Home › Vehicle Exterior › WINDOW / GLASS › HEATED WINDSHIELD DEFROSTER SYSTEM › from 2018.04
RM33A0E _59 Vehicle Exterior _065390 WINDOW / GLASS _0351208 HEATED WINDSHIELD DEFROSTER SYSTEM J

WINDOW / GLASS  HEATED WINDSHIELD DEFROSTER SYSTEM  Heated Windshield Defroster System does not operate  


DESCRIPTION

When the front window deicer switch assembly is operated, the operation signal is transmitted to the air conditioning amplifier assembly directly. When the air conditioning amplifier assembly receives the signal, it turns on the HWD NO. 1 relay, HWD NO. 2 relay and HWD NO. 3 relay to operate the heated windshield defroster system.

WIRING DIAGRAM

B509847E01
4.281,0.906 4.74,1.104 0.458,0.198 10 false ECM 4.115,1.563 5.229,1.875 1.115,0.313 10 false ECU-IG1 NO. 3 5.844,1.365 6.813,1.833 0.969,0.469 10 false from IG1-NO. 1 Relay 5.802,5.146 6.75,5.521 0.948,0.375 10 false from Battery 4.125,3.927 4.979,4.135 0.854,0.208 10 false HWD NO. 1 4.24,3.396 5.177,3.604 0.938,0.208 10 false DEICER 2.281,3.573 3.25,3.802 0.969,0.229 10 false HWD NO. 3 1.479,1.833 3.458,2.344 1.979,0.51 10 false Front Window Deicer Switch 0.625,1.406 1.083,1.604 0.458,0.198 10 false DFAC 0.635,2.813 1.094,3.01 0.458,0.198 10 false FDEF 2.271,5.01 3.083,5.198 0.813,0.188 10 false HWD NO. 1 3.656,6.146 7.063,6.552 3.406,0.406 10 false No. 2 Heated Windshield Defroster (Windshield Glass) 4.115,5.313 4.969,5.49 0.854,0.177 10 false HWD NO. 2 2.302,6.365 3.125,6.573 0.823,0.208 10 false HWD NO. 2 0.688,6.833 1.146,7.031 0.458,0.198 10 false TAM 0.656,7.833 1.115,8.031 0.458,0.198 10 false SG-2 0.083,8.292 2.448,8.542 2.365,0.25 10 false Air Conditioning Amplifier Assembly 4.625,8.219 6.531,8.438 1.906,0.219 10 false : CAN Communication Line 3.698,4.781 7.125,5.094 3.427,0.313 10 false No. 1 Heated Windshield Defroster (Windshield Glass) 5.844,3.802 6.792,4.177 0.948,0.375 10 false from Battery 3.438,1.281 3.594,1.479 0.156,0.198 10 false 5 1.729,1.281 1.938,1.479 0.208,0.198 10 false 2 3.188,1.271 3.417,1.51 0.229,0.24 10 false IG 2,1.271 2.208,1.469 0.208,0.198 10 false E 3.021,2.719 3.177,2.917 0.156,0.198 10 false 1 3.042,3.135 3.198,3.333 0.156,0.198 10 false 5 2.115,3.125 2.271,3.323 0.156,0.198 10 false 3 2.083,2.708 2.24,2.906 0.156,0.198 10 false 2 3.021,4.198 3.177,4.396 0.156,0.198 10 false 5 2.135,4.594 2.292,4.792 0.156,0.198 10 false 2 3,4.594 3.156,4.792 0.156,0.198 10 false 1 2.156,4.219 2.313,4.417 0.156,0.198 10 false 3 3.99,4.208 4.146,4.406 0.156,0.198 10 false 2 4.802,4.188 4.958,4.385 0.156,0.198 10 false 1 4.208,4.219 4.365,4.417 0.156,0.198 10 false B 4.615,4.219 4.771,4.417 0.156,0.198 10 false E 4.198,5.583 4.354,5.781 0.156,0.198 10 false B 4.604,5.583 4.76,5.781 0.156,0.198 10 false E 4.792,5.573 4.948,5.771 0.156,0.198 10 false 1 4.021,5.573 4.177,5.771 0.156,0.198 10 false 2 3,5.573 3.156,5.771 0.156,0.198 10 false 5 2.125,5.948 2.281,6.146 0.156,0.198 10 false 2 3,5.958 3.156,6.156 0.156,0.198 10 false 1 2.115,5.573 2.271,5.771 0.156,0.198 10 false 3 2.115,6.729 2.271,6.927 0.156,0.198 10 false 2 3.01,6.729 3.167,6.927 0.156,0.198 10 false 1 1.135,1.385 1.438,1.583 0.302,0.198 10 false K55 1.167,2.635 1.375,2.833 0.208,0.198 10 false 17 1.125,2.823 1.438,3.031 0.313,0.208 10 false K54 1.479,1.635 1.854,1.906 0.375,0.271 10 false K148 3.688,4.604 4.344,4.865 0.656,0.26 10 false A80 3.667,5.979 4.302,6.198 0.635,0.219 10 false A81 1.167,6.635 1.375,6.833 0.208,0.198 10 false 13 1.135,6.823 1.51,7.042 0.375,0.219 10 false K55 1.198,7.635 1.406,7.833 0.208,0.198 10 false 2 1.125,7.833 1.448,8.021 0.323,0.188 10 false K55 1.177,1.177 1.385,1.375 0.208,0.198 10 false 29 1.948,7.302 3.469,7.531 1.521,0.229 10 false Thermistor Assembly 1.948,7.135 2.271,7.344 0.323,0.208 10 false A17 5.823,3.208 6.792,3.677 0.969,0.469 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the battery voltage is low, the heated windshield defroster system may not operate due to operation of battery load control, check the Data List item "Battery Control Count (Body ECU)".

