Home › Engine / Hybrid System › 6AR-FSE (FUEL) › FUEL PUMP (for High Pressure) › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072204 6AR-FSE FUEL _0353739 FUEL PUMP(for High Pressure) A

6AR-FSE FUEL  FUEL PUMP(for High Pressure)  INSTALLATION  


PROCEDURE

Hide 23021 1.TEMPORARILY INSTALL FUEL PUMP WITH SEAL SUB-ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the fuel pump with seal sub-assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A326508C03
0.844,0.958 0.521,1.052 0.521,1.052 0.354,1.052 false 2.552,0.896 3.052,0.896 false 2.906,1.417 3.083,1.417 false 0.344,1.667 0.594,1.667 false 0.917,0.427 1.229,0.583 0.313,0.156 10 false *1 0.167,0.969 0.479,1.125 0.313,0.156 10 false *2 0.167,1.583 0.479,1.74 0.313,0.156 10 false *3 0.854,0.135 1.167,0.292 0.313,0.156 10 false *a 2.354,0.125 2.667,0.281 0.313,0.156 10 false *b 2.469,0.427 2.781,0.583 0.313,0.156 10 false *1 3.083,0.813 3.396,0.969 0.313,0.156 10 false *2 3.125,1.344 3.385,1.5 0.26,0.156 10 false *3
*1 Fuel Pump Lifter Guide
*2 Fuel Pump Lifter Assembly
*3 Camshaft
*a Correct
*b Incorrect


Turn the crankshaft pulley until the flat of the camshaft faces the fuel pump with seal sub-assembly installation hole of the cylinder head cover sub-assembly.

HINT:

This prevent the camshaft nose from pushing up the fuel pump lifter assembly when installing the fuel pump with seal sub-assembly.



b.
A304572C03
0.927,1.354 1.115,1.354 1.115,1.354 1.521,1.125 false 2.021,0.417 2.542,0.417 false 2.229,1.792 2.75,1.792 false 1.927,2.833 2.448,2.833 false 2.458,3.667 2.885,3.667 false 2.615,0.344 2.927,0.5 0.313,0.156 10 false *1 0.74,1.292 1.052,1.448 0.313,0.156 10 false *2 2.802,1.729 3.115,1.885 0.313,0.156 10 false *3 2.5,2.771 2.813,2.927 0.313,0.156 10 false *4 2.948,3.604 3.26,3.76 0.313,0.156 10 false *5
*1 Fuel Pump with Seal Sub-assembly
*2 O-ring
*3 Fuel Pump Insulator
*4 Fuel Pump Lifter Assembly
*5 Fuel Pump Lifter Guide
V100145

Engine Oil Application Area


Apply engine oil to a new O-ring and install it to the fuel pump with seal sub-assembly.

NOTICE:

Do not damage the O-ring.



c.

Apply engine oil to the inside of the fuel pump lifter guide and the outside of the fuel pump lifter assembly.


d.

Install the fuel pump lifter assembly to the fuel pump lifter guide.


e.

Install the fuel pump insulator to the fuel pump lifter guide.


f.

Install the fuel pump with seal sub-assembly to the fuel pump lifter guide.


g.
A338470C01
0.49,0.688 0.656,0.688 0.656,0.688 0.823,0.885 true 0.49,2.458 0.49,1.646 false 1.083,2.021 1.083,1.552 true 2.271,0.635 2.604,0.292 2.604,0.292 2.74,0.292 true 2.188,0.979 2.771,0.979 true 0.74,0.396 0.885,0.396 0.885,0.396 1.583,0.896 true 1.125,0.979 1.698,2.354 1.698,2.354 2.177,1.208 true 1.583,4.208 0.75,3.563 0.75,3.563 1.99,3.406 true 2.156,4.281 2.719,4.281 true 0.417,2.5 0.729,2.656 0.313,0.156 10 false *1 1.021,2.063 1.333,2.219 0.313,0.156 10 false *2 0.323,0.615 0.635,0.771 0.313,0.156 10 false *3 2.823,0.906 3.135,1.063 0.313,0.156 10 false *4 0.563,0.302 0.875,0.458 0.313,0.156 10 false *a 2.771,4.198 3.083,4.354 0.313,0.156 10 false *b 1.615,2.385 1.927,2.542 0.313,0.156 10 false *c 0.563,3.49 0.875,3.646 0.313,0.156 10 false *d 2.802,0.208 3.115,0.365 0.313,0.156 10 false *2
*1 Cylinder Head Cover Sub-assembly
*2 O-ring
*3 Fuel Pump Spacer Gasket
*4 No. 4 Camshaft Bearing Cap
*a Pump Drive Cam (Engine Oil Application Area)
*b Pump Lifter (Engine Oil Application Area)
*c Knock Pin
*d Pin Hole


Apply 30 cc (1.8 cu. in.) of engine oil to the pump drive cam.


h.

Apply engine oil to the fuel pump lifter assembly.


i.

Apply engine oil to 2 new O-rings and install them to the No. 4 camshaft bearing cap.


j.

Install a new fuel pump spacer gasket to the cylinder head cover sub-assembly.


k.

Set the fuel pump with seal sub-assembly on the cylinder head cover sub-assembly.


l.

Temporarily install the fuel pump with seal sub-assembly with the 2 bolts, leaving some allowance for left and right movement.


Hide 23801P 2.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

NOTICE:

Do not damage the seals of the union nuts of the No. 1 fuel pipe sub-assembly.


a.

Connect the No. 1 fuel pipe sub-assembly to the fuel delivery pipe sub-assembly and tighten the union nut by hand.


b.

Connect the No. 1 fuel pipe sub-assembly to the fuel pump with seal sub-assembly and tighten the union nut by hand.


Hide 23021 3.INSTALL FUEL PUMP WITH SEAL SUB-ASSEMBLY

a.
A339043N01
0.938,0.594 1.083,0.76 0.146,0.167 10 true 1 1.813,0.302 1.958,0.469 0.146,0.167 10 true 2

Tighten the 2 bolts in the order shown in the illustration.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


b.

Connect the fuel pump with seal sub-assembly connector.


Hide 23801P 4.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A412636C01
2.719,0.74 2.719,0.542 2.719,0.542 2.854,0.542 false 2.917,0.469 3.229,0.625 0.313,0.156 10 false *a 1.573,0.406 1.885,0.563 0.313,0.156 10 false *b
*a 17 mm Union Nut Wrench
*b Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the union nuts on the fuel pump with seal sub-assembly side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




b.

Using a 17 mm union nut wrench, tighten the union nuts on the fuel delivery pipe sub-assembly side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




Hide 23811B 5.INSTALL NO. 1 FUEL PIPE

a.
A412634C01
1.969,1.583 2.271,1.802 2.271,1.802 2.406,1.802 true 2.448,1.729 2.635,1.896 0.188,0.167 10 true *a
*a 17 mm Deep Socket Wrench


Using a 17 mm deep socket wrench, install the No. 1 fuel pipe and a new gasket to the fuel pump with seal sub-assembly.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 6.CONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

a.

Connect the No. 2 fuel tube sub-assembly to the No. 1 fuel pipe.

Click hereEngine / Hybrid System>6AR-FSE (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 7.INSTALL FUEL PUMP PROTECTOR

a.

Install the fuel pump protector to the cylinder head cover sub-assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 22030 8.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 9.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 11.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the fuel pump with seal sub-assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION