Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2018.04–2021.02
RM33A0E _58 Vehicle Interior _065387 HEATING / AIR CONDITIONING _0327417 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Air Conditioning Compressor Magnetic Clutch Circuit  


DESCRIPTION

When the engine is running, If refrigerant pressure does not decrease when the A/C switch is turned off, the following factors may be the cause.

Symptom Factor
·

Cooler compressor assembly does not stop operating

·

Refrigerant pressure does not decrease when A/C switch is turned off


·

Short to +B in air conditioning amplifier assembly circuit malfunction

·

MG CLT relay malfunction

·

Magnet clutch assembly malfunction

·

Harness or connector



WIRING DIAGRAM

E383799E01
0.25,0.698 1.677,0.917 1.427,0.219 10 false from IG1-NO. 1 Relay 0.802,1.24 1.635,1.458 0.833,0.219 10 false from Battery 1.948,0.854 2.979,1.063 1.031,0.208 10 false ECU-IG1 NO. 3 2.073,1.385 2.823,1.583 0.75,0.198 10 false A/C COMP 3.115,1.521 3.76,1.729 0.646,0.208 10 false MG CLT 6.021,0.615 6.438,0.823 0.417,0.208 10 false MGC 5.844,0.615 6.021,0.813 0.177,0.198 10 false 9 5.594,3.531 5.875,3.708 0.281,0.177 10 false K55 5.594,3.708 7.156,4.083 1.563,0.375 10 false Air Conditioning Amplifier Assembly 2.979,0.625 3.167,0.823 0.188,0.198 10 false 1 3.646,0.625 3.833,0.823 0.188,0.198 10 false 2 2.99,1.167 3.177,1.365 0.188,0.198 10 false 3 3.646,1.167 3.833,1.365 0.188,0.198 10 false 5 3.99,2.708 4.365,2.917 0.375,0.208 10 false MG+ 4.396,2.708 4.583,2.906 0.188,0.198 10 false 3 2.625,3.563 2.906,3.74 0.281,0.177 10 false C63 2.625,3.729 4.24,3.948 1.615,0.219 10 false Magnet Clutch Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.INSPECT MG CLT RELAY

Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MG CLT RELAY - POWER SOURCE)

NG

REPLACE MG CLT RELAY

2.CHECK HARNESS AND CONNECTOR (MG CLT RELAY - POWER SOURCE)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (MG CLT relay) - Body ground Always 11 to 14 V
1 (MG CLT relay) - Body ground Ignition switch off Below 1 V
1 (MG CLT relay) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MG CLT RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MG CLT RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the K55 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (MG CLT relay) - K55-9 (MGC) Always Below 1 Ω
2 (MG CLT relay) or K55-9 (MGC) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MG CLT RELAY - MAGNET CLUTCH ASSEMBLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MG CLT RELAY - MAGNET CLUTCH ASSEMBLY AND BODY GROUND)
a.

Disconnect the C63 magnet clutch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (MG CLT relay) - C63-3 (MG+) Always Below 1 Ω
5 (MG CLT relay) or C63-3 (MG+) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (MAGNET CLUTCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MAGNET CLUTCH ASSEMBLY - BODY GROUND)
a.

Connect the C63 magnet clutch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C63-3 (MG+) - Body ground Engine running
(A/C switch: Off)
Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR