Home › Engine / Hybrid System › 6AR-FSE (FUEL) › FUEL INJECTOR (for Port Injection) › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072204 6AR-FSE FUEL _0353735 FUEL INJECTOR(for Port Injection) A

6AR-FSE FUEL  FUEL INJECTOR(for Port Injection)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during port fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Departure Alert System (w/ Steering Control) (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
·

Replacement of port fuel injector assembly

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 22030 5.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 23801P 6.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23901 7.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A413964

Disconnect the fuel tube sub-assembly from the fuel delivery pipe.

Click hereEngine / Hybrid System>6AR-FSE (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 12262 8.DISCONNECT NO. 2 VENTILATION HOSE

Hide 82128A 9.DISCONNECT NO. 8 ENGINE WIRE

A420653

a.

Disconnect the 4 port fuel injector assembly connectors.


b.

Disengage the 3 clamps to disconnect the No. 8 engine wire from the fuel delivery pipe.


Hide 23814B 10.REMOVE FUEL DELIVERY PIPE

a.
A420654

Remove the 2 bolts and fuel delivery pipe with the port fuel injector assemblies.

NOTICE:

Be careful not to drop the port fuel injector assemblies when removing the fuel delivery pipe.



Hide 23891 11.REMOVE FUEL DELIVERY SPACER

a.
A337364

Remove the 2 fuel delivery spacers from the cylinder head sub-assembly.


Hide 23291 12.REMOVE INJECTOR VIBRATION INSULATOR

a.
A337365

Remove the 4 injector vibration insulators from the cylinder head sub-assembly.


Hide 23250F 13.REMOVE PORT FUEL INJECTOR ASSEMBLY

a.
A411917

Pull the 4 port fuel injector assemblies out of the fuel delivery pipe.


b.
A413967

Remove the O-ring from each port fuel injector assembly.


c.
A413968N01
2.01,0.698 2.781,0.896 0.771,0.198 10 false No. 1

Attach a tag or label with the corresponding cylinder number to each port fuel injector assembly so that they can be installed to their original locations.

NOTICE:

Cover the port fuel injector assemblies with plastic bags to prevent damage and contamination.