Home › Engine / Hybrid System › 6AR-FSE (ENGINE CONTROL) › SFI SYSTEM › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072203 6AR-FSE ENGINE CONTROL _0351507 SFI SYSTEM J

6AR-FSE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the engine switch is turned on (IG), the battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil of the EFI-MAIN NO. 1 relay, closing the contact and supplying power to terminals +B and +B2 of the ECM.

WIRING DIAGRAM

A409697E03
0.594,4.406 1.667,4.604 1.073,0.198 10 false Battery 0.396,3.073 1.469,3.271 1.073,0.198 10 false FL MAIN 2.115,2.125 3.188,2.323 1.073,0.198 10 false IG2-MAIN 1.927,3.375 3,3.573 1.073,0.198 10 false EFI-MAIN NO. 1 0.646,1.385 3.646,1.625 3,0.24 10 false Certification ECU (Smart Key ECU Assembly) 0.646,1.24 3.646,1.479 3,0.24 10 false K62 3.083,2.594 4.156,2.792 1.073,0.198 10 false IG2 NO. 1 2.813,3.896 3.938,4.104 1.125,0.208 10 false EFI-MAIN NO. 1 4.438,2.125 5.51,2.323 1.073,0.198 10 false ECU-IG2 NO. 1 6.458,5.188 6.938,5.448 0.479,0.26 10 false ECM 5.833,4.667 6.313,4.927 0.479,0.26 10 false C58 6.167,4.656 6.646,4.917 0.479,0.26 10 false E1 5.875,4.469 6.354,4.729 0.479,0.26 10 false 53 6.156,4.125 6.635,4.385 0.479,0.26 10 false MREL 5.833,4.229 6.313,4.49 0.479,0.26 10 false A78 5.885,4.042 6.365,4.302 0.479,0.26 10 false 46 5.917,1.802 6.396,2.063 0.479,0.26 10 false 6 6.167,1.885 6.646,2.146 0.479,0.26 10 false IGSW 5.833,1.99 6.313,2.25 0.479,0.26 10 false A78 5.833,2.854 6.313,3.115 0.479,0.26 10 false A78 5.833,3.24 6.313,3.5 0.479,0.26 10 false A78 5.917,2.667 6.396,2.927 0.479,0.26 10 false 2 5.917,3.052 6.396,3.313 0.479,0.26 10 false 3 6.177,2.854 6.656,3.115 0.479,0.26 10 false +B 6.177,3.24 6.656,3.5 0.479,0.26 10 false +B2 2.052,0.854 3.125,1.052 1.073,0.198 10 false IG1D 2.448,0.74 3.521,0.938 1.073,0.198 10 false 17 2.99,1.875 4.063,2.073 1.073,0.198 10 false 5 3,2.219 4.073,2.417 1.073,0.198 10 false 2 2.99,3.563 4.063,3.76 1.073,0.198 10 false 2 3.698,1.865 4.771,2.063 1.073,0.198 10 false 3 3.677,2.219 4.75,2.417 1.073,0.198 10 false 1 2.979,3.125 4.052,3.323 1.073,0.198 10 false 3 3.677,3.125 4.75,3.323 1.073,0.198 10 false 5 3.677,3.552 4.75,3.75 1.073,0.198 10 false 1 4.635,3.5 5.708,3.698 1.073,0.198 10 false 1 4.958,3.5 6.031,3.698 1.073,0.198 10 false 2 4.573,3.76 5.698,3.969 1.125,0.208 10 false EFI NO. 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C58-53 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (IGSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (IGSW TERMINAL VOLTAGE)
A413387C04
0.167,0.917 0.583,1.167 0.417,0.25 1.479,1.708 1.99,0.885 true 0.177,0.208 0.49,0.406 0.313,0.198 10 false *a 0.24,0.948 0.698,1.146 0.458,0.198 10 false A78 1.26,1.74 1.875,1.938 0.615,0.198 10 false IGSW
*a Front view of wire harness connector
(to ECM)


a.

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A78-6 (IGSW) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT EFI-MAIN NO. 1 RELAY

NG

7.INSPECT IG2 NO. 1 RELAY
3.INSPECT EFI-MAIN NO. 1 RELAY

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - BODY GROUND)

NG

REPLACE EFI-MAIN NO. 1 RELAY

4.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI-MAIN NO. 1 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)
a.

Remove the EFI-MAIN NO. 1, EFI-MAIN NO. 2 and EFI-MAIN NO. 3 relays from the engine room relay block and junction block assembly.

HINT:

Remove the EFI-MAIN NO. 2 and EFI-MAIN NO. 3 relays connected between the checked terminals as the coil inside the relay influences the measurement value.



b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (EFI-MAIN NO. 1 relay) - A78-46 (MREL) Always Below 1 Ω
5 (EFI-MAIN NO. 1 relay) - A78-2 (+B) Always Below 1 Ω
5 (EFI-MAIN NO. 1 relay) - A78-3 (+B2) Always Below 1 Ω
2 (EFI-MAIN NO. 1 relay) or A78-46 (MREL) - Body ground and other terminals Always 10 kΩ or higher
5 (EFI-MAIN NO. 1 relay), A78-2 (+B) or A78-3 (+B2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 1 RELAY)
A402439C03
0.135,0.146 0.448,0.406 0.313,0.26 10 false *1 2.26,0.99 2.573,1.25 0.313,0.26 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 EFI-MAIN NO. 1 Relay


a.

Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (EFI-MAIN NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN NO. 1 RELAY)

7.INSPECT IG2 NO. 1 RELAY

Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - ECM)

NG

REPLACE IG2 NO. 1 RELAY

8.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - ECM)
a.

Remove the IG2 NO. 1 relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG2 NO. 1 relay) - A78-6 (IGSW) Always Below 1 Ω
3 (IG2 NO. 1 relay) or A78-6 (IGSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IG2 NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IG2 NO. 1 RELAY)
A402425C03
0.177,0.177 0.49,0.375 0.313,0.198 10 false *1 2.271,1 2.583,1.198 0.313,0.198 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 IG2 NO. 1 Relay


a.

Remove the IG2 NO. 1 relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (IG2 NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IG2 NO. 1 RELAY)

10.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - BODY GROUND)
a.

Remove the IG2 NO. 1 relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IG2 NO. 1 relay) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK A
NG B



A

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG2 NO. 1 RELAY)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG2 NO. 1 RELAY)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Remove the IG2 NO. 1 relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K62-17 (IG1D) - 1 (IG2 NO. 1 relay) Always Below 1 Ω
K62-17 (IG1D) or 1 (IG2 NO. 1 relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR