspection in Road Test and drive the vehicle for 2 seconds or more at 11 km/h (7 mph) or more.

Click hereDrivetrain>U761E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P079112, P079114 or P079131.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U761E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


DATA LIST


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Transmission / Data List.


g.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NC Sensor Speed Counter gear speed Min.: 0 rpm
Max.: 12750 rpm
- Data is displayed in increments of 50 rpm.
Powertrain > Transmission > Data List
Tester Display
NC Sensor Speed
50003 373 176
HINT:
·

NC Speed Sensor is always 0 while driving: Open or short in the sensor or circuit.

·

NC Speed Sensor is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor malfunction, improper installation or intermittent connection malfunction in the circuit.





PROCEDURE

1.READ VALUE USING GTS (NC SENSOR SPEED AND NC SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List.


e.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NC Sensor Speed Counter gear speed Min.: 0 rpm
Max.: 12750 rpm
- Data is displayed in increments of 50 rpm.
NC Sensor Voltage Counter gear speed sensor output voltage Min.: 0 V
Max.: 4.999 V
0.1 to 1.9 V -
Powertrain > Transmission > Data List
Tester Display
NC Sensor Speed
NC Sensor Voltage
50003 373 176,177

Result:
Result Proceed to
Data List values are normal A
Data List values are not normal B



A

B

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NC)
2.INSPECT TRANSMISSION REVOLUTION SENSOR (NC)
a.
C376061C06
1.5,0.115 1.917,0.365 0.417,0.25 0.969,1.813 1.385,1.146 true 1.948,1.813 1.531,1.146 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.583,0.156 1.896,0.354 0.313,0.198 10 false C54 0.823,1.833 1.281,2.031 0.458,0.198 10 false NCO 1.844,1.833 2.302,2.031 0.458,0.198 10 false NCB
*a Front view of wire harness connector
(to Wiring Harness Connector)


Disconnect the C54 wiring harness connector connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C54-3 (NCO) - Body ground Always 99 to 101 Ω


c.

Turn the engine switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C54-4 (NCB) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT WIRING HARNESS CONNECTOR

NG

6.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
3.INSPECT WIRING HARNESS CONNECTOR

b.

Measure the resistance according to the value(s) in the table below.

C267935C35
1.115,0.698 1.51,0.917 0.396,0.219 5.615,0.698 6.01,0.917 0.396,0.219 1.115,2.01 1.375,1.24 true 1.719,2.021 1.521,1.24 true 6.344,1.948 6.188,1.323 true 5.917,1.948 6.052,1.323 true 2.604,0.125 2.917,0.323 0.313,0.198 10 false *1 0.354,0.625 0.667,0.823 0.313,0.198 10 false *a 4.875,0.625 5.188,0.823 0.313,0.198 10 false *b 6.24,1.99 6.635,2.188 0.396,0.198 10 false NCO 1.615,2.052 2.01,2.25 0.396,0.198 10 false NCB 5.781,1.99 6.177,2.188 0.396,0.198 10 false NCB 0.958,2.052 1.354,2.25 0.396,0.198 10 false NCO 1.26,0.729 1.656,0.927 0.396,0.198 10 false A 5.688,0.729 6.083,0.927 0.396,0.198 10 false C54
*1 Wiring Harness Connector - -
*a Transmission wire side *b ECM side


Standard Resistance:
Tester Connection Condition Specified Condition
C54-3 (NCO) - A-3 (NCO) Always Below 1 Ω
C54-4 (NCB) - A-4 (NCB) Always Below 1 Ω
C54-3 (NCO) or A-3 (NCO) - Other terminals Always 10 kΩ or higher
C54-4 (NCB) or A-4 (NCB) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT TRANSMISSION REVOLUTION SENSOR (SPEED SENSOR INSTALLATION)

NG

4.INSPECT TRANSMISSION REVOLUTION SENSOR (SPEED SENSOR INSTALLATION)
a.

Remove the transmission valve body assembly.

Click hereDrivetrain>U761E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>REMOVAL


b.
C133219

Make sure that the connector is properly connected, and check the transmission revolution sensor installation.

Click hereDrivetrain>U761E (AUTOMATIC TRANSMISSION / TRANSAXLE)>SPEED SENSOR>INSTALLATION

OK:

The installation bolts are tightened properly and there is no clearance between the transmission revolution sensor and transmission valve body assembly.



Result:
Proceed to
OK
NG



OK

5.INSPECT TRANSMISSION WIRE

NG

REPAIR OR REPLACE TRANSMISSION REVOLUTION SENSOR

5.INSPECT TRANSMISSION WIRE
a.
C275092C02
2.677,1.208 3,1.469 0.323,0.26 1.677,1.063 1.333,2.167 false 1.833,1.052 2.26,2.167 false 1.917,3.948 1.781,4.333 false 2.167,3.938 2.521,4.333 false 0.073,0.094 0.385,0.25 0.313,0.156 10 *a 0.5,0.5 0.813,0.656 0.313,0.156 10 *b 0.583,3.094 0.896,3.25 0.313,0.156 10 *c 2.802,1.25 2.958,1.448 0.156,0.198 10 A 2.104,2.198 2.563,2.396 0.458,0.198 10 NCO 1.156,2.198 1.615,2.396 0.458,0.198 10 NCB 1.656,4.365 2.115,4.563 0.458,0.198 10 NCO 2.427,4.365 2.885,4.563 0.458,0.198 10 NCB
*a Component without harness connected
(Transmission Wire)
*b Wiring harness connector side
*c Transmission revolution sensor side


Disconnect the transmission revolution sensor connector from the transmission wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (NCO) sensor side - A-3 (NCO) wiring harness connector side Always Below 1 Ω
4 (NCB) sensor side - A-4 (NCB) wiring harness connector side Always Below 1 Ω
3 (NCO) sensor side or A-3 (NCO) wiring harness connector side - Body ground and other terminals Always 10 kΩ or higher
4 (NCB) sensor side or A-4 (NCB) wiring harness connector side - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

6.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
a.

Disconnect the C58 ECM connector.


b.

Disconnect the C54 wiring harness connector connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C58-73 (NCB) - C54-4 (NCB) Always Below 1 Ω
C58-74 (NCO) - C54-3 (NCO) Always Below 1 Ω
C58-73 (NCB) or C54-4 (NCB) - Body ground and other terminals Always 10 kΩ or higher
C58-74 (NCO) or C54-3 (NCO) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR