Home › Drivetrain › U761E (AUTOMATIC TRANSMISSION / TRANSAXLE) › OIL COOLER › 2018.04–2021.02
RM33A0E _52 Drivetrain _072210 U761E AUTOMATIC TRANSMISSION / TRANSAXLE _0351189 OIL COOLER A

U761E AUTOMATIC TRANSMISSION / TRANSAXLE  OIL COOLER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission oil cooler removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Smart Entry and Start System

*2: w/o Smart Entry and Start System

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
Possible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)for U761E Initialization
(Click here)for U761E Registration
Impossible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM*1 Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Replacement of ECM*2 Perform code registration (Immobiliser system)
·

Wireless door lock control system

·

Engine start


See Service Bulletin for the registration method.

PROCEDURE

Hide 53295E 1.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 17750A 2.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 17700 3.REMOVE AIR CLEANER ASSEMBLY

Hide 4.DRAIN ENGINE COOLANT

Hide 16281N 5.DISCONNECT NO. 4 WATER BY-PASS HOSE

a.
C395094

Slide the clip and disconnect the No. 4 water by-pass hose from the transmission oil cooler.

HINT:

Use a container to catch any coolant which flows out of the No. 4 water by-pass hose and transmission oil cooler.



Hide 16267K 6.DISCONNECT NO. 3 WATER BY-PASS HOSE

a.
C395089

Slide the clip and disconnect the No. 3 water by-pass hose from the transmission oil cooler.

HINT:

Use a container to catch any coolant which flows out of the No. 3 water by-pass hose and transmission oil cooler.



Hide 7.DISCONNECT NO. 1 TRANSMISSION OIL COOLER HOSE ASSEMBLY

a.
C386738

Slide the 2 clips and disconnect the No. 1 transmission oil cooler hose assembly from the transmission oil cooler.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the No. 1 transmission oil cooler hose assembly and transmission oil cooler.



Hide 33493A 8.REMOVE TRANSMISSION OIL COOLER

a.
C386740

Remove the 2 bolts and transmission oil cooler from the front engine mounting bracket.

HINT:

Use a container to catch any coolant and automatic transaxle fluid which flow out of the transmission oil cooler.