Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › 2018.04–2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0351447 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1682  Front Camera Current Malfunction  


DESCRIPTION

DTC C1682 is stored if the television camera controller judges as a result of its self check that there is a problem with the current supplied from the front television camera assembly connected to the television camera controller.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C1682 Front Camera Current Malfunction Open or short in the front television camera signal circuit
·

Harness or connector

·

Front television camera assembly

·

Television camera controller


Circumference Monitoring Camera Control Module

WIRING DIAGRAM

E372777E10
1.51,0.698 2.427,0.896 0.917,0.198 10 false BCB+ 1.49,1.188 2.406,1.385 0.917,0.198 10 false BGND 5.271,0.708 6.188,0.906 0.917,0.198 10 false BCB+ 5.292,1.177 6.208,1.375 0.917,0.198 10 false BGND 5.094,1.698 6.01,1.896 0.917,0.198 10 false R124 5.083,1.854 6.875,2.188 1.792,0.333 10 false Television Camera Controller 0.542,1.688 1.458,1.885 0.917,0.198 10 false B7 0.542,1.854 3.24,2.083 2.698,0.229 10 false Front Television Camera Assembly 1.979,0.594 2.375,0.833 0.396,0.24 10 false 6 1.979,1.073 2.375,1.313 0.396,0.24 10 false 5 5.01,0.594 5.406,0.833 0.396,0.24 10 false 15 5.021,1.083 5.417,1.323 0.396,0.24 10 false 27

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - FRONT TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the R124 television camera controller connector.


b.

Disconnect the B7 front television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R124-15 (BCB+) - B7-6 (BCB+) Always Below 1 Ω
R124-27 (BGND) - B7-5 (BGND) Always Below 1 Ω
R124-15 (BCB+) or B7-6 (BCB+) - Body ground Always 10 kΩ or higher
R124-27 (BGND) or B7-5 (BGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK TELEVISION CAMERA CONTROLLER (BCB+, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TELEVISION CAMERA CONTROLLER (BCB+, BGND)
a.
E394317C07
1.479,0.219 1.906,0.458 0.427,0.24 1.323,1.188 0.896,0.417 0.896,0.417 0.74,0.417 true 1.323,1.385 1.031,1.865 1.031,1.865 0.823,1.865 true 0.146,0.104 0.438,0.406 0.292,0.302 10 false *a 0.354,0.302 0.927,0.552 0.573,0.25 10 false BCB+ 0.406,1.771 0.979,2.021 0.573,0.25 10 false BGND 1.542,0.25 2.115,0.5 0.573,0.25 10 false R124
*a Component with harness connected
(Television Camera Controller)


Remove the television camera controller with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R124-27 (BGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R124-15 (BCB+) - R124-27 (BGND) Engine switch on (ACC) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

NG