Home › Drivetrain › U760E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE ASSEMBLY › 2018.08–2021.02
RM33A0E _52 Drivetrain _065350 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0326605 AUTOMATIC TRANSAXLE ASSEMBLY A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.


PROCEDURE

Hide 32000 1.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C378415C01
2.042,0.146 2.99,0.146 true 0.521,0.354 0.667,0.354 0.667,0.354 0.813,0.833 true 0.542,1.813 0.688,1.813 0.688,1.813 0.802,1.406 true 3.042,0.021 3.344,0.281 0.302,0.26 10 false *a 0.344,0.271 0.573,0.49 0.229,0.219 10 true *b 0.354,1.688 0.583,1.906 0.229,0.219 10 true *b
*a Matchmark
*b Key


Set the key at the top of the front oil pump drive gear and put a matchmark on the transaxle housing.


b.
C378416C01
1.365,1.979 1.51,1.979 1.51,1.979 1.688,1.563 false 1.427,0.26 1.552,0.26 1.552,0.26 1.729,0.677 false 1.208,0.156 1.51,0.417 0.302,0.26 10 false *a 1.177,1.875 1.458,2.063 0.281,0.188 10 false *b
*a Groove
*b Matchmark
V100135

MP Grease


Apply MP grease to place a matchmark on the torque converter assembly so that the position of its groove is clearly indicated.


c.
C378417C01
1.292,0.74 0.563,0.313 0.563,0.313 1.281,0.417 true 2.469,1.313 1.906,1.844 1.906,1.844 2.469,1.021 true 1.792,1.875 2.146,2.083 0.354,0.208 10 false *1 0.354,0.188 0.698,0.427 0.344,0.24 10 false *a
*1 Front Oil Pump Oil Seal
*a Matchmark


Align the matchmark on the housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




d.
C378418C01
2.49,1.313 1.927,1.896 1.927,1.896 2.469,1.01 true 0.854,2.021 1.01,2.021 1.01,2.021 1.281,1.615 true 0.865,0.156 1.021,0.156 1.021,0.156 1.271,0.417 true 1.771,1.938 2.094,2.135 0.323,0.198 10 false *1 0.667,1.917 1.01,2.146 0.344,0.229 10 false *a 0.667,0.063 1.01,0.292 0.344,0.229 10 false *a
*1 Front Oil Pump Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




e.
C378419C01
2.479,1.323 1.896,1.896 1.896,1.896 2.469,1.031 true 1.281,0.75 0.656,0.26 0.656,0.26 1.292,0.406 true 1.708,1.917 2.052,2.146 0.344,0.229 10 false *1 0.438,0.146 0.771,0.5 0.333,0.354 10 false *a
*1 Front Oil Pump Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the housing and insert the groove of the torque converter assembly into the key of the oil pump drive gear.

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




f.

Clean the drive plate and torque converter assembly setting bolt holes.


g.
C207515N09
2.448,0.271 2.698,0.563 0.25,0.292 10 false A

Using a vernier caliper and straightedge, measure the dimension (A) shown in the illustration and check the dimension (A).

Standard:

14 mm (0.5512 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the automatic transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

·

Do not include the thickness of the set block.




Hide 2.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the transaxle case sub-assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 35150 3.INSTALL TRANSMISSION CASE PLUG ASSEMBLY

a.

Coat a new O-ring with Toyota Genuine ATF WS and install it to the transmission case plug assembly.


b.

Install the transmission case plug assembly to the transaxle housing.


Hide 33823 4.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the transaxle case sub-assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 12303 5.INSTALL REAR ENGINE MOUNTING BRACKET SUB-ASSEMBLY

a.
C378411N01
2.344,0.583 2.5,0.781 0.156,0.198 10 true A 2.323,1.833 2.479,2.031 0.156,0.198 10 true B 2.458,1.146 2.615,1.344 0.156,0.198 10 true C 1.125,1.333 1.281,1.531 0.156,0.198 10 true C

Install the rear engine mounting bracket sub-assembly to the transaxle housing with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily tighten bolt (A) → Fully tighten bolt (B) → Fully tighten bolt (A) → Fully tighten bolt (C)



