Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › FRONT CRANKSHAFT OIL SEAL › 2019.10–2020.02
RM33A0E _51 Engine / Hybrid System _065333 2GR-FKS ENGINE MECHANICAL _0327368 FRONT CRANKSHAFT OIL SEAL A

2GR-FKS ENGINE MECHANICAL  FRONT CRANKSHAFT OIL SEAL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front crankshaft oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
Gas leak from exhaust system is repaired Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly
1.

Reset Memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for Initialization
(Click here)
for Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Replacement of automatic transaxle fluid*2 ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
for Initialization
(Click here)
for Calibration
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic view monitor system (Click here)
for Initialization
(Click here)
for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

*2: for TMC Made

PROCEDURE

Hide 1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 16361A 2.REMOVE V-RIBBED BELT

Hide 13471 3.REMOVE CRANKSHAFT PULLEY

a.
A369429C01
0.635,1.594 1.281,0.438 1.281,0.438 2.094,0.823 true 1.635,2.375 1.281,0.448 true 2.781,2.406 3.094,2.563 0.313,0.156 10 false *a 1.135,0.24 1.594,0.438 0.458,0.198 10 false SST
*a Hold
V100135

Turn


Using SST to hold the crankshaft pulley, loosen the crankshaft pulley set bolt. Further loosen the crankshaft pulley set bolt until 2 or 3 threads remain screwed into the crankshaft.

SST
09213-70011  (09213-70020)
09330-00021  


b.
A369430C01
1.313,2.063 0.979,0.552 0.979,0.552 2.167,0.552 true 0.167,1.781 0.479,1.938 0.313,0.156 10 false *a 0.646,0.469 1.104,0.667 0.458,0.198 10 false SST
*a Hold
V100135

Turn


Using SST, remove the crankshaft pulley set bolt and crankshaft pulley.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05021)


Hide 11301C 4.REMOVE TIMING CHAIN CASE OIL SEAL

a.
A369431C01
1.854,1.24 2.417,0.896 true 2.458,0.792 2.771,0.948 0.313,0.156 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, pry out the timing chain case oil seal.

NOTICE:

After removal, check the crankshaft for damage. If it is damaged, smooth the surface with 400-grit sandpaper.