Home › Engine / Hybrid System › 6AR-FSE (ENGINE CONTROL) › SFI SYSTEM › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072203 6AR-FSE ENGINE CONTROL _0351507 SFI SYSTEM C

6AR-FSE ENGINE CONTROL  SFI SYSTEM  P042000  Catalyst System Efficiency Below Threshold Bank 1  


MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.

The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.

In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the voltage output of the heated oxygen sensor while performing active air fuel ratio control.

The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 30 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the cycle of the waveform for the heated oxygen sensor is long, the oxygen storage capacity is great. There is a direct correlation between the heated oxygen sensor and the oxygen storage capacity of the three-way catalytic converter.

The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, the ECM will illuminate the MIL and store a DTC.

This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P042000 Catalyst System Efficiency Below Threshold Bank 1 The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic).
·

Gas leak from exhaust system

·

Air fuel ratio sensor

·

Heated oxygen sensor

·

Exhaust manifold (TWC: Front catalyst)

·

Front exhaust pipe assembly (TWC: Rear catalyst)

·

EGR valve assembly


Comes on DTC stored SAE Code:
P0420

CATALYST LOCATION

A421384C01
6.104,0.76 5.938,0.427 5.938,0.427 5.688,0.427 true 5.417,1.917 5.667,2.25 5.667,2.25 5.917,2.25 true 2.75,3.479 3,3.813 3,3.813 3.25,3.813 true 2.333,3.99 2.583,4.323 2.583,4.323 2.833,4.323 true 1.781,2.542 2.198,2.292 2.198,2.292 2.448,2.292 true 1.354,2.073 1.688,1.323 1.688,1.323 1.938,1.323 true 0.75,1.406 0.833,1.073 0.833,1.073 1.083,1.073 true 0.708,2.24 0.792,2.323 0.792,2.323 0.875,2.323 true 1.969,1.229 2.281,1.385 0.313,0.156 10 false *1 2.479,2.208 2.792,2.365 0.313,0.156 10 false *2 1.104,0.99 1.417,1.146 0.313,0.156 10 false *3 2.854,4.24 3.167,4.396 0.313,0.156 10 false *4 5.948,2.167 6.26,2.323 0.313,0.156 10 false *5 5.51,0.333 5.823,0.49 0.313,0.156 10 false *6 0.896,2.24 1.208,2.396 0.313,0.156 10 false *7 3.271,3.729 3.583,3.885 0.313,0.156 10 false *8
*1 Air Fuel Ratio Sensor *2 Heated Oxygen Sensor
*3 Exhaust Manifold Converter Sub-assembly *4 Front Exhaust Pipe Assembly
*5 Center Exhaust Pipe Assembly *6 Tail Exhaust Pipe Assembly
*7 TWC: Front Catalyst *8 TWC: Rear Catalyst


NOTICE:

Replace the exhaust manifold converter sub-assembly (*3) and the front exhaust pipe assembly (*4) together when catalyst replacement is necessary. (Excluding air fuel ratio sensor*1 and heated oxygen sensor*2)


MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor
Heated oxygen sensor
Required Sensors/Components (Related) Intake air temperature sensor
Mass air flow meter sub-assembly
Crank position sensor
Engine coolant temperature sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Battery voltage 11 V or higher
Intake air temperature -10°C (14°F) or higher
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [11 psi(abs)] or higher
Idling Off
Engine speed Less than 4000 rpm
Air fuel ratio sensor status Activated
Fuel system status Closed loop
Engine load 10% or higher, and less than 90%
All of the following conditions are met -
Mass air flow rate 2.5 gm/sec or more, and less than 45 gm/sec
Front catalyst temperature (estimated) 556°C (1032°F) or higher, and less than 840°C (1544°F)
Rear catalyst temperature (estimated) 415°C (779°F) or higher, and less than 770°C (1418°F)

CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.


A387619E12
1.333,0.865 1.698,0.469 1.698,0.469 1.854,0.469 false 0.729,1.146 1.385,1.406 0.656,0.26 10 false 60 km/h 0.938,2.208 1.406,2.458 0.469,0.25 10 false Idling 0.188,2.458 1.385,2.74 1.198,0.281 10 false Engine Switch off 0.146,3.438 4.74,3.74 4.594,0.302 10 false *: Drive the vehicle while keeping the engine load as constant as possible 1.906,0.385 3.552,0.698 1.646,0.313 10 false Between 75 to 100 km/h 1.677,2.104 1.948,2.344 0.271,0.24 10 false [A] 1.51,2.719 2.083,3.115 0.573,0.396 10 false Warming up 2.615,1.021 2.938,1.281 0.323,0.26 10 false [B]* 2.365,2.75 3.083,3.104 0.719,0.354 10 false 10 minutes or more 3.146,3.135 3.448,3.396 0.302,0.26 10 false [C] 3.49,2.115 3.781,2.365 0.292,0.25 10 false [D] 3.375,2.719 3.99,3.073 0.615,0.354 10 false Warming up 4.406,1.052 4.74,1.323 0.333,0.271 10 false [E]* 4.135,2.76 4.844,3.177 0.708,0.417 10 false 10 minutes or more 5.01,3.146 5.313,3.417 0.302,0.271 10 false [F] 6.167,0.656 6.531,0.938 0.365,0.281 10 false [G]* 5.906,2.719 6.635,3.25 0.729,0.531 10 false 10 minutes or more 6.771,3.125 7.021,3.365 0.25,0.24 10 false [H] 0.344,0.125 1.302,0.354 0.958,0.229 10 false Vehicle Speed

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Turn the engine switch on (IG).

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

9.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


10.

Turn the engine switch off and wait for at least 30 seconds [C].

11.

Turn the engine switch on (IG).

12.

Turn the GTS on.

13.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [D].

14.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


15.

Enter the following menus: Powertrain / Engine / Trouble Codes [F].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

18.

Input the DTC: P042000.

19.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE and no pending DTC is output, perform the following procedure.



20.

Drive the vehicle at a speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes or more [G].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


21.

Enter the following menus: Powertrain / Engine / Trouble Codes [H].

22.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



23.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

24.

Input the DTC: P042000.

25.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CONDITIONING FOR SENSOR TESTING

HINT:

Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is to activate the sensors sufficiently to obtain appropriate inspection results.


A270243E50
4.865,3.094 5.01,3.427 5.01,3.427 5.167,3.083 false 3.615,0.875 3.844,1.073 0.229,0.198 10 false [B] 0.615,0.563 1.698,0.76 1.083,0.198 10 false Engine Speed 0.813,0.979 1.615,1.177 0.802,0.198 10 false 3000 rpm 0.813,1.51 1.615,1.708 0.802,0.198 10 false 2000 rpm 1.115,2.531 1.563,2.729 0.448,0.198 10 false Idling 0.354,2.76 1.531,2.958 1.177,0.198 10 false Engine Switch off 2.073,2.385 2.302,2.583 0.229,0.198 10 false [A] 4.792,0.875 5.021,1.073 0.229,0.198 10 false [C] 5.094,1.396 5.323,1.594 0.229,0.198 10 false [C] 2.104,3.125 3.021,3.323 0.917,0.198 10 false Warming up 3.365,3.125 4.542,3.323 1.177,0.198 10 false At least 3 minutes 4.698,3.479 5.51,3.677 0.813,0.198 10 false 2 seconds 6.573,2.885 6.969,3.083 0.396,0.198 10 false Time

(a) Connect the GTS to the DLC3.

(b) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes [A].

(c) Turn the GTS on.

(d) Enter the following menus: Powertrain / Engine / Data List / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.

(e) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes [B].

(f) While running the engine at 3000 rpm for 2 seconds, and then 2000 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the GTS [C].


HINT:
·

If the voltage output of either the air fuel ratio or heated oxygen sensor does not fluctuate, or there is a noise in the waveform of either sensor, the sensor may be malfunctioning.

·

If the voltage outputs of both the sensors remain lean or rich, the air fuel ratio may be extremely lean or rich. In such cases, perform the Control the Injection Volume for A/F Sensor Active Test using the GTS.

·

If the Three-way Catalytic Converter (TWC) has deteriorated, the heated oxygen sensor (located behind the Three-way Catalytic Converter [TWC]) voltage output fluctuates up and down frequently, even under normal driving conditions (active air fuel ratio control is not performed).


A199479E21
0.25,0.104 4.594,0.271 4.344,0.167 10 Voltage Output When Active Air Fuel Ratio Control Not Performed: 2.438,0.531 3.573,0.698 1.135,0.167 10 Normal Catalyst 4.76,0.542 6.135,0.729 1.375,0.188 10 Deteriorated Catalyst 2.406,2.99 3.281,3.188 0.875,0.198 10 10 seconds 4.958,3 5.792,3.167 0.833,0.167 10 10 seconds 1.49,0.781 1.875,0.927 0.385,0.146 10 3.4 V 1.479,1.208 1.865,1.354 0.385,0.146 10 3.1 V 1.49,2.052 1.885,2.26 0.396,0.208 10 1.0 V 1.604,2.729 1.917,2.958 0.313,0.229 10 0 V 0.052,2.198 1.323,2.896 1.271,0.698 10 Waveform of Heated Oxygen Sensor Behind Three-Way Catalytic Converter 0.063,0.76 1.396,1.417 1.333,0.656 10 Waveform of Air Fuel Ratio Sensor in Front of Three-Way Catalytic Converter


CAUTION / NOTICE / HINT

HINT:
·

If a malfunction cannot be found when troubleshooting DTC P042000, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P017100 (System Too Lean) and P017200 (System Too Rich).

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P042000)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P042000 is output A
DTC P042000 and other DTCs are output B


HINT:

If any DTCs other than P042000 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.


e.

Warm up the air fuel ratio sensors at an engine speed of 2500 rpm for 90 seconds.


f.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / Coolant Temperature, A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
Coolant Temperature
A/F (O2) Sensor Voltage B1S1
O2 Sensor Voltage B1S2
50004 372 8 205,225,218

g.

Change the fuel injection volume using the GTS, and monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2) displayed on the GTS.

HINT:
·

The Active Test "Control the Injection Volume for A/F Sensor" can be used to lower the fuel injection volume by 12.5% or increase the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard:
GTS Display
(Sensor)
Injection Volume Status Voltage
A/F (O2) Sensor Voltage B1S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2 Sensor Voltage B1S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V


Result:
Status of A/F (O2) Sensor Voltage B1S1 Status of O2 Sensor Voltage B1S2 Actual air fuel ratio, air fuel ratio sensor and heated oxygen sensor condition Main Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal
·

Three-way catalytic converter

·

Gas leak from exhaust system

·

EGR valve assembly


A
Lean Lean/Rich Air fuel ratio sensor malfunction
·

Air fuel ratio sensor


B
Rich Lean/Rich Air fuel ratio sensor malfunction
·

Air fuel ratio sensor


Lean/Rich Lean Heated oxygen sensor malfunction
·

Heated oxygen sensor

·

Gas leak from exhaust system


C
Lean/Rich Rich Heated oxygen sensor malfunction
·

Heated oxygen sensor

·

Gas leak from exhaust system


Lean Lean Actual air fuel ratio lean
·

Extremely lean actual air fuel ratio

·

Gas leak from exhaust system

·

EGR valve assembly


D
Rich Rich Actual air fuel ratio rich
·

Extremely rich actual air fuel ratio

·

Gas leak from exhaust system

·

EGR valve assembly




Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (A/F (O2) Sensor Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2 Sensor Voltage B1S2) is consistently below 0.4 V.

Rich: During Control the Injection Volume for A/F Sensor, the A/F (O2) Sensor Voltage B1S1 is consistently below 3.1 V, and the O2 Sensor Voltage B1S2 is consistently higher than 0.55 V.

Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the air fuel ratio sensor or heated oxygen sensor alternates correctly.


HINT:

Refer to "Data List / Active Test" [A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2].

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST




A

3.CHECK FOR EXHAUST GAS LEAK

B

6.REPLACE AIR FUEL RATIO SENSOR

C

7.CHECK FOR EXHAUST GAS LEAK

D

9.CHECK FOR EXHAUST GAS LEAK
3.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks in exhaust system.



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

13.REPAIR OR REPLACE EXHAUST SYSTEM
4.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



e.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / Engine Speed, Intake Manifold Absolute Pressure and Coolant Temperature.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Engine Speed
Intake Manifold Absolute Pressure
Coolant Temperature
50004 372 25 211,385,205

f.

Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.

NOTICE:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

The value of Intake Manifold Absolute Pressure and Engine Speed change in response to EGR step position.


Standard:
- Control the EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stalls
Intake Manifold Absolute Pressure
(Data List)
Intake Manifold Absolute Pressure value is 20 to 40 kPa(abs)
(2.9 to 5.8 psi(abs))
(EGR valve is fully closed)
Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed


HINT:

During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.



Result:
Proceed to
OK
NG



OK

16.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

NG

5.INSPECT EGR VALVE ASSEMBLY
5.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.



HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

16.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

NG

6.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
7.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks in exhaust system.



Result:
Proceed to
OK
NG



OK

8.REPLACE HEATED OXYGEN SENSOR

NG

13.REPAIR OR REPLACE EXHAUST SYSTEM
8.REPLACE HEATED OXYGEN SENSOR

Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
9.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks in exhaust system.



Result:
Proceed to
OK
NG



OK

10.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

13.REPAIR OR REPLACE EXHAUST SYSTEM
10.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



e.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / Engine Speed, Intake Manifold Absolute Pressure and Coolant Temperature.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Engine Speed
Intake Manifold Absolute Pressure
Coolant Temperature
50004 372 25 211,385,205

f.

Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.

NOTICE:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

The value of Intake Manifold Absolute Pressure and Engine Speed change in response to EGR step position.


Standard:
- Control the EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stalls
Intake Manifold Absolute Pressure
(Data List)
Intake Manifold Absolute Pressure value is 20 to 40 kPa(abs)
(2.9 to 5.8 psi(abs))
(EGR valve is fully closed)
Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed


HINT:

During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.



Result:
Proceed to
OK
NG



OK

12.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO

NG

11.INSPECT EGR VALVE ASSEMBLY
11.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.



HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

12.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO

NG

12.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
a.

Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P017100 and P017200 Inspection Procedure.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>P017100


Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
13.REPAIR OR REPLACE EXHAUST SYSTEM
a.

Repair or replace the exhaust system.

HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

14.CLEAR DTC
14.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the engine switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P042000)
15.CHECK WHETHER DTC OUTPUT RECURS (DTC P042000)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P042000 is output B




A

END

B

16.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)
16.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)
NOTICE:

When replacing the exhaust manifold converter sub-assembly (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.


HINT:

Confirm the replacement parts, referring to the illustration in Catalyst Location.


a.

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst).

Click hereEngine / Hybrid System>6AR-FSE (INTAKE / EXHAUST)>EXHAUST MANIFOLD>COMPONENTS


b.

Replace the front exhaust pipe assembly (TWC: Rear catalyst).

Click hereEngine / Hybrid System>6AR-FSE (INTAKE / EXHAUST)>EXHAUST PIPE>COMPONENTS


Result:
Proceed to
NEXT



NEXT

END