Home › Engine / Hybrid System › 6AR-FSE (ENGINE CONTROL) › THROTTLE BODY › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072203 6AR-FSE ENGINE CONTROL _0351512 THROTTLE BODY A

6AR-FSE ENGINE CONTROL  THROTTLE BODY  INSTALLATION  


PROCEDURE

Hide 22271 1.INSTALL THROTTLE BODY GASKET

a.
A413326C01
1.688,0.667 1.958,0.406 1.958,0.406 2.177,0.406 true 2.198,0.323 2.51,0.521 0.313,0.198 10 true *a
*a Protrusion


Install a new throttle body gasket to the intake manifold with the protrusion of the throttle body gasket oriented as shown in the illustration.


Hide 22030 2.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Install the throttle body with motor assembly to the intake manifold with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

If the throttle body with motor assembly has been struck or dropped, replace it.



b.

Connect the throttle body with motor assembly connector.


c.
A413324C01
0.885,2.667 1.24,2.667 true 1.135,1.052 1.281,1.052 1.281,1.052 1.802,1.354 true 0.948,2.458 1.115,2.458 1.115,2.458 1.313,2.615 true 2.396,2.833 2.646,2.833 true 2.281,1.25 2.708,1.25 true 1.229,1.885 1.229,1.635 true 1.042,2.24 1.354,2.396 0.313,0.156 10 false *a 1.583,2.792 1.896,2.948 0.313,0.156 10 false *b 3.063,2.698 3.375,2.854 0.313,0.156 10 false *c 0.729,2.583 1.042,2.74 0.313,0.156 10 false *d 0.948,0.969 1.135,1.167 0.188,0.198 10 true *e 1.448,2.281 1.76,2.438 0.313,0.156 10 false *f 0.792,2.354 0.979,2.552 0.188,0.198 10 false *e 2.25,2.74 2.563,2.896 0.313,0.156 10 false *d 2.729,3.042 3.042,3.198 0.313,0.156 10 false *b 2.729,1.156 2.917,1.354 0.188,0.198 10 true *1 1.167,1.896 1.354,2.094 0.188,0.198 10 true *2
*1 No. 2 Water By-pass Hose
*2 No. 3 Water By-pass Hose
*a Top
*b Left of Vehicle
*c Rear of Vehicle
*d Paint Mark
*e Protrusion
*f Protrusion Location


Connect the No. 3 water by-pass hose to the throttle body with motor assembly and slide the clip to secure it.

NOTICE:
·

Align the paint mark of the No. 3 water by-pass hose with the protrusion of the throttle body with motor assembly.

·

Make sure to position the clip as shown in the illustration.




d.

Connect the No. 2 water by-pass hose to the throttle body with motor assembly and slide the clip to secure it.

NOTICE:

Make sure to position the clip as shown in the illustration.



Hide 17705 3.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

a.
A413322C01
2.198,4.313 2.417,4.313 2.417,4.313 2.979,3.938 true 2.063,3.969 2.063,3.552 2.063,3.552 2.292,3.552 true 0.167,0.719 0.479,0.875 0.313,0.156 10 false *a 2.021,3.969 2.333,4.125 0.313,0.156 10 false *b 2.042,4.229 2.354,4.385 0.313,0.156 10 false *c
*a 12 to 18 mm (0.472 to 0.709 in.)
*b Cutout
*c Protrusion


Install the air cleaner cap with air cleaner hose to the throttle body with motor assembly as shown in the illustration.

NOTICE:

Align the cutout of the air cleaner hose with the protrusion of the throttle body with motor assembly.



b.

Tighten the hose clamp in the position shown in the illustration.


c.

Engage the 2 guides to connect the air cleaner cap with air cleaner hose to the air cleaner case sub-assembly.


d.

Engage the 2 air cleaner cap clamps.


e.

Engage the clamp to connect the No. 1 fuel hose sub-assembly to the fuel hose bracket.


f.

Engage the clamp to connect the heater hose to the air cleaner hose assembly.


g.

Engage the 2 clamps to connect the No. 2 fuel vapor feed hose assembly to the air cleaner hose assembly.


h.

Engage the clamp to connect the union to check valve hose to the air cleaner hose assembly.


i.

Engage the 2 wire harness clamps.


j.

Connect the mass air flow meter sub-assembly connector.


k.

Engage the clamp to connect the ventilation hose to the engine wire.


l.
A413316C01
1.125,2.792 1.344,3.177 1.344,3.177 1.521,3.177 true 1.021,1.927 1.333,2.083 0.313,0.156 10 false *a 1.542,3.115 1.854,3.271 0.313,0.156 10 false *b 0.719,2.125 1.031,2.281 0.313,0.156 10 false *c 1.292,2.125 1.604,2.281 0.313,0.156 10 false *c
*a Top
*b Paint Mark
*c 45°(Claw of Clip Location)


Connect the ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.

NOTICE:

Make sure to position the clip as shown in the illustration.



Hide 5.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 6.ADD ENGINE COOLANT

Hide 12601B 8.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 9.PERFORM INITIALIZATION

NOTICE:
·

Be sure to perform this procedure after removing and reinstalling the throttle body with motor assembly or any throttle body with motor assembly components.

·

Perform the following procedure after replacing the throttle body with motor assembly or any throttle body with motor assembly components. The following procedure should also be performed if the throttle body with motor assembly is cleaned.



a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

f.

Start the engine and check that the MIL is not illuminated. After the engine is warmed up, check that the idle speed is within the specified range with the A/C switch off.

Standard Idle Speed:

600 to 700 rpm


NOTICE:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in P or N.




g.

Enter the following menus: Powertrain / Engine / Data List / Throttle Position Sensor No.1 Voltage %.

Powertrain > Engine > Data List
Tester Display
Throttle Position Sensor No.1 Voltage %
50003 372 216

h.

According to the display on the GTS, read the Data List while fully depressing the accelerator pedal and check that the value is 60% or higher.


i.

Perform a road test and confirm that there are no abnormalities.