Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › 2018.04–2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0351447 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1622  Open or Short Circuit in Back Camera Signal  


DESCRIPTION

DTC C1622 is stored if the television camera controller judges as a result of its self check that the signals or signal lines between the television camera controller and the rear television camera assembly are not normal.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C1622 Open or Short Circuit in Back Camera Signal Open or short in the rear television camera signal circuit
·

Harness or connector

·

Rear television camera assembly

·

Television camera controller


Circumference Monitoring Camera Control Module

WIRING DIAGRAM

E366794E04
4.865,2.521 7.135,2.771 2.271,0.25 10 false Rear Television Camera Assembly 0.396,2.542 2.771,2.844 2.375,0.302 10 false Television Camera Controller 1.427,1.146 1.677,1.354 0.25,0.208 10 false 1 1.427,1.542 1.677,1.75 0.25,0.208 10 false 2 1.427,1.906 1.677,2.115 0.25,0.208 10 false 9 5.479,1.156 5.729,1.365 0.25,0.208 10 false 3 5.469,0.427 5.719,0.635 0.25,0.208 10 false 6 5.521,1.521 5.771,1.729 0.25,0.208 10 false 2 5.51,1.896 5.76,2.104 0.25,0.208 10 false 5 0.927,2.01 1.417,2.24 0.49,0.229 10 false CGND 1.094,1.635 1.583,1.865 0.49,0.229 10 false CV- 1.063,1.26 1.552,1.49 0.49,0.229 10 false CV+ 0.302,0.49 1.5,0.708 1.198,0.219 10 false from ACC Relay 3.219,0.677 4.417,0.896 1.198,0.219 10 false ECU-ACC 4.865,2.365 6.104,2.594 1.24,0.229 10 false m4 5.698,0.51 6.094,0.719 0.396,0.208 10 false CB+ 5.708,1.26 6.104,1.469 0.396,0.208 10 false CV+ 5.698,1.615 6.094,1.823 0.396,0.208 10 false CV- 5.708,2.01 6.198,2.24 0.49,0.229 10 false CGND 3.427,3.385 5.698,3.635 2.271,0.25 10 false *: Shielded 3.469,1.823 4.198,2.083 0.729,0.26 10 false * 0.396,2.375 0.885,2.604 0.49,0.229 10 false R124

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the R124 television camera controller connector.


b.

Disconnect the m4 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R124-1 (CV+) - m4-3 (CV+) Always Below 1 Ω
R124-2 (CV-) - m4-2 (CV-) Always Below 1 Ω
R124-9 (CGND) - m4-5 (CGND) Always Below 1 Ω
R124-1 (CV+) or m4-3 (CV+) - Body ground Always 10 kΩ or higher
R124-2 (CV-) or m4-2 (CV-) - Body ground Always 10 kΩ or higher
R124-9 (CGND) or m4-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ACC POWER SUPPLY - GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ACC POWER SUPPLY - GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
m4-6 (CB+) - Body ground Engine switch on (ACC) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK TELEVISION CAMERA CONTROLLER (CV-, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TELEVISION CAMERA CONTROLLER (CV-, CGND)
a.

Disconnect the R124 television camera controller connector.


b.
E181084C22
2.458,1.75 2.75,2.625 true 2.323,2.021 2.073,2.688 true 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 1.906,2.719 2.323,2.885 0.417,0.167 10 false CGND 2.698,2.667 3.031,2.833 0.333,0.167 10 false CV-
*a Component without harness connected
(Television Camera Controller)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (CV-) - Body ground Always Below 1 Ω
9 (CGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK REAR TELEVISION CAMERA ASSEMBLY (CV+, CGND)

NG

4.CHECK REAR TELEVISION CAMERA ASSEMBLY (CV+, CGND)
a.

Remove the television camera controller with the connector still connected.


b.

Using an oscilloscope, check the waveform of the rear television camera assembly.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the television camera controller with the connector connected.


E395393C01
1.25,0.365 1.74,0.594 0.49,0.229 5.792,1.656 5.948,2.365 5.948,2.365 6.104,2.365 false 2.052,1.5 2.208,2.208 2.208,2.208 2.365,2.208 true 3.563,1.771 3.719,2.479 3.719,2.479 3.875,2.479 false 2.25,1.313 2.427,0.646 2.427,0.646 2.583,0.646 true 5.677,1.677 5.552,2.448 5.552,2.448 5.375,2.448 false 3.448,1.813 3.323,2.583 3.323,2.583 3.146,2.583 false 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 3.156,0.427 3.469,0.583 0.313,0.156 10 false *b 5.313,0.417 5.625,0.573 0.313,0.156 10 false *c 5.219,2.354 5.531,2.51 0.313,0.156 10 false *d 3.917,2.385 4.229,2.542 0.313,0.156 10 false *e 2.979,2.49 3.292,2.646 0.313,0.156 10 false *d 6.135,2.292 6.448,2.448 0.313,0.156 10 false *e 1.333,0.396 1.698,0.594 0.365,0.198 10 false R124 2.625,0.563 2.99,0.76 0.365,0.198 10 false CV+ 2.417,2.135 2.99,2.344 0.573,0.208 10 false CGND 2.698,1.302 3.271,1.51 0.573,0.208 10 false GND 4.833,1.292 5.406,1.5 0.573,0.208 10 false GND
*a Component with harness connected
(Television Camera Controller)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).



Measurement Condition
Item Content
Terminal No. (Symbol) R124-1 (CV+) - R124-9 (CGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Engine switch on (IG), panoramic view monitor system operating

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG