The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
12372A
1.INSTALL ENGINE MOUNTING INSULATOR LH
Perform this procedure only when replacement of the engine mounting insulator LH is necessary.
Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>INSTALLATION
12304
2.INSTALL ENGINE MOUNTING BRACKET SUB-ASSEMBLY LH
Perform this procedure only when replacement of the engine mounting bracket sub-assembly LH is necessary.
Temporarily tighten the bolt (A), and then fully tighten the 4 bolts in the order of (B), (C), (D) and (A).
Make sure that there is no gap between the engine mounting bracket sub-assembly LH and vehicle body before tightening the bolts.
12341
3.INSTALL ENGINE MOUNTING SPACER
Perform this procedure only when replacement of the engine mounting spacer is necessary.
Install the engine mounting spacer to the vehicle body with the 2 bolts.
Temporarily tighten the bolt (A), and then fully tighten the 2 bolts in the order of (B) and (A).
12305
4.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
Install the engine mounting insulator sub-assembly RH with the 2 bolts and nut.
Temporarily tighten the bolt (A), and then fully tighten the 2 bolts and nut in the order of (B), (A) and (C).
Engage the clamp.
Connect the No. 1 bond cable to the engine mounting insulator sub-assembly RH with the bolt.
Connect the bracket to the engine mounting insulator sub-assembly RH with the bolt.
| *a | Bolt |
| *b | Nut |
Install the radiator reserve tank assembly with the bolt and nut.
Temporarily tighten the bolt, nut and then fully tighten the bolt and nut in the order of bolt and nut.
Engage the clamp.
Engage the No. 6 water by-pass hose.
5.INSTALL ENGINE HANGERS
6.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND
Remove the engine assembly from the engine stand.
82121
7.INSTALL ENGINE WIRE
Install the engine wire to the engine assembly.
32101
8.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
30500
9.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY
32941
10.INSTALL INLET NO. 1 OIL COOLER HOSE (w/o Air Cooled Oil Cooler)
32942
11.INSTALL OUTLET NO. 1 OIL COOLER HOSE (w/o Air Cooled Oil Cooler)
33493A
12.INSTALL TRANSMISSION OIL COOLER
32941
13.CONNECT INLET NO. 1 OIL COOLER HOSE (w/o Air Cooled Oil Cooler)
32942
14.CONNECT OUTLET NO. 1 OIL COOLER HOSE (w/o Air Cooled Oil Cooler)
28100
15.INSTALL STARTER ASSEMBLY
12371A
16.INSTALL REAR ENGINE MOUNTING INSULATOR
Install the rear engine mounting insulator to the rear engine mounting bracket with the bolt.
12361A
17.INSTALL FRONT ENGINE MOUNTING INSULATOR
Install the front engine mounting insulator to the front engine mounting bracket with the bolt.
51100G
18.INSTALL FRONT FRAME ASSEMBLY
Install the front frame assembly with the 7 nuts.
19.CONNECT WIRE HARNESS
20.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
Perform inspection after repair after replacing the engine assembly.
Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Set the engine assembly with transaxle on an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly with transaxle.
Remove the 2 bolts, No. 1 engine hanger and No. 2 engine hanger.
Operate the engine lifter and install the engine assembly with transaxle to the vehicle.
Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.
|
Bolt |
|
Nut |
Install the front bumper extension sub-assembly RH and front bumper extension sub-assembly LH to the front frame assembly and vehicle body with the 8 bolts.
Install the front suspension member bracket sub-assembly RH and front suspension member bracket sub-assembly LH to the front frame assembly and vehicle body with the 4 bolts and 2 nuts.
Install the engine mounting insulator LH to the engine mounting bracket sub-assembly LH with the bolt and nut.
While holding the bolt in place, tighten the nut.
Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 2 bolts and nut.
Engage the clamp.
32101A
21.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
11361J
22.INSTALL FLYWHEEL HOUSING UNDER COVER
Install the flywheel housing under cover to the cylinder block sub-assembly.
23.INSTALL FRONT DRIVE SHAFT ASSEMBLY
17410
24.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
45220
25.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY
26.CONNECT WIRE HARNESS
Connect the wire harness to the vehicle body with the bolt.
Engage the claw to connect the wire harness to the engine room relay block and junction block assembly.
Connect the 4 connectors.
Install the nut.
Install the relay block cover.
Connect the wire harness with the 2 bolts.
27.CONNECT OIL COOLER HOSE (w/ Air Cooled Oil Cooler)
Connect the oil cooler hose and slide the clip to secure it.
Connect the 3 oil cooler hoses and slide the 3 clips to secure them.
28.CONNECT WATER HOSE
Engage the 4 clamps.
Connect the 4 water hoses and slide the 4 clips to secure them.
88704
29.CONNECT SUCTION HOSE SUB-ASSEMBLY
88711
30.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY
16572D
31.CONNECT NO. 2 RADIATOR HOSE
Connect the No. 2 radiator hose to the water inlet and slide the clip to secure it.
16571C
32.CONNECT NO. 1 RADIATOR HOSE
Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.
44774
33.CONNECT UNION TO CONNECTOR TUBE HOSE (for LHD)
Connect the union to connector tube hose and slide the clip to secure it.
44773F
34.CONNECT UNION TO CHECK VALVE HOSE (for RHD)
Connect the union to check valve hose and slide the clip to secure it.
23826
35.CONNECT NO. 1 FUEL VAPOR FEED HOSE
Connect the No. 1 fuel vapor feed hose to the No. 1 vacuum switching valve assembly and slide the clip to secure it.
23901
36.CONNECT FUEL TUBE SUB-ASSEMBLY
33820B
37.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.
Connect the transmission control cable assembly to the transmission control shaft lever with the nut.
Before installing the transmission control cable assembly, check that the park/neutral position switch assembly and shift lever are in N.
74404A
38.INSTALL BATTERY CLAMP SUB-ASSEMBLY
Install the battery clamp sub-assembly with the 3 bolts.
Engage the 5 clamps to the battery clamp sub-assembly.
39.INSTALL BATTERY
40.CONNECT WIRE HARNESS
Connect the wire harness to the positive (+) battery terminal with the nut.
89661
41.INSTALL ECM
42.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE
| *a | Air Cleaner Support |
Insert the 3 pins of the air cleaner assembly into the 3 air cleaner supports as shown in the illustration.
Insert the 3 pins of the air cleaner assembly into the 3 air cleaner supports at the same time.
Check that the pins are securely inserted into air cleaner supports.
Connect the air cleaner assembly with air cleaner hose to the throttle body with motor assembly and tighten the hose clamp.
Engage the 2 clamps.
Connect the ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.
Engage the 3 wire harness clamps.
Connect the mass air flow meter sub-assembly connector.
17750A
43.INSTALL INLET AIR CLEANER ASSEMBLY
Install the inlet air cleaner assembly with the 2 bolts in the order shown in the illustration.
12601B
44.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
Engage the 3 clips to install the No. 1 engine cover sub-assembly.
45.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
46.ADD ENGINE OIL
47.ADD ENGINE COOLANT
48.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
49. WARM UP ENGINE
50.INSPECT SHIFT LEVER POSITION
51.ADJUST SHIFT LEVER POSITION
52.INSPECT FOR ENGINE OIL LEAK
53.INSPECT FOR COOLANT LEAK
54.INSPECT FOR REFRIGERANT LEAK
55.INSPECT FOR FUEL LEAK
56.INSPECT FOR EXHAUST GAS LEAK
57.CHECK ENGINE OIL LEVEL
58.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR TANK
52618
59.INSTALL FRONT LOWER BUMPER ABSORBER
Engage the 2 claws to install the front lower bumper absorber.
Install the 4 bolts.
52119A
60.INSTALL FRONT BUMPER COVER
53737B
61.INSTALL FRONT FENDER APRON SEAL LH
Install the front fender apron seal LH with the 2 screws and clip.
53736
62.INSTALL FRONT FENDER APRON SEAL RH
Install the front fender apron seal RH with the 2 screws and clip.
51441
63.INSTALL NO. 1 ENGINE UNDER COVER
Install the No. 1 engine under cover with the bolt, 6 screws and 2 clips.
53852K
64.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH
Install the front wheel opening extension pad LH with the 3 screws.
53851M
65.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH
Install the front wheel opening extension pad RH with the 3 screws.
66.INSTALL FRONT WHEELS
67. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
68.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
69.PERFORM INITIALIZATION
70.INSPECT IGNITION TIMING
71.INSPECT ENGINE IDLE SPEED
72.INSPECT CO/HC
73.CHECK SPEED SENSOR SIGNAL