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DATA LIST / ACTIVE TEST

·

The heated windshield defroster system uses the CAN communication system. First, confirm that there are no malfunctions in the communication system by checking the communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure

Click hereVehicle Exterior>WINDOW / GLASS>HEATED WINDSHIELD DEFROSTER SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the ambient temperature is 4.5°C (40°F) or higher, or if a malfunction of the ambient temperature sensor (thermistor assembly) is detected, the HWD NO. 3 relay will be deactivated and the front window deicer switch indicator light will blink.



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Clear DTCs
50002 121

b.

Recheck for DTCs.

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
DTC B1412 is output A
DTC B1412 is not output B



A

B

2.PERFORM ACTIVE TEST USING GTS
2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
HWD Relay Heated windshield defroster (windshield glass) OFF or ON -
Body Electrical > Air Conditioner > Active Test
Tester Display
HWD Relay
50004 121 102
OK:

The heated windshield defroster system operates normally.



Result:
Result Proceed to
OK A
NG (Both No. 1 and No. 2 heated windshield defroster does not warm up.) B
NG (Only No. 1 heated windshield defroster does not warm up.) C
NG (Only No. 2 heated windshield defroster does not warm up.) D



A

3.INSPECT FRONT WINDOW DEICER SWITCH

B

6.INSPECT HWD NO. 3 RELAY

C

9.INSPECT HWD NO. 1 RELAY

D

15.INSPECT HWD NO. 2 RELAY
3.INSPECT FRONT WINDOW DEICER SWITCH
a.

Remove the front window deicer switch.

Click hereVehicle Exterior>WINDOW / GLASS>WINDSHIELD DEICER SWITCH>REMOVAL


b.

Inspect the front window deicer switch.

Click hereVehicle Exterior>WINDOW / GLASS>WINDSHIELD DEICER SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK WIRE HARNESS AND CONNECTOR (FRONT WINDOW DEICER SWITCH - IG POWER SUPPLY)

NG

REPLACE FRONT WINDOW DEICER SWITCH

4.CHECK WIRE HARNESS AND CONNECTOR (FRONT WINDOW DEICER SWITCH - IG POWER SUPPLY)
a.

Disconnect the K148 front window deicer switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K148-5 (IG) - Body ground Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK WIRE HARNESS AND CONNECTOR (FRONT WINDOW DEICER SWITCH - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WIRE HARNESS AND CONNECTOR (FRONT WINDOW DEICER SWITCH - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the K54 and K55 air conditioning amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K148-4 (D) - K54-22 (IND) Always Below 1 Ω
K148-4 (D) or K54-22 (IND) - Body ground Always 10 kΩ or higher
K148-2 (E) - K55-29 (DFAC) Always Below 1 Ω
K148-2 (E) or K55-29 (DFAC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT HWD NO. 3 RELAY
a.

Inspect the HWD NO. 3 relay.

Click hereVehicle Exterior>WINDOW / GLASS>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 3 RELAY - IG POWER SUPPLY)

NG

REPLACE HWD NO. 3 RELAY

7.CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 3 RELAY - IG POWER SUPPLY)
a.
B510527C01
2.323,0.542 2.583,0.771 0.26,0.229 10 false *a
*a HWD No. 3 Relay Holder


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
HWD NO. 3 relay holder terminal 1 - Body ground Engine switch on (IG) 11 to 14 V
HWD NO. 3 relay holder terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 3 RELAY - HWD NO. 1 RELAY OR HWD NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 3 RELAY - HWD NO. 1 RELAY OR HWD NO. 2 RELAY)
a.
B508394C02
0.229,0.229 0.542,0.385 0.313,0.156 10 false *a 2.365,2.031 2.677,2.188 0.313,0.156 10 false *b 2.344,0.594 2.656,0.75 0.313,0.156 10 false *c
*a HWD No. 1 Relay Holder
*b HWD No. 2 Relay Holder
*c HWD No. 3 Relay Holder


Disconnect K54 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD NO. 3 relay holder terminal 3 - HWD NO. 1 relay holder terminal 2 or HWD NO. 2 relay holder terminal 2 Always Below 1 Ω
HWD NO. 3 relay holder terminal 3 - Body ground Always 10 kΩ higher
HWD NO. 1 relay holder terminal 2 - Body ground Always 10 kΩ higher
HWD NO. 2 relay holder terminal 2 - Body ground Always 10 kΩ higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT HWD NO. 1 RELAY
a.

