Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for LHD) › 2019.10–2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0319123 BRAKE ACTUATOR(for LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for LHD)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

The parking brake indicator light blinks (red) when the ignition switch is turned to ON after replacing the brake actuator assembly. Operate the electric parking brake switch assembly to turn off the parking brake indicator light.


PROCEDURE

Hide 44546A 1.INSTALL BRAKE ACTUATOR BOLT CUSHION

a.

Install the brake actuator bolt cushion to the brake actuator bracket assembly.


Hide 44521B 2.INSTALL NO. 2 BRAKE ACTUATOR CASE COLLAR

a.

Install the No. 2 brake actuator case collar to the brake actuator bolt cushion.

NOTICE:

Make sure that the No. 2 brake actuator case collar is in full contact with the brake actuator bolt cushion.



Hide 44510 3.INSTALL BRAKE ACTUATOR ASSEMBLY

a.

Install the brake actuator assembly to the brake actuator bracket assembly.


b.
C372683N01
0.448,0.865 0.604,1.063 0.156,0.198 10 false 1 1.031,1.146 1.146,1.333 0.115,0.188 10 true 2 2.438,1.604 2.594,1.802 0.156,0.198 10 false 3

Tighten the 2 nuts and install the bolt.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake tubes because the brake actuator assembly is filled with brake fluid.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.

·

Tighten the bolt and 2 nuts in the order shown in the illustration.




Hide 4.INSTALL BRAKE ACTUATOR WITH BRACKET

a.

w/ cushion:

i.
C373422C01
1.427,0.438 1.802,0.438 true 1.156,1.531 1.396,1.531 1.396,1.531 1.531,1.688 true 1.031,1.938 1.24,1.938 1.24,1.938 1.406,1.75 true 1.823,0.354 2.01,0.521 0.188,0.167 10 true *a 0.854,1.854 1.021,2.031 0.167,0.177 10 true *b 1,1.448 1.188,1.625 0.188,0.177 10 true *c
*a Stud Bolt
*b Cushion
*c Side Member


Temporarily install the brake actuator with bracket to the vehicle body.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:
·

Install the brake actuator with bracket while avoiding the brake lines.

·

After temporarily installing the brake actuator with bracket to the vehicle body, confirm that the cushion is contacting the upper side of the side member.




ii.
C372682N01
2.229,1.948 2.344,2.135 0.115,0.188 10 true 1 1.75,0.229 1.865,0.417 0.115,0.188 10 true 2 1.813,1.99 1.927,2.177 0.115,0.188 10 true 3

Install the 2 bolts and nut in the order shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

HINT:

Install the 2 bolts from the bottom of the vehicle.




b.

w/o cushion:

i.
C403030N01
2.229,1.948 2.344,2.135 0.115,0.188 10 true 1 1.75,0.229 1.865,0.417 0.115,0.188 10 true 2 1.813,1.99 1.927,2.177 0.115,0.188 10 true 3

Temporarily install the brake actuator with bracket to the vehicle body with the 2 bolts and nut.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:
·

Install the brake actuator with bracket while avoiding the brake lines.

·

Install the 2 bolts from the bottom of the vehicle.




ii.

Fully tighten the 2 bolts and nut in the order shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)



c.

Remove the protective tape.


d.
C373421

Engage the clamp to install a new brake tube clamp.


e.

Return the front No. 3 brake tube to its original position.

NOTICE:

Do not apply excessive force to the front No. 3 brake tube.



f.
C372679

Temporarily install the front No. 3 brake tube to the front flexible hose.

NOTICE:
·

Do not kink or damage the front No. 3 brake tube.

·

Do not allow any foreign matter such as dirt or dust to enter the front No. 3 brake tube from the connecting parts.




g.
C372681

Engage the clamp to connect the front No. 3 brake tube.

NOTICE:

Do not kink or damage the front No. 3 brake tube.



h.
C372686C01
1.604,0.677 1.99,0.677 true 1.448,0.594 1.604,0.771 0.156,0.177 10 true *a
*a To Front Wheel Cylinder Assembly LH


Temporarily tighten the brake line to the correct position on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.




i.
C372687C01
2.854,2.896 2.688,2.896 2.688,2.896 2.688,2.667 false 1.813,2.927 2.125,3.083 0.313,0.156 10 false *a 2.875,2.813 3.073,2.979 0.198,0.167 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten the brake line.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the brake line.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




j.
C372688C01
1.26,0.625 1.74,0.625 true 1.094,0.542 1.25,0.708 0.156,0.167 10 true *a
*a To Rear Wheel Cylinder Assembly RH


Temporarily tighten the brake line to the correct position on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.




k.
C372689C01
2.865,2.885 2.688,2.885 2.688,2.885 2.688,2.656 false 1.802,2.927 2.115,3.083 0.313,0.156 10 false *a 2.885,2.813 3.083,2.979 0.198,0.167 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten the brake line.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the brake line.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




l.
C372690C01
1.875,1.438 1.875,1.083 true 2.073,0.729 2.302,0.375 2.302,0.375 2.542,0.375 true 1.667,0.729 1.458,0.385 1.458,0.385 1.198,0.385 true 1,0.938 1.521,0.938 true 2.542,0.302 2.708,0.469 0.167,0.167 10 true *a 1.802,1.448 1.979,1.615 0.177,0.167 10 true *b 0.813,0.865 0.99,1.031 0.177,0.167 10 true *c 1.021,0.302 1.198,0.469 0.177,0.167 10 true *d
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly
*c To Front Wheel Cylinder Assembly RH
*d To Rear Wheel Cylinder Assembly LH


Temporarily tighten the 4 brake lines to the correct positions on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




m.
C372691C01
2.885,2.896 2.698,2.896 2.698,2.896 2.698,2.667 false 1.792,2.927 2.104,3.083 0.313,0.156 10 false *a 2.906,2.823 3.083,2.99 0.177,0.167 10 false *b 1.25,1.198 1.385,1.375 0.135,0.177 10 true B 1.844,0.375 1.979,0.552 0.135,0.177 10 true B 2.24,0.292 2.365,0.479 0.125,0.188 10 true A 2.021,1.344 2.146,1.531 0.125,0.188 10 true A
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten each brake line.

Torque:
Specified tightening torque (A) : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)
Specified tightening torque (B) : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the brake lines.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

(A): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

(B): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




n.
C372680C01
2.854,2.896 2.708,2.896 2.708,2.896 2.708,2.646 false 1.813,2.938 2.125,3.094 0.313,0.156 10 false *a 2.885,2.823 3.198,2.979 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten the front No. 3 brake tube while holding the front flexible hose with a wrench.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the front No. 3 brake tube.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




o.
C372676C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake actuator assembly and lock the lock lever.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the actuator connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter the connector.




Hide 53607A 5.INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY

a.
C377997N02
1,1.927 1.115,2.083 0.115,0.156 10 true A 2.448,1.927 2.552,2.073 0.104,0.146 10 true A 2.833,1.917 2.938,2.063 0.104,0.146 10 true B 0.594,1.917 0.708,2.063 0.115,0.146 10 true B

Temporarily install the front center upper suspension brace sub-assembly with the 6 bolts and 4 nuts.


b.

Fully tighten the 2 nuts (A).

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


c.

Fully tighten the 6 bolts and 2 nuts (B) to install the front center upper suspension brace sub-assembly.

Torque:
Bolt : 8.9 N*m (91 kgf*cm, 79 in.*lbf)
Nut (B) : 39 N*m (398 kgf*cm, 29 ft.*lbf)


d.

Engage the 2 clamps to install the wire harness.


e.

Connect the connector.


f.

w/ Windshield Deicer System:

i.

Engage the 3 clamps to install the wire harness.


ii.

Connect the connector.



g.

w/ Heated Windshield Defroster System:

i.

Engage the 5 clamps to install the wire harness.


ii.

Connect the 2 connectors.



Hide 55708 6.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 7.INSTALL FRONT WHEEL RH

Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

for 6AR-FSE: Click hereGeneral>MAINTENANCE>6AR-FSE BATTERY>INSTALLATION

for 2AR-FE: Click hereGeneral>MAINTENANCE>2AR-FE BATTERY>INSTALLATION

for A25A-FKS: Click hereGeneral>MAINTENANCE>A25A-FKS BATTERY>INSTALLATION

for 2GR-FKS: Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 9.BLEED BRAKE SYSTEM

Hide 10. PERFORM SYSTEM VARIANT LEARNING AND ACCELERATION SENSOR ZERO POINT CALIBRATION