Home › Engine / Hybrid System › 2AR-FE (FUEL) › FUEL INJECTOR › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _065325 2AR-FE FUEL _0328388 FUEL INJECTOR A

2AR-FE FUEL  FUEL INJECTOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Replacement of fuel injector assembly Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 12601B 4.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 17705 5.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 23901 6.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A401631C01
0,0 0,0 false
V100135

Open
V100136

Pull


Open the cover of the No. 1 fuel pipe clamp and remove the No. 1 fuel pipe clamp from the fuel tube connector.


b.
A405889

Disconnect the fuel tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>2AR-FE (FUEL)>FUEL SYSTEM>PRECAUTION


c.

Disengage the clamp to disconnect the fuel tube sub-assembly from the fuel hose clamp.


Hide 17650 7.REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)

Hide 82121 8.DISCONNECT ENGINE WIRE

a.
A405890C01
0,0 0,0 false
V100136

Bolt


Disconnect the 4 fuel injector assembly connectors, throttle body with motor assembly connector, purge valve (purge VSV) connector and sensor wire connector.


b.

Remove the 2 bolts and separate the 2 wire harness brackets from the intake manifold.


c.

Disengage the clamp to disconnect the engine wire.


Hide 23814B 9.REMOVE FUEL DELIVERY PIPE

a.
A405891

Remove the 2 bolts and fuel delivery pipe with the 4 fuel injector assemblies.

NOTICE:

Be careful not to drop the fuel injector assemblies when removing the fuel delivery pipe.



Hide 23891 10.REMOVE FUEL DELIVERY SPACER

a.
A405892

Remove the 2 No. 1 fuel delivery spacers from the cylinder head sub-assembly.


Hide 23291 11.REMOVE INJECTOR VIBRATION INSULATOR

a.
A405893

Remove the 4 injector vibration insulators from the cylinder head sub-assembly.


Hide 23250 12.REMOVE FUEL INJECTOR ASSEMBLY

a.
A341560

Pull the 4 fuel injector assemblies out of the fuel delivery pipe.


b.
A341561C01
3.083,1.604 3.083,1.313 false 3.01,1.635 3.323,1.792 0.313,0.156 10 false *1
*1 O-ring


Remove the O-ring from each fuel injector assembly.


c.
A405894

Attach a tag or label with the corresponding cylinder number to each fuel injector assembly so that they can be installed to their original locations.

NOTICE:

Cover the fuel injector assemblies with plastic bags to prevent damage and contamination.