Hide 12371A 6.INSTALL REAR ENGINE MOUNTING INSULATOR

Hide 12372A 7.INSTALL ENGINE MOUNTING INSULATOR LH

a.
C378410N01
0.802,0.542 0.958,0.74 0.156,0.198 10 true A 2.427,0.708 2.583,0.906 0.156,0.198 10 true B 2.198,0.333 2.354,0.531 0.156,0.198 10 true C 0.802,1.01 0.958,1.208 0.156,0.198 10 true C

Install the engine mounting insulator LH to the transaxle case sub-assembly with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily tighten bolt (A) → Fully tighten bolt (B) → Fully tighten bolt (C) → Fully tighten bolt (A)



Hide 30500 8.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

a.
C378420C01
1.833,1.083 2.344,0.677 2.344,0.677 2.51,0.677 false 1.031,1.052 1.323,1.333 0.292,0.281 10 false *1 2.573,0.573 2.927,0.875 0.354,0.302 10 false *2
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch Spline Grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum Grease Amount:

Approximately 1 g (0.0353 oz)



b.
C378421C01
2.208,0.479 2.958,0.479 true 0.635,1.229 1.219,1.229 true 0.406,1.115 0.625,1.313 0.219,0.198 10 true *1 3.021,0.354 3.271,0.635 0.25,0.281 10 false *1
*1 Knock Pin


Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.


c.
C201719N03
0.948,1.781 1.104,1.979 0.156,0.198 10 true C 1.354,1.969 1.51,2.146 0.156,0.177 10 true C 2.823,1.823 3.031,2.01 0.208,0.188 10 true C 3.031,1.521 3.208,1.729 0.177,0.208 10 true C 3.115,1.135 3.24,1.313 0.125,0.177 10 true B 0.875,0.583 1,0.76 0.125,0.177 10 true B 1.063,0.083 1.208,0.302 0.146,0.219 10 true A 2.573,0.042 2.75,0.24 0.177,0.198 10 true A 2.979,0.479 3.188,0.688 0.208,0.208 10 true A

While keeping the engine assembly and automatic transaxle assembly horizontal, align the knock pins with the holes in the automatic transaxle assembly and install the automatic transaxle assembly with the 9 bolts shown in the illustration.

Bolt Bolt Length Torque
(A) 55 mm (2.17 in.) 64 N*m (653 kgf*cm, 47 ft.*lbf)
(B) 50 mm (1.97 in.) 46 N*m (469 kgf*cm, 34 ft.*lbf)
(C) 32 mm (1.26 in.) 44 N*m (449 kgf*cm, 32 ft.*lbf)
33 mm (1.30 in.) 43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:
·

Confirm that the knock pins are installed to the automatic transaxle assembly contact surface of the cylinder block sub-assembly before installing the automatic transaxle assembly.

·

Do not forcibly pry on the automatic transaxle assembly.

·

Check that the torque converter assembly rotates.




Hide 12311A 9.INSTALL FRONT ENGINE MOUNTING BRACKET

a.
C378409N01
0.979,0.417 1.125,0.615 0.146,0.198 10 true A 2.438,1.24 2.583,1.438 0.146,0.198 10 true B 0.99,1.76 1.135,1.958 0.146,0.198 10 true C

Install the front engine mounting bracket to the transaxle housing with the 3 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily tighten bolt (A) → Fully tighten bolt (B) → Fully tighten bolt (C) → Fully tighten bolt (A)



Hide 32941 12.INSTALL INLET NO. 1 OIL COOLER HOSE (w/o Air Cooled Oil Cooler)

a.
C378423C01
1.792,2.396 2.281,2.396 2.281,2.396 2.281,2.677 true 1.813,2.146 2.135,2.385 0.323,0.24 10 false *a 1.75,2.979 2.073,3.177 0.323,0.198 10 false *b 1.615,2.292 1.927,2.448 0.313,0.156 10 false *c 1.531,2.51 1.844,2.667 0.313,0.156 10 false *d 1.531,2.75 1.844,2.906 0.313,0.156 10 false *d
*a 0 to 3 mm (0 to 0.118 in.)
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c Paint Mark (Upper Side of Vehicle)
*d 30° (Paint Mark Location)


Install the inlet No. 1 oil cooler hose to the oil cooler tube union (inlet) and slide the clip to secure it.

NOTICE:
·

Make sure to slide the inlet No. 1 oil cooler hose until it contacts the hose stopper of the oil cooler tube union (inlet).

·

Make sure that the paint mark of the inlet No. 1 oil cooler hose is within the location shown in the illustration.




Hide 32942 13.INSTALL OUTLET NO. 1 OIL COOLER HOSE (w/o Air Cooled Oil Cooler)

a.
C378422C01
1.792,2.396 2.281,2.396 2.281,2.396 2.281,2.667 true 1.813,2.125 2.135,2.365 0.323,0.24 10 false *a 1.76,2.958 2.104,3.177 0.344,0.219 10 false *b 1.594,2.292 1.906,2.469 0.313,0.177 10 false *c 1.542,2.51 1.854,2.667 0.313,0.156 10 false *d 1.542,2.75 1.854,2.906 0.313,0.156 10 false *d
*a 0 to 3 mm (0 to 0.118 in.)
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c Paint Mark (Upper Side of Vehicle)
*d 30° (Paint Mark Location)


Install the outlet No. 1 oil cooler hose to the oil cooler tube union (outlet) and slide the clip to secure it.

NOTICE:
·

Make sure to slide the outlet No. 1 oil cooler hose until it contacts the hose stopper of the oil cooler tube union (outlet).

·

Make sure that the paint mark of the outlet No. 1 oil cooler hose is within the location shown in the illustration.




Hide 33493A 14.INSTALL TRANSMISSION OIL COOLER

Hide 32941 15.CONNECT INLET NO. 1 OIL COOLER HOSE (w/o Air Cooled Oil Cooler)

Hide 32942 16.CONNECT OUTLET NO. 1 OIL COOLER HOSE (w/o Air Cooled Oil Cooler)

Hide 82824D 17.INSTALL WIRING HARNESS CONNECTOR

a.

Install the wiring harness connector to the transaxle case sub-assembly.


b.
C238952N03
2.188,0.292 2.292,0.448 0.104,0.156 10 1 1.802,0.188 1.938,0.344 0.135,0.156 10 2

Temporarily install the 2 bolts.


c.

Tighten the 2 bolts in the order shown in the illustration.

Torque:
11.3 N*m (115 kgf*cm, 8 ft.*lbf)


Hide 18.CONNECT WIRE HARNESS

a.
C378407

Install the 2 bolts to connect the 2 earth wires to the automatic transaxle assembly.

Torque:
for TMC Made : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
except TMC Made : 20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Engage the 2 wire harness clamps to connect the wire harness.


c.

for LHD:

i.

Engage the 2 wire harness clamps to connect the wire harness.


ii.

Connect the wire harness to the rack and pinion power steering gear assembly with the 2 bolts.

C375738

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


iii.

Connect the rack and pinion power steering gear assembly connector.

NOTICE:

Make sure that the connector is fully inserted before rotating the lock lever to engage the lock.




d.

for RHD:

i.

Engage the wire harness clamp to connect the wire harness.


ii.

Connect the wire harness to the rack and pinion power steering gear assembly with the bolt.

C378435

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


iii.

Connect the rack and pinion power steering gear assembly connector.

NOTICE:

Make sure that the connector is fully inserted before rotating the lock lever to engage the lock.




e.

Connect the park/neutral position switch assembly connector.


f.
C378428

Connect the transmission wire connector and rotate the lever and engage the claw.

HINT:

Rotate the lever until the claw of the transmission wire connector makes a click sound.



Hide 28100 19.INSTALL STARTER ASSEMBLY

Hide 20.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

Hide 32101A 21.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Remove any remaining adhesive from the 6 drive plate and torque converter assembly setting bolts.


b.
P000601C22
1.979,1.177 2.177,0.229 2.177,0.229 2.302,0.229 false 2.323,0.135 2.521,0.323 0.198,0.188 10 false *a
*a Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the 6 drive plate and torque converter assembly setting bolts immediately after applying adhesive to prevent foreign matter from attaching to them.



c.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

NOTICE:

First install the black colored drive plate and torque converter assembly setting bolt, and then the remaining 5 silver colored drive plate and torque converter assembly setting bolts.



Hide 11361J 22.INSTALL FLYWHEEL HOUSING UNDER COVER

Hide 23.CHECK AUTOMATIC TRANSAXLE SYSTEM

NOTICE:

If automatic transaxle parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION