Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › 2018.04–2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0351447 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1683  Side Camera Feedback Malfunction  


DESCRIPTION

This DTC is stored if the television camera controller judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the passenger side television camera assembly to the television camera controller.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C1683 Side Camera Feedback Malfunction Side camera feedback malfunction
·

Harness or connector

·

Television camera controller

·

Side television camera assembly RH

·

Outer rear view mirror assembly with cover RH


Circumference Monitoring Camera Control Module

WIRING DIAGRAM

E372778E10
0.313,2.583 1.771,3.146 1.458,0.563 10 false Side Television Camera Assembly RH 3.438,0.656 4.354,0.854 0.917,0.198 10 false RCB+ 3.469,1.052 4.385,1.25 0.917,0.198 10 false RCV- 3.448,1.448 4.365,1.646 0.917,0.198 10 false RCV+ 3.417,1.844 4.333,2.042 0.917,0.198 10 false RGND 3.417,2.24 4.333,2.438 0.917,0.198 10 false SGND 5.729,0.646 6.646,0.844 0.917,0.198 10 false RCB+ 5.74,1.042 6.656,1.24 0.917,0.198 10 false RCV- 5.74,1.458 6.656,1.656 0.917,0.198 10 false RCV+ 5.729,1.823 6.646,2.021 0.917,0.198 10 false RGND 5.719,2.24 6.635,2.438 0.917,0.198 10 false SGND 4.406,3.24 5.323,3.438 0.917,0.198 10 false *: Shielded 5.521,2.698 6.667,3.344 1.146,0.646 10 false Television Camera Controller 2.74,2.719 4.302,3.146 1.563,0.427 10 false Outer Rear View Mirror Assembly with Cover RH 2.75,2.563 3.281,2.781 0.531,0.219 10 false N24 5.531,2.542 6.042,2.76 0.51,0.219 10 false R124 4.74,1.979 5.271,2.198 0.531,0.219 10 false * 3.917,0.531 4.448,0.75 0.531,0.219 10 false 2 3.906,0.917 4.438,1.135 0.531,0.219 10 false 12 3.917,1.344 4.448,1.563 0.531,0.219 10 false 1 3.906,1.719 4.438,1.938 0.531,0.219 10 false 13 3.906,2.115 4.438,2.333 0.531,0.219 10 false 14 5.521,0.563 6.052,0.781 0.531,0.219 10 false 6 5.542,0.938 6.073,1.156 0.531,0.219 10 false 5 5.542,1.344 6.073,1.563 0.531,0.219 10 false 4 5.469,1.719 6,1.938 0.531,0.219 10 false 18 5.469,2.125 6,2.344 0.531,0.219 10 false 16

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Panoramic View Monitor > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Panoramic View Monitor > Trouble Codes
50001 353
OK:

DTC C1683 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER RH)
2.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA CONTROLLER - OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER RH)
a.

Disconnect the R124 television camera controller connector.


b.

Disconnect the N24 outer rear view mirror assembly with cover RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R124-6 (RCB+) - N24-2 (RCB+) Always Below 1 Ω
R124-4 (RCV+) - N24-1 (RCV+) Always Below 1 Ω
R124-5 (RCV-) - N24-12 (RCV-) Always Below 1 Ω
R124-18 (RGND) - N24-13 (RGND) Always Below 1 Ω
R124-16 (SGND) - N24-14 (SGND) Always Below 1 Ω
R124-6 (RCB+) or N24-2 (RCB+) - Body ground Always 10 kΩ or higher
R124-4 (RCV+) or N24-1 (RCV+) - Body ground Always 10 kΩ or higher
R124-5 (RCV-) or N24-12 (RCV-) - Body ground Always 10 kΩ or higher
R124-18 (RGND) or N24-13 (RGND) - Body ground Always 10 kΩ or higher
R124-16 (SGND) or N24-14 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TELEVISION CAMERA CONTROLLER (RCV-, RGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TELEVISION CAMERA CONTROLLER (RCV-, RGND)
a.

Disconnect the R124 television camera controller connector.


b.
E181084C21
0.896,1.688 1.167,1.198 true 0.74,2 0.49,2.667 true 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 0.344,2.75 0.76,2.917 0.417,0.167 10 false RGND 1.177,1.073 1.635,1.24 0.458,0.167 10 false RCV-
*a Component without harness connected
(Television Camera Controller)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
18 (RGND) - Body ground Always Below 1 Ω
5 (RCV-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK TELEVISION CAMERA CONTROLLER (RCB+, RGND)

NG

4.CHECK TELEVISION CAMERA CONTROLLER (RCB+, RGND)
a.
E394317C09
1.479,0.219 1.906,0.458 0.427,0.24 0.844,1.031 0.573,0.458 0.573,0.458 0.417,0.458 true 0.844,1.271 0.938,1.958 0.938,1.958 1.094,1.958 true 0.146,0.104 0.438,0.406 0.292,0.302 10 false *a 0.042,0.354 0.615,0.604 0.573,0.25 10 false RCB+ 1.135,1.865 1.708,2.115 0.573,0.25 10 false RGND 1.563,0.24 2.135,0.49 0.573,0.25 10 false R124
*a Component with harness connected
(Television Camera Controller)


Remove the television camera controller with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R124-18 (RGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R124-6 (RCB+) - R124-18 (RGND) Engine switch on (ACC) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

5.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH (RCV+, RGND)

NG

5.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH (RCV+, RGND)
a.

Remove the television camera controller with the connector still connected.


b.

Using an oscilloscope, check the waveform of the side television camera assembly RH.

HINT:

A waterproof connector is used for the side television camera assembly RH. Therefore, inspect the waveform at the television camera controller with the connector connected.


E395393C03
1.25,0.365 1.74,0.594 0.49,0.229 5.792,1.656 5.948,2.365 5.948,2.365 6.104,2.365 false 0.979,1.354 1.24,2.458 1.24,2.458 1.396,2.458 true 3.563,1.771 3.719,2.479 3.719,2.479 3.875,2.479 false 5.677,1.677 5.552,2.448 5.552,2.448 5.375,2.448 false 3.448,1.813 3.323,2.583 3.323,2.583 3.146,2.583 false 0.771,1.51 0.688,2.323 0.688,2.323 0.51,2.323 true 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 3.156,0.427 3.469,0.583 0.313,0.156 10 false *b 5.313,0.417 5.625,0.573 0.313,0.156 10 false *c 5.219,2.354 5.531,2.51 0.313,0.156 10 false *d 3.917,2.385 4.229,2.542 0.313,0.156 10 false *e 2.979,2.49 3.292,2.646 0.313,0.156 10 false *d 6.135,2.292 6.448,2.448 0.313,0.156 10 false *e 1.333,0.396 1.698,0.594 0.365,0.198 10 false R124 1.427,2.375 1.927,2.615 0.5,0.24 10 false RCV+ 0.094,2.24 0.667,2.448 0.573,0.208 10 false RGND 2.698,1.302 3.271,1.51 0.573,0.208 10 false GND 4.833,1.292 5.406,1.5 0.573,0.208 10 false GND
*a Component with harness connected
(Television Camera Controller)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


HINT:
·

The video waveform changes according to the image sent by the side television camera assembly RH.

·

The video waveform is constantly output when the engine switch is on (ACC).



Measurement Condition
Item Content
Tester Connection R124-4 (RCV+) - R124-18 (RGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Engine switch on (IG), panoramic view monitor system operating

OK:

Waveform is similar to that shown in illustration.



Result:
Proceed to
OK
NG



OK

NG

6.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH
6.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH
a.

Replace the side television camera assembly RH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Panoramic View Monitor > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Panoramic View Monitor > Trouble Codes
50001 353
OK:

DTC C1683 is not output.



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY RH IS DEFECTIVE)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER RH