The air conditioning amplifier assembly sends operation signals to the PTC HTR relays when quick heater assembly operation conditions are met. Based on the signals from the air conditioning amplifier assembly, the PTC HTR relays turn on, and power is supplied to the quick heater assembly installed in the air conditioning radiator assembly.
| Symptom | Factor |
|---|---|
| Heating performance is poor when it is cold. | ·
Quick heater assembly malfunction ·
Air conditioning amplifier assembly malfunction ·
PTC HTR relay malfunction ·
Harness or connector |
Inspect the fuses for circuits related to this system before performing the following procedure.
Inspect the PTC HTR relays.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (PTC HTR NO. 1 relay) - Body ground | Always | 11 to 14 V |
| 2 (PTC HTR NO. 1 relay) - Body ground | Ignition switch off | Below 1 V |
| 2 (PTC HTR NO. 1 relay) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (PTC HTR NO. 2 relay) - Body ground | Always | 11 to 14 V |
| 2 (PTC HTR NO. 2 relay) - Body ground | Ignition switch off | Below 1 V |
| 2 (PTC HTR NO. 2 relay) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K54 and K55 air conditioning amplifier assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (PTC HTR NO. 1 relay) - K54-18 (PTC1) | Always | Below 1 Ω |
| 1 (PTC HTR NO. 1 relay) or K54-18 (PTC1) - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (PTC HTR NO. 2 relay) - K55-10 (PTC2) | Always | Below 1 Ω |
| 1 (PTC HTR NO. 2 relay) or K55-10 (PTC2) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the L1 and L2 quick heater assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (PTC HTR NO. 1 relay) - L1-2 (B) | Always | Below 1 Ω |
| 5 (PTC HTR NO. 1 relay) - L2-1 (B) | Always | Below 1 Ω |
| 5 (PTC HTR NO. 1 relay) or L1-2 (B) - Other terminals and body ground | Always | 10 kΩ or higher |
| 5 (PTC HTR NO. 1 relay) or L2-1 (B) - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (PTC HTR NO. 2 relay) - L2-3 (B) | Always | Below 1 Ω |
| 5 (PTC HTR NO. 2 relay) or L2-3 (B) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the quick heater assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>PTC HEATER ASSEMBLY>REMOVAL
Inspect the quick heater assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>PTC HEATER ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG