Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › 2018.04–2020.02
RM33A0E _59 Vehicle Exterior _065392 DOOR / HATCH _0326916 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75978H 3.INSTALL REAR DOOR LOWER OUTSIDE STRIPE

Hide 75708 4.INSTALL REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY

Hide 67846A 5.INSTALL REAR DOOR FRONT OUTSIDE SEAL

a.
B471662

Engage the guide to install the rear door front outside seal.


Hide 75762A 6.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING

Hide 75792 7.INSTALL DOOR WINDOW FRAME MOULDING CLIP

a.
B469836C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the door window frame moulding clip.


Hide 75740 8.INSTALL REAR DOOR BELT MOULDING ASSEMBLY

Hide 67888F 9.INSTALL REAR DOOR NO. 2 WEATHERSTRIP

a.
B471660

Engage the 5 clips to install the rear door No. 2 weatherstrip.


Hide 67003C 10.INSTALL REAR DOOR PANEL CUSHION

a.
B471659

Engage the 4 claws to install 2 new rear door panel cushions.


Hide 65923E 11.INSTALL CURTAIN HOOK (w/ Rear Door Sunshade)

a.
B488902

Engage the 4 claws to install the 2 curtain hooks.


b.

Engage the 2 pins as shown in the illustration.


Hide 69204A 12.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.


b.
B471658C01
0.052,0.052 0.417,0.365 0.365,0.313 12 true *A 0.052,2.552 0.417,2.844 0.365,0.292 12 true *B
*A Outside
*B Inside


Engage the claw as shown in the illustration.


c.

Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242G 13.INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD

a.
B471656

Engage the 3 guides and claw to install the rear door rear outside handle pad.


Hide 69241G 14.INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD

a.
B471655

Engage the 3 claws to install the rear door front outside handle pad.


Hide 69227L 15.INSTALL REAR DOOR OUTSIDE HANDLE COVER

a.
B471654

Engage the claw.


b.

Using a T30 "TORX" socket wrench, install the rear door outside handle cover with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69240 16.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B471653C01
0,0 0,0 false
V113147

Install in this Direction


Insert the front end of the rear door outside handle assembly into the rear door outside handle frame sub-assembly.


b.

Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame sub-assembly, then slide the rear door outside handle assembly toward the front of the vehicle to install it.


c.
B471651C01
0,0 0,0 false
V113147

Engage in this Direction


Move the lever as shown in the illustration and engage the 2 claws to secure the rear door outside handle assembly.


Hide 69060A 17.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY

Hide 18.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door window regulator assembly.


b.

Temporarily install the temporary bolt to the rear door window regulator assembly.


c.
B471649C01
0.979,0.323 1.5,0.438 true 0.75,0.198 1,0.417 0.25,0.219 10 true *a 1.948,1.354 2.135,1.563 0.188,0.208 10 true 1 2.479,0.063 2.667,0.271 0.188,0.208 10 true 2 2.552,1.052 2.74,1.26 0.188,0.208 10 true 3 1.844,0.042 2.031,0.25 0.188,0.208 10 true 4
*a Temporary Bolt


Temporarily install the rear door window regulator assembly with the 3 bolts.


d.

Tighten the temporary bolt and 3 bolts to install the rear door window regulator assembly.

HINT:

Tighten the bolts in the order shown in the illustration.


Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the connector.


Hide 69975A 19.INSTALL REAR DOOR GLASS CHANNEL FILLER

a.

Apply soapy water to a new rear door glass channel filler.


b.
B471647C01
0.25,0.729 0.479,0.896 false 2.896,0.906 3.125,0.792 false 1.063,0.125 1.448,0.344 0.385,0.219 12 false *A 2.094,0.125 2.531,0.375 0.438,0.25 12 false *B 0.094,0.625 0.406,0.781 0.313,0.156 10 false *a 3.146,0.688 3.365,0.917 0.219,0.229 10 false *a 0.49,0.344 0.802,0.5 0.313,0.156 10 false A 2.833,0.333 3.146,0.49 0.313,0.156 10 false B
*A Front Side
*B Rear Side
*a Edge of curved surface


Install the rear door glass channel filler to the rear door glass sub-assembly at position shown in the illustration.

Standard Dimension
Area Measurement
A 5.0 mm (0.197 in.)
B 5.0 mm (0.197 in.)


Hide 69906B 20.INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY

a.

Apply soapy water to the channel filler side of the rear door glass channel sub-assembly.


b.
B471646C01
0.229,0.927 0.427,1.063 false 2.854,1.063 3.052,0.938 false 1.021,0.302 1.396,0.5 0.375,0.198 12 false *A 2.042,0.313 2.396,0.573 0.354,0.26 12 false *B 0.063,0.813 0.375,0.969 0.313,0.156 10 false *a 3.063,0.833 3.375,0.99 0.313,0.156 10 false *a 0.438,0.51 0.75,0.667 0.313,0.156 10 false A 2.792,0.5 3.104,0.656 0.313,0.156 10 false B
*A Front Side
*B Rear Side
*a Edge of curved surface


Using a plastic hammer, install the rear door glass channel sub-assembly to the position shown in the illustration.

Standard Dimension
Area Measurement
A 5.0 mm (0.197 in.)
B 5.0 mm (0.197 in.)

NOTICE:

To prevent damaging the rear door glass sub-assembly, be careful not to strike the rear door glass channel sub-assembly with too much force.



Hide 68104 21.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

a.
B471644C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Insert the rear door glass sub-assembly into the rear door panel as indicated by the arrows, in the order shown in the illustration.

NOTICE:

Do not damage the rear door glass sub-assembly.



b.
B471527

Slide the rear door glass sub-assembly to install it as shown in the illustration.


Hide 68124B 22.INSTALL REAR DOOR QUARTER WINDOW GLASS

a.

Install the rear door quarter window glass to the rear door quarter window weatherstrip.


b.
B471524C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear door quarter window glass with rear door quarter window weatherstrip as shown in the illustration.


Hide 67408F 23.INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY

a.
B471523C02
0,0 0,0 false
V100135

Screw
V100136

Bolt


Install the rear door rear lower window frame sub-assembly with the screw and 2 bolts.

Torque:
Screw : 3.1 N*m (32 kgf*cm, 27 in.*lbf)
Bolt : 8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 67872 24.INSTALL REAR DOOR WEATHERSTRIP

a.

Clean the rear door panel.


b.

Remove the release paper from a new rear door weatherstrip.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.
B471522C01
0.563,0.979 1.01,0.865 true 1.031,0.75 1.344,0.948 0.313,0.198 10 true *a
*a Double-sided Tape


Engage the 23 clips and install the rear door weatherstrip.


Hide 68640A 25.INSTALL REAR DOOR CHECK ASSEMBLY

a.

Clean the bolt hole in the vehicle body.


b.

Clean the threads of the bolt.


c.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
B471519C02
0,0 0,0 false
V100135

Nut
V100136

Bolt


Install the rear door check assembly with the 2 nuts and bolt.

Torque:
Bolt : 29 N*m (296 kgf*cm, 21 ft.*lbf)
Nut : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 68152C 26.INSTALL REAR DOOR GLASS RUN

a.
B471518

Install the rear door glass run.


Hide 67858B 27.INSTALL REAR DOOR PANEL PROTECTOR

a.
B436647

Install the rear door panel protector.


b.
B477385

Engage the clip.


Hide 67848A 28.INSTALL REAR DOOR NO. 1 VENT SEAL

a.
B471512

Install the rear door No. 1 vent seal.


Hide 67842E 29.INSTALL REAR DOOR SERVICE HOLE COVER

a.
B471511

Engage the 8 clips to install the rear door service hole cover.


b.
B471510

Engage the 2 clamps.


c.

Connect the connector.


Hide 67674A 30.INSTALL REAR DOOR FRAME GARNISH

a.
B471509

Engage the 2 claws to install the rear door frame garnish.


Hide 86160B 31.INSTALL REAR SPEAKER ASSEMBLY

Hide 69206C 32.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B471508

Engage the 3 claws to install the rear door inside handle sub-assembly.


Hide 67844A 33.INSTALL REAR DOOR NO. 2 SERVICE HOLE COVER

a.
B471507C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear door No. 2 service hole cover to the rear door inner glass weatherstrip.


Hide 65907E 34.INSTALL REAR CURTAIN SUB-ASSEMBLY (w/ Rear Door Sunshade)

a.
B488903

Engage the 3 guides.


b.

Install the rear curtain sub-assembly with the 9 screws.


Hide 68174A 35.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP

a.
B471725C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear door inner glass weatherstrip with rear door No. 2 service hole cover as shown in the illustration.


b.
B477386

Engage the clip.


Hide 67604 36.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B471515

Install the No. 1 door scuff plate clamp as shown in the illustration.


b.
B471502C01
2.188,1.063 2.656,0.781 true 2.073,1.438 2.396,1.771 true 2.667,0.677 2.906,0.885 0.24,0.208 10 true *1 2.406,1.698 2.646,1.906 0.24,0.208 10 true *2
*1 Rear Door Inside Locking Cable Assembly
*2 Rear Door Lock Remote Control Cable Assembly
V113147

Install in this Direction


Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door inside handle sub-assembly as shown in the illustration.


c.
B570756

Engage the 5 claws and guide.


d.

Engage the 8 clips to install the rear door trim board sub-assembly.


e.
B471498

Install the 3 screws.


Hide 74260 37.INSTALL REAR ARMREST ASSEMBLY

a.
B471496C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide as shown in the illustration.


b.
B471494C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 3 clips, 8 claws and 2 guides to install the rear armrest assembly as shown in the illustration.


Hide 38.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

a.

Connect the connector.


b.
B471492C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 clips 5 claws and 6 guides to install the rear power window regulator switch assembly with rear door upper armrest base panel as shown in the illustration.


Hide 74038B 39.INSTALL REAR DOOR ARMREST COVER SUB-ASSEMBLY

a.
B471490

Engage the 3 claws to install the rear door armrest cover sub-assembly.


Hide 40.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 41. INITIALIZE POWER WINDOW CONTROL SYSTEM