The outer mirror switch assembly sends the auto retractable outer mirror switch signal to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) sends the auto retract/return signal to the outer mirror control ECU assemblies via CAN communication, which then controls the mirrors.
When the outer mirror control ECU assemblies receive a door lock output signal from the main body ECU (multiplex network body ECU) while the auto retractable outer mirror switch is on, the outer mirror control ECU assemblies operate the retract motors built into the outer rear view mirror assemblies to retract or return the outer rear view mirror assemblies.
The power mirror control system (w/ Memory) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system (w/ Memory) after confirming that the communication systems are functioning properly.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Check the power retract mirror function.
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Memory)>OPERATION CHECK
Power retract mirror function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the power door lock control system.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Power door lock control system is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check the wireless door lock control system.
Wireless door lock control system is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the smart entry and start system (for Entry Function).
Smart entry and start system (for Entry Function) is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Auto Mirror SW | Retractable outer mirror switch signal | OFF or ON | OFF: Retractable outer mirror switch not in auto position
ON: Retractable outer mirror switch in auto position |
- |
| Tester Display |
|---|
| Auto Mirror SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer mirror switch assembly.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL
Inspect the outer mirror switch assembly.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O19 outer mirror switch assembly.
Disconnect the K53 main body ECU (multiplex network body ECU).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O19-11 (MR) - K53-16 (RET) | Always | Below 1 Ω |
| O19-11 (MR) or K53-16 (RET) - Body ground | Always | 10 kΩ or higher |
| O19-17 (MAT) - K53-6 (AMR) | Always | Below 1 Ω |
| O19-17 (MAT) or K53-6 (AMR) - Body ground | Always | 10 kΩ or higher |
| O19-18 (E2) - K53-9 (MIRE) | Always | Below 1 Ω |
| O19-18 (E2) or K53-9 (MIRE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG