Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module) › from 2019.10
RM33A0E _51 Engine / Hybrid System _065341 A25A-FKS ENGINE CONTROL _0328248 SFI SYSTEM(w/ Canister Pump Module) J

A25A-FKS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B, +B2 (BATT) terminals to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A256646E66
0.99,0.833 2.802,1.135 1.813,0.302 10 false from EFI-MAIN NO. 4 Fuse 0.938,1.177 2.698,1.531 1.76,0.354 10 false from EFI-MAIN NO. 1 Relay 0.135,1.969 2.625,2.469 2.49,0.5 10 false to Throttle Position Sensor, Accelerator Pedal Sensor Assembly, etc. (Sensors which have an IC) 0.135,2.646 2.563,3.031 2.427,0.385 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.969,3.094 5.313,3.406 0.344,0.313 10 false ECM 2.885,0.677 3.563,1 0.677,0.323 10 false BATT 2.823,1.042 3.49,1.292 0.667,0.25 10 false +B, +B2 3.063,2.021 3.427,2.25 0.365,0.229 10 false VC 4.396,0.875 6.188,1.229 1.792,0.354 10 false 5 V Constant Voltage Circuit 5.365,1.76 6.354,2.115 0.99,0.354 10 false Microprocessor 4.073,2.844 4.333,3.063 0.26,0.219 10 false R

When the VC circuit has a short circuit, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.

WIRING DIAGRAM

·

For the circuit diagram of the ECM power source refer to the ECM power source circuit.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>ECM Power Source Circuit

·

VC Output Circuit

A447608E05
0.229,2.781 0.688,2.979 0.458,0.198 10 false d4 0.219,0.677 1.802,1.438 1.583,0.76 10 false Throttle Body with Motor Assembly 0.219,2.979 2.021,3.417 1.802,0.438 10 false Crankshaft Position Sensor 0.219,4.635 1.854,5.146 1.635,0.51 10 false Camshaft Position Sensor (for Intake Camshaft) 0.219,4.458 0.677,4.656 0.458,0.198 10 false C18 0.219,6.333 1.865,6.906 1.646,0.573 10 false Camshaft Position Sensor (for Exhaust Camshaft) 0.219,0.5 0.677,0.698 0.458,0.198 10 false C27 2.563,0.573 3.021,0.771 0.458,0.198 10 false VC 2.583,1.135 3.042,1.333 0.458,0.198 10 false E2 2.427,2.219 2.885,2.417 0.458,0.198 10 false VTA2 2.479,1.667 2.938,1.865 0.458,0.198 10 false VTA 2.396,2.875 2.854,3.073 0.458,0.198 10 false VCNE 2.5,3.385 2.958,3.583 0.458,0.198 10 false NE- 2.49,3.917 2.948,4.115 0.458,0.198 10 false NE+ 2.563,4.542 3.021,4.74 0.458,0.198 10 false VC 2.479,5.063 2.938,5.26 0.458,0.198 10 false VVI- 2.458,5.615 2.917,5.813 0.458,0.198 10 false VVI+ 2.49,6.281 2.948,6.479 0.458,0.198 10 false VC2 2.427,6.792 2.885,6.99 0.458,0.198 10 false VVE- 2.396,7.354 2.854,7.552 0.458,0.198 10 false VVE+ 6.26,0.417 6.719,0.615 0.458,0.198 10 false 5 V 5.271,0.49 5.729,0.688 0.458,0.198 10 false VCTA 5.292,1.031 5.75,1.229 0.458,0.198 10 false ETA 5.281,1.677 5.74,1.875 0.458,0.198 10 false VTA1 5.271,2.198 5.729,2.396 0.458,0.198 10 false VTA2 5.281,2.771 5.74,2.969 0.458,0.198 10 false VCNE 5.292,3.302 5.75,3.5 0.458,0.198 10 false NE- 5.271,3.948 5.729,4.146 0.458,0.198 10 false NE+ 5.271,4.448 5.729,4.646 0.458,0.198 10 false VCV1 5.281,4.969 5.74,5.167 0.458,0.198 10 false VV1- 5.271,5.625 5.729,5.823 0.458,0.198 10 false VV1+ 5.271,6.177 5.729,6.375 0.458,0.198 10 false VCE1 5.26,6.698 5.719,6.896 0.458,0.198 10 false EV1- 5.271,7.344 5.729,7.542 0.458,0.198 10 false EV1+ 5.833,8.135 6.292,8.333 0.458,0.198 10 false ECM 2.865,0.51 3.323,0.708 0.458,0.198 10 false 2 2.854,1.01 3.313,1.208 0.458,0.198 10 false 4 2.854,1.573 3.313,1.771 0.458,0.198 10 false 1 2.854,2.094 3.313,2.292 0.458,0.198 10 false 3 2.865,2.781 3.323,2.979 0.458,0.198 10 false 3 2.865,3.281 3.323,3.479 0.458,0.198 10 false 2 2.854,3.833 3.313,4.031 0.458,0.198 10 false 1 2.854,4.458 3.313,4.656 0.458,0.198 10 false 3 2.844,4.979 3.302,5.177 0.458,0.198 10 false 2 2.844,5.51 3.302,5.708 0.458,0.198 10 false 1 2.844,6.177 3.302,6.375 0.458,0.198 10 false 3 2.833,6.708 3.292,6.906 0.458,0.198 10 false 2 2.833,7.24 3.292,7.438 0.458,0.198 10 false 1 0.229,6.167 0.688,6.365 0.458,0.198 10 false C77 4.885,0.417 5.344,0.615 0.458,0.198 10 false 109 4.896,0.958 5.354,1.156 0.458,0.198 10 false 110 4.896,1.5 5.354,1.698 0.458,0.198 10 false 108 4.938,2.031 5.396,2.229 0.458,0.198 10 false 87 4.896,2.708 5.354,2.906 0.458,0.198 10 false 116 4.896,3.229 5.354,3.427 0.458,0.198 10 false 115 4.948,3.781 5.406,3.979 0.458,0.198 10 false 93 4.927,4.385 5.385,4.583 0.458,0.198 10 false 88 4.927,4.896 5.385,5.094 0.458,0.198 10 false 89 4.938,5.448 5.396,5.646 0.458,0.198 10 false 90 4.875,6.115 5.333,6.313 0.458,0.198 10 false 113 4.896,6.635 5.354,6.833 0.458,0.198 10 false 114 4.917,7.177 5.375,7.375 0.458,0.198 10 false 91 4.896,0.604 5.604,0.823 0.708,0.219 10 false C57 4.896,1.135 5.604,1.354 0.708,0.219 10 false C57 4.896,1.677 5.604,1.896 0.708,0.219 10 false C57 4.896,2.219 5.604,2.438 0.708,0.219 10 false C57 4.896,2.885 5.604,3.104 0.708,0.219 10 false C57 4.896,3.406 5.604,3.625 0.708,0.219 10 false C57 4.896,3.948 5.604,4.167 0.708,0.219 10 false C57 4.896,4.563 5.604,4.781 0.708,0.219 10 false C57 4.896,5.083 5.604,5.302 0.708,0.219 10 false C57 4.896,5.625 5.604,5.844 0.708,0.219 10 false C57 4.885,6.292 5.594,6.51 0.708,0.219 10 false C57 4.885,6.813 5.594,7.031 0.708,0.219 10 false C57 4.885,7.354 5.594,7.573 0.708,0.219 10 false C57

A447609E07
0.219,4.948 1.813,5.469 1.594,0.521 10 false Accelerator Pedal Sensor Assembly 0.219,4.75 1.792,5.021 1.573,0.271 10 false A20 2.406,4.823 3.052,5.125 0.646,0.302 10 false VCPA 2.427,5.271 3.073,5.573 0.646,0.302 10 false VCP2 2.5,5.729 3.146,6.031 0.646,0.302 10 false EPA 2.417,6.156 3.063,6.458 0.646,0.302 10 false EPA2 2.49,6.604 3.135,6.906 0.646,0.302 10 false VPA 2.427,7.073 3.073,7.375 0.646,0.302 10 false VPA2 4.917,4.833 5.563,5.135 0.646,0.302 10 false A24 5.302,4.729 5.948,5.031 0.646,0.302 10 false VCPA 5.292,5.177 5.938,5.479 0.646,0.302 10 false VCP2 5.292,5.625 5.938,5.927 0.646,0.302 10 false EPA 5.302,6.083 5.948,6.385 0.646,0.302 10 false EPA2 5.313,6.625 5.958,6.927 0.646,0.302 10 false VPA 5.302,7.073 5.948,7.375 0.646,0.302 10 false VPA2 4.969,4.646 5.615,4.948 0.646,0.302 10 false 57 4.958,5.094 5.604,5.396 0.646,0.302 10 false 60 4.958,5.542 5.604,5.844 0.646,0.302 10 false 56 4.958,5.99 5.604,6.292 0.646,0.302 10 false 59 4.969,6.427 5.615,6.729 0.646,0.302 10 false 55 4.969,6.885 5.615,7.188 0.646,0.302 10 false 58 5.781,7.74 6.417,8 0.635,0.26 10 false ECM 0.24,2.656 2.063,3.292 1.823,0.635 10 false Oil Pressure and Temperature Sensor 0.24,2.448 1.813,2.719 1.573,0.271 10 false C110 2.573,2.521 2.885,2.719 0.313,0.198 10 false VC 2.427,4.042 3.042,4.24 0.615,0.198 10 false TOUT 2.406,3.542 3.021,3.74 0.615,0.198 10 false POUT 2.479,3.01 2.875,3.229 0.396,0.219 10 false GND 5.302,2.417 5.917,2.615 0.615,0.198 10 false VCPE 5.302,4.042 5.917,4.24 0.615,0.198 10 false THEO 5.302,3.531 5.76,3.729 0.458,0.198 10 false PEO 5.302,2.917 5.917,3.115 0.615,0.198 10 false EPEO 2.875,5.177 3.031,5.375 0.156,0.198 10 false 1 2.885,6.083 3.042,6.281 0.156,0.198 10 false 2 2.875,6.979 3.031,7.177 0.156,0.198 10 false 3 2.896,4.74 3.052,4.938 0.156,0.198 10 false 4 2.885,5.635 3.042,5.833 0.156,0.198 10 false 5 2.875,6.531 3.031,6.729 0.156,0.198 10 false 6 2.885,2.438 3.042,2.635 0.156,0.198 10 false 3 2.885,2.938 3.042,3.135 0.156,0.198 10 false 2 2.875,3.448 3.031,3.646 0.156,0.198 10 false 1 2.875,3.958 3.031,4.156 0.156,0.198 10 false 4 4.917,5.281 5.563,5.583 0.646,0.302 10 false A24 4.917,5.729 5.563,6.031 0.646,0.302 10 false A24 4.917,6.177 5.563,6.479 0.646,0.302 10 false A24 4.927,6.615 5.573,6.917 0.646,0.302 10 false A24 4.927,7.063 5.573,7.365 0.646,0.302 10 false A24 4.917,2.521 5.563,2.823 0.646,0.302 10 false C57 4.917,3.021 5.563,3.323 0.646,0.302 10 false C57 4.917,3.542 5.563,3.844 0.646,0.302 10 false C57 4.917,4.042 5.563,4.344 0.646,0.302 10 false C57 4.958,2.344 5.271,2.542 0.313,0.198 10 false 99 4.917,2.833 5.375,3.031 0.458,0.198 10 false 100 4.917,3.354 5.375,3.552 0.458,0.198 10 false 122 4.917,3.865 5.375,4.063 0.458,0.198 10 false 123 4.927,0.698 5.573,1 0.646,0.302 10 false C57 4.927,1.188 5.573,1.49 0.646,0.302 10 false C57 4.917,1.677 5.563,1.979 0.646,0.302 10 false C57 0.271,0.781 2.104,1.24 1.833,0.458 10 false Manifold Absolute Pressure Sensor 0.26,0.604 0.719,0.802 0.458,0.198 10 false C28 2.594,0.698 2.906,0.896 0.313,0.198 10 false VC 2.625,1.188 2.938,1.385 0.313,0.198 10 false E2 2.542,1.688 3,1.885 0.458,0.198 10 false PIM 2.875,0.604 3.031,0.802 0.156,0.198 10 false 3 2.875,1.083 3.031,1.281 0.156,0.198 10 false 1 2.875,1.573 3.031,1.771 0.156,0.198 10 false 2 5.302,0.594 5.917,0.792 0.615,0.198 10 false VCPM 5.302,1.083 5.917,1.281 0.615,0.198 10 false EPIM 5.302,1.667 5.76,1.865 0.458,0.198 10 false PIM 4.927,0.51 5.385,0.708 0.458,0.198 10 false 121 4.917,1.01 5.375,1.208 0.458,0.198 10 false 119 4.938,1.5 5.396,1.698 0.458,0.198 10 false 120

A450186E03
0.344,0.771 0.802,0.969 0.458,0.198 10 false C20 0.344,0.99 1.698,1.885 1.354,0.896 10 false Mass Air Flow Meter Sub-assembly 2.573,0.76 3.031,0.958 0.458,0.198 10 false 5V 2.5,1.25 2.958,1.448 0.458,0.198 10 false E2G 2.563,1.771 3.021,1.969 0.458,0.198 10 false FG 2.5,2.281 2.958,2.479 0.458,0.198 10 false THA 2.896,0.646 3.354,0.844 0.458,0.198 10 false 3 2.906,1.146 3.365,1.344 0.458,0.198 10 false 2 2.896,1.656 3.354,1.854 0.458,0.198 10 false 1 2.906,2.167 3.365,2.365 0.458,0.198 10 false 4 4.917,0.771 5.344,0.938 0.427,0.167 10 false C57 4.917,1.271 5.344,1.438 0.427,0.167 10 false C57 4.917,1.792 5.344,1.958 0.427,0.167 10 false C57 4.917,2.292 5.344,2.458 0.427,0.167 10 false C57 5,0.552 5.458,0.75 0.458,0.198 10 false 78 4.979,1.052 5.438,1.25 0.458,0.198 10 false 79 4.938,1.563 5.396,1.76 0.458,0.198 10 false 101 4.938,2.073 5.396,2.271 0.458,0.198 10 false 102 5.323,0.677 5.75,0.844 0.427,0.167 10 false VCVG 5.323,1.167 5.75,1.333 0.427,0.167 10 false E2G 5.323,1.781 5.75,1.948 0.427,0.167 10 false VG 5.313,2.281 5.74,2.448 0.427,0.167 10 false THA 0.344,2.938 0.802,3.135 0.458,0.198 10 false d1 0.333,3.125 1.917,3.896 1.583,0.771 10 false Fuel Pressure Sensor (for High Pressure Side) 2.583,2.958 3.042,3.156 0.458,0.198 10 false VC 2.604,3.438 3.063,3.635 0.458,0.198 10 false E2 2.594,3.948 3.052,4.146 0.458,0.198 10 false PR 2.896,2.844 3.354,3.042 0.458,0.198 10 false 1 2.917,3.344 3.375,3.542 0.458,0.198 10 false 2 2.906,3.823 3.365,4.021 0.458,0.198 10 false 3 4.917,2.969 5.344,3.135 0.427,0.167 10 false C57 4.917,3.458 5.344,3.625 0.427,0.167 10 false C57 4.917,3.958 5.344,4.125 0.427,0.167 10 false C57 5.313,2.875 5.74,3.042 0.427,0.167 10 false VCPR 5.323,3.365 5.75,3.531 0.427,0.167 10 false EPR 5.313,3.917 5.74,4.083 0.427,0.167 10 false PR 4.969,2.771 5.427,2.969 0.458,0.198 10 false 98 4.979,3.26 5.438,3.458 0.458,0.198 10 false 96 4.969,3.75 5.427,3.948 0.458,0.198 10 false 97 0.354,4.615 0.813,4.813 0.458,0.198 10 false F12 0.344,4.813 1.927,5.583 1.583,0.771 10 false Fuel Pressure Sensor (for Low Pressure Side) 2.583,4.594 3.042,4.792 0.458,0.198 10 false VC 2.604,5.094 3.063,5.292 0.458,0.198 10 false E2 2.521,5.563 2.979,5.76 0.458,0.198 10 false PFL 2.927,4.469 3.385,4.667 0.458,0.198 10 false 1 2.927,4.948 3.385,5.146 0.458,0.198 10 false 2 2.917,5.448 3.375,5.646 0.458,0.198 10 false 3 4.917,4.594 5.344,4.76 0.427,0.167 10 false C57 4.917,5.083 5.344,5.25 0.427,0.167 10 false C57 4.917,5.583 5.344,5.75 0.427,0.167 10 false C57 4.958,4.385 5.417,4.583 0.458,0.198 10 false 84 4.969,4.865 5.427,5.063 0.458,0.198 10 false 61 4.938,5.354 5.396,5.552 0.458,0.198 10 false 107 5.323,4.5 5.75,4.667 0.427,0.167 10 false VCPF 5.313,4.99 5.74,5.156 0.427,0.167 10 false EPFL 5.323,5.552 5.75,5.719 0.427,0.167 10 false PFL 0.354,6.323 0.813,6.521 0.458,0.198 10 false R45 0.344,6.521 2.229,7.208 1.885,0.688 10 false Canister Pressure Sensor 2.49,6.313 2.948,6.51 0.458,0.198 10 false VCC 2.385,6.802 2.844,7 0.458,0.198 10 false SGND 2.406,7.292 2.865,7.49 0.458,0.198 10 false VOUT 2.927,6.188 3.385,6.385 0.458,0.198 10 false 6 2.927,6.677 3.385,6.875 0.458,0.198 10 false 8 2.927,7.177 3.385,7.375 0.458,0.198 10 false 7 4.927,6.313 5.354,6.479 0.427,0.167 10 false A24 4.917,6.802 5.344,6.969 0.427,0.167 10 false A24 4.927,7.292 5.354,7.458 0.427,0.167 10 false A24 4.969,6.104 5.427,6.302 0.458,0.198 10 false 48 4.969,6.594 5.427,6.792 0.458,0.198 10 false 49 4.958,7.094 5.417,7.292 0.458,0.198 10 false 50 5.333,6.219 5.896,6.396 0.563,0.177 10 false VCPP 5.333,6.698 5.896,6.875 0.563,0.177 10 false EPPM 5.333,7.271 5.896,7.448 0.563,0.177 10 false PPMP 5.813,7.99 6.583,8.385 0.771,0.396 10 false ECM


CAUTION / NOTICE / HINT

NOTICE:

Check the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

2.CHECK EFI NO. 1 FUSE VOLTAGE

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK EFI NO. 1 FUSE VOLTAGE
A402426C01
2.083,0.76 2.698,0.292 true 0.156,0.208 0.469,0.406 0.313,0.198 10 false *1 2.729,0.188 3.042,0.385 0.313,0.198 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 EFI NO. 1 Fuse


a.

Turn the engine switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (EFI NO. 1 fuse) - Body ground Engine switch on (IG) 11 to 14 V


HINT:
·

Check the fuse with it installed to the engine room relay block and junction block assembly.

·

If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.




Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)

NG

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle body with motor assembly connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION



A

4.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

4.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

5.CHECK CONNECTION BETWEEN GTS AND ECM (CRANKSHAFT POSITION SENSOR)

B

REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY

5.CHECK CONNECTION BETWEEN GTS AND ECM (CRANKSHAFT POSITION SENSOR)
a.

Disconnect the crankshaft position sensor connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

6.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))

B

6.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))
a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

7.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)

B

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

7.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

8.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))

B

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

8.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))
a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

9.CHECK CONNECTION BETWEEN GTS AND ECM (ENGINE OIL PRESSURE AND TEMPERATURE SENSOR)

B

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

9.CHECK CONNECTION BETWEEN GTS AND ECM (ENGINE OIL PRESSURE AND TEMPERATURE SENSOR)
a.

Disconnect the engine oil pressure and temperature sensor connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

10.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE))

B

REPLACE ENGINE ENGINE OIL PRESSURE AND TEMPERATURE SENSOR

10.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE))
a.

Disconnect the fuel pressure sensor (for high pressure side) connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor (for high pressure side).

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION



A

11.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FUEL DELIVERY PIPE WITH SENSOR SUB-ASSEMBLY) (FOR LOW PRESSURE SIDE))

B

REPLACE FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE)

11.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR (FUEL DELIVERY PIPE WITH SENSOR SUB-ASSEMBLY) (FOR LOW PRESSURE SIDE))
a.

Disconnect the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side) connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side).

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION



A

12.CHECK CONNECTION BETWEEN GTS AND ECM (MASS AIR FLOW METER SUB-ASSEMBLY)

B

REPLACE FUEL PRESSURE SENSOR (FUEL DELIVERY PIPE WITH SENSOR SUB-ASSEMBLY) (FOR LOW PRESSURE SIDE)

12.CHECK CONNECTION BETWEEN GTS AND ECM (MASS AIR FLOW METER SUB-ASSEMBLY)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION



A

13.CHECK CONNECTION BETWEEN GTS AND ECM (CANISTER PUMP MODULE)

B

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

13.CHECK CONNECTION BETWEEN GTS AND ECM (CANISTER PUMP MODULE)
a.

Disconnect the canister pump module connector.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

14.CHECK HARNESS AND CONNECTOR

B

14.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the accelerator pedal sensor assembly connector.


c.

Disconnect the crankshaft position sensor connector.


d.

Disconnect the camshaft position sensor (for intake camshaft) connector.


e.

Disconnect the manifold absolute pressure sensor connector.


f.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


g.

Disconnect the engine oil pressure and temperature sensor connector.


h.

Disconnect the fuel pressure sensor (for high pressure side) connector.


i.

Disconnect the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side) connector.


j.

Disconnect the mass air flow meter sub-assembly connector.


k.

Disconnect the ECM connectors.


l.

Disconnect the canister pump module connector.


m.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C57-109 (VCTA) - Body ground Always 10 kΩ or higher
C57-116 (VCNE) - Body ground Always 10 kΩ or higher
C57-88 (VCV1) - Body ground Always 10 kΩ or higher
C57-113 (VCE1) - Body ground Always 10 kΩ or higher
C57-121 (VCPM) - Body ground Always 10 kΩ or higher
C57-99 (VCPE) - Body ground Always 10 kΩ or higher
A24-57 (VCPA) - Body ground Always 10 kΩ or higher
A24-60 (VCP2) - Body ground Always 10 kΩ or higher
C57-78 (VCVG) - Body ground Always 10 kΩ or higher
C57-98 (VCPR) - Body ground Always 10 kΩ or higher
C57-84 (VCPF) - Body ground Always 10 kΩ or higher
A24-48 (VCPP) - Body ground Always 10 kΩ or higher



n.

Measure the resistance according to the value(s) in the table below.

HINT:

Remove the VVT, EFI-MAIN NO. 2 and EFI-MAIN NO. 3 relays connected between the checked terminals as the coil inside the relay influences the measurement value.


Standard Resistance:
Tester Connection Condition Specified Condition
A24-9 (+B) - 1 (EFI NO. 1 fuse) Always Below 1 Ω
A24-35 (+B2) - 1 (EFI NO. 1 fuse) Always Below 1 Ω
A24-9 (+B) - Body ground Always 10 kΩ or higher
A24-35 (+B2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR