Home › Engine / Hybrid System › 6AR-FSE (ENGINE CONTROL) › SFI SYSTEM › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072203 6AR-FSE ENGINE CONTROL _0351507 SFI SYSTEM C

6AR-FSE ENGINE CONTROL  SFI SYSTEM  P21CF13  Cylinder 1 Injector "B" Circuit Open  P21D013  Cylinder 2 Injector "B" Circuit Open  P21D113  Cylinder 3 Injector "B" Circuit Open  P21D213  Cylinder 4 Injector "B" Circuit Open  


DESCRIPTION

The D-4S system has two injection systems. One is an in-cylinder direct injection system that directly injects pressurized fuel into the combustion chamber. The other is an intake port injection system. The ECM determines the percentage of direct injection and port injection necessary in accordance with the engine speed and load.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P21CF13 Cylinder 1 Injector "B" Circuit Open Current is not applied to the injector 10 times or more (1 trip detection logic).
·

Open or short in port fuel injector assembly circuit

·

Port fuel injector assembly

·

ECM


Comes on DTC stored SAE Code:
P21CF
P21D013 Cylinder 2 Injector "B" Circuit Open Current is not applied to the injector 10 times or more (1 trip detection logic).
·

Open or short in port fuel injector assembly circuit

·

Port fuel injector assembly

·

ECM


Comes on DTC stored SAE Code:
P21D0
P21D113 Cylinder 3 Injector "B" Circuit Open Current is not applied to the injector 10 times or more (1 trip detection logic).
·

Open or short in port fuel injector assembly circuit

·

Port fuel injector assembly

·

ECM


Comes on DTC stored SAE Code:
P21D1
P21D213 Cylinder 4 Injector "B" Circuit Open Current is not applied to the injector 10 times or more (1 trip detection logic).
·

Open or short in port fuel injector assembly circuit

·

Port fuel injector assembly

·

ECM


Comes on DTC stored SAE Code:
P21D2

MONITOR DESCRIPTION

The ECM monitors the injection control of the port fuel injector assemblies. If a malfunction is detected in a port fuel injector assembly circuit, the ECM cancels the injection control for the corresponding cylinder, illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components Port fuel injector assembly (cylinder 1 to 4)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Start the engine.

7.

Idle the engine for 3 minutes or more.

8.

Turn the GTS on.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P21CF13, P21D013, P21D113 or P21D213.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A416699E02
0.542,1.01 1.177,1.219 0.635,0.208 10 false IG2-MAIN 1.344,1.583 1.979,1.792 0.635,0.208 10 false IG2 NO. 1 2.01,0.729 2.25,0.938 0.24,0.208 10 false 3 2.01,1.135 2.25,1.344 0.24,0.208 10 false 1 1.188,0.74 1.427,0.948 0.24,0.208 10 false 5 1.208,1.135 1.448,1.344 0.24,0.208 10 false 2 2.313,1 2.948,1.208 0.635,0.208 10 false INJ 3.979,0.719 4.219,0.927 0.24,0.208 10 false 1 4.667,0.729 4.906,0.938 0.24,0.208 10 false 2 3.594,0.969 4.229,1.177 0.635,0.208 10 false T1 3.594,1.125 5.313,1.521 1.719,0.396 10 false Port Fuel Injector Assembly (No. 1 Cylinder) 5.573,0.729 5.813,0.938 0.24,0.208 10 false 57 5.844,0.729 6.167,0.938 0.323,0.208 10 false #10 5.854,1.729 6.156,1.938 0.302,0.208 10 false #20 5.854,2.75 6.156,2.958 0.302,0.208 10 false #30 5.833,3.75 6.177,3.958 0.344,0.208 10 false #40 5.854,4.76 6.094,4.969 0.24,0.208 10 false E1 5.583,1.74 5.823,1.948 0.24,0.208 10 false 54 5.552,2.74 5.792,2.948 0.24,0.208 10 false 55 5.552,3.75 5.792,3.958 0.24,0.208 10 false 56 5.552,4.76 5.792,4.969 0.24,0.208 10 false 53 4.667,1.729 4.906,1.938 0.24,0.208 10 false 2 4.677,2.74 4.917,2.948 0.24,0.208 10 false 2 4.688,3.74 4.927,3.948 0.24,0.208 10 false 2 3.979,1.74 4.219,1.948 0.24,0.208 10 false 1 3.969,2.75 4.208,2.958 0.24,0.208 10 false 1 3.979,3.75 4.219,3.958 0.24,0.208 10 false 1 3.604,3.188 5.323,3.583 1.719,0.396 10 false Port Fuel Injector Assembly (No. 3 Cylinder) 3.594,2.146 5.313,2.542 1.719,0.396 10 false Port Fuel Injector Assembly (No. 2 Cylinder) 3.573,4.146 5.292,4.542 1.719,0.396 10 false Port Fuel Injector Assembly (No. 4 Cylinder) 3.604,3.01 4.24,3.219 0.635,0.208 10 false T2 3.594,1.969 4.229,2.177 0.635,0.208 10 false T3 3.573,3.99 4.208,4.198 0.635,0.208 10 false T4 6.438,6.063 6.865,6.271 0.427,0.208 10 false ECM 0.927,4.479 2.719,5 1.792,0.521 10 false Certification ECU (Smart Key ECU Assembly) 0.927,4.313 1.563,4.521 0.635,0.208 10 false K62 1.833,3.865 2.469,4.073 0.635,0.208 10 false IG1D 2.24,3.729 2.479,3.938 0.24,0.208 10 false 17 0.396,5.073 1.031,5.281 0.635,0.208 10 false FL MAIN 0.573,6.073 1.208,6.281 0.635,0.208 10 false Battery 6.677,2.969 7.021,3.177 0.344,0.208 10 false IC 6.01,6.063 6.344,6.26 0.333,0.198 10 false C58

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT (DTC P21CF13, P21D013, P21D113 OR P21D213)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P21CF13, P21D013, P21D113 or P21D213 is output A
DTC P21CF13, P21D013, P21D113 and P21D213 are output B




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PORT FUEL INJECTOR ASSEMBLY)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 NO. 1 RELAY - PORT FUEL INJECTOR ASSEMBLY)

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PORT FUEL INJECTOR ASSEMBLY)
A226264C34
0.417,0.5 0.833,0.75 0.417,0.25 0.417,0.833 0.833,1.083 0.417,0.25 0.417,1.167 0.833,1.417 0.417,0.25 0.417,1.5 0.833,1.75 0.417,0.25 0.073,0.115 0.25,0.271 0.177,0.156 10 false *a 0.542,0.531 0.865,0.792 0.323,0.26 10 false T1 0.552,0.865 0.865,1.115 0.313,0.25 10 false T2 0.552,1.208 0.875,1.49 0.323,0.281 10 false T3 0.552,1.542 0.917,1.823 0.365,0.281 10 false T4
*a Front view of wire harness connector
(to Port Fuel Injector Assembly)


a.

Disconnect the port fuel injector assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T1-1 - Body ground Engine switch on (IG) 11 to 14 V
T2-1 - Body ground Engine switch on (IG) 11 to 14 V
T3-1 - Body ground Engine switch on (IG) 11 to 14 V
T4-1 - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PORT FUEL INJECTOR ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 NO. 1 RELAY - PORT FUEL INJECTOR ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (PORT FUEL INJECTOR ASSEMBLY - ECM)
a.

Disconnect the port fuel injector assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T1-2 - C58-57 (#10) Always Below 1 Ω
T3-2 - C58-54 (#20) Always Below 1 Ω
T2-2 - C58-55 (#30) Always Below 1 Ω
T4-2 - C58-56 (#40) Always Below 1 Ω
T1-2 or C58-57 (#10) - Body ground and other terminals Always 10 kΩ or higher
T3-2 or C58-54 (#20) - Body ground and other terminals Always 10 kΩ or higher
T2-2 or C58-55 (#30) - Body ground and other terminals Always 10 kΩ or higher
T4-2 or C58-56 (#40) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT PORT FUEL INJECTOR ASSEMBLY (RESISTANCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT PORT FUEL INJECTOR ASSEMBLY (RESISTANCE)
a.

HINT:

Perform "Inspection After Repair" after replacing the port fuel injector assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

NG