Inspect the HWD NO. 1 relay.

Click hereVehicle Exterior>WINDOW / GLASS>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 1 RELAY - BATTERY)

NG

REPLACE HWD NO. 1 RELAY

10.CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 1 RELAY - BATTERY)
a.
B510528C01
0.229,0.25 0.542,0.542 0.313,0.292 10 false *a
*a HWD No. 1 Relay Holder


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
HWD NO. 1 relay holder terminal 3 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 1 RELAY - HWD NO. 3 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 1 RELAY - HWD NO. 3 RELAY)
B510529C01
0.208,0.25 0.51,0.563 0.302,0.313 10 false *a 2.344,0.573 2.677,0.885 0.333,0.313 10 false *b
*a HWD No. 1 Relay Holder
*b HWD No. 3 Relay Holder


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD NO. 3 relay holder terminal 3 - HWD NO. 1 relay holder terminal 2 Always Below 1 Ω
HWD NO. 3 relay holder terminal 3 or HWD NO. 1 relay holder terminal 2 - Body ground Always 10 kΩ higher



Result:
Proceed to
OK
NG



OK

12.CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 1 RELAY - BODY GROUND)
a.
B510528C01
0.229,0.25 0.542,0.542 0.313,0.292 10 false *a
*a HWD No. 1 Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD NO. 1 relay holder terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 1 RELAY - NO. 1 HEATED WINDSHIELD DEFROSTER (WINDSHIELD GLASS))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 1 RELAY - NO. 1 HEATED WINDSHIELD DEFROSTER (WINDSHIELD GLASS))
a.
B510528C01
0.229,0.25 0.542,0.542 0.313,0.292 10 false *a
*a HWD No. 1 Relay Holder


Disconnect A80 No. 1 heated windshield defroster (windshield glass) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD NO. 1 relay holder terminal 5 - A80-2 (B) Always Below 1 Ω
HWD NO. 1 relay holder terminal 5 or A80-2 (B) - Body ground Always 10 kΩ higher



Result:
Proceed to
OK
NG



OK

14.CHECK WIRE HARNESS AND CONNECTOR (NO. 1 HEATED WINDSHIELD DEFROSTER (WINDSHIELD GLASS) - BODY GROUND)

NG

REPLACE HARNESS OR CONNECTOR

14.CHECK WIRE HARNESS AND CONNECTOR (NO. 1 HEATED WINDSHIELD DEFROSTER (WINDSHIELD GLASS) - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A80-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD GLASS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.INSPECT HWD NO. 2 RELAY
a.

Inspect the HWD NO. 2 relay.

Click hereVehicle Exterior>WINDOW / GLASS>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

16.CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 2 RELAY - BATTERY)

NG

REPLACE HWD NO. 2 RELAY

16.CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 2 RELAY - BATTERY)
a.
B511027C01
2.323,2.031 2.646,2.323 0.323,0.292 10 false *a
*a HWD No. 2 Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
HWD NO. 2 relay holder terminal 3 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

17.CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 2 RELAY - HWD NO. 3 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 2 RELAY - HWD NO. 3 RELAY)
a.
B511028C01
2.302,2.042 2.604,2.313 0.302,0.271 10 false *a 2.302,0.563 2.615,0.813 0.313,0.25 10 false *b
*a HWD No. 2 Relay Holder
*b HWD No. 3 Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD NO. 3 relay holder terminal 3 - HWD NO. 2 relay holder terminal 2 Always Below 1 Ω
HWD NO. 3 relay holder terminal 3 or HWD NO. 2 relay holder terminal 2 - Body ground Always 10 kΩ higher



Result:
Proceed to
OK
NG



OK

18.CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 2 RELAY - BODY GROUND)
a.
B511027C01
2.323,2.031 2.646,2.323 0.323,0.292 10 false *a
*a HWD No. 2 Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD NO. 2 relay holder terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

19.CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 2 RELAY - NO. 2 HEATED WINDSHIELD DEFROSTER (WINDSHIELD GLASS))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK WIRE HARNESS AND CONNECTOR (HWD NO. 2 RELAY - NO. 2 HEATED WINDSHIELD DEFROSTER (WINDSHIELD GLASS))
a.
B511027C01
2.323,2.031 2.646,2.323 0.323,0.292 10 false *a
*a HWD No. 2 Relay Holder


Disconnect A81 No. 2 heated windshield defroster (windshield glass) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD NO. 2 relay holder terminal 5 - A81-2 (B) Always Below 1 Ω
HWD NO. 2 relay holder terminal 5 or A81-2 (B) - Body ground Always 10 kΩ higher



Result:
Proceed to
OK
NG



OK

20.CHECK WIRE HARNESS AND CONNECTOR (NO. 2 HEATED WINDSHIELD DEFROSTER (WINDSHIELD GLASS) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK WIRE HARNESS AND CONNECTOR (NO. 2 HEATED WINDSHIELD DEFROSTER (WINDSHIELD GLASS) - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A81-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD GLASS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR