Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › CAMSHAFT OIL CONTROL VALVE (for Intake Side of Bank 2) › 2020.02–2021.02
RM33A0E _51 Engine / Hybrid System _065332 2GR-FKS ENGINE CONTROL _0326373 CAMSHAFT OIL CONTROL VALVE(for Intake Side of Bank 2) A

2GR-FKS ENGINE CONTROL  CAMSHAFT OIL CONTROL VALVE(for Intake Side of Bank 2)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during camshaft timing gear bolt removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Departure Alert System (w/ Steering Control) (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
Gas leak from exhaust system is repaired Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for Initialization
(Click here)
for Registration
Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
for Initialization
(Click here)
for Calibration
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic view monitor system (Click here)
for Initialization
(Click here)
for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)

PROCEDURE

Hide 1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 15370 2.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2)

Hide 3.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A368570C01
1.698,1.292 2.188,1.292 true 1.469,1.313 1.198,1.719 1.198,1.719 0.958,1.719 true 2.198,1.198 2.375,1.396 0.177,0.198 10 true *a 0.781,1.646 0.958,1.844 0.177,0.198 10 true *b
*a Timing Mark
*b Timing Mark (Cutout)


Turn the crankshaft pulley clockwise until its timing mark (cutout) is aligned with the timing mark on the timing chain cover assembly as shown in the illustration.


b.

Check that the cutout of the camshaft timing gear assembly is at the top.

A395722C01
2.885,0.781 3.208,0.479 3.208,0.479 3.396,0.479 true 2.219,3.552 2.448,3.552 2.448,3.552 2.719,3.281 true 5.125,3.323 5.125,3.167 5.125,3.167 5.365,3.042 true 5.208,0.896 5.667,0.896 true 0.885,1.104 1.198,1.26 0.313,0.156 10 false *a 0.917,2.906 1.229,3.063 0.313,0.156 10 false *b 5.698,0.792 5.938,1.01 0.24,0.219 10 true *c 1.76,0.823 1.99,1.052 0.229,0.229 10 true *d 5.073,3.323 5.385,3.479 0.313,0.156 10 false *c 1.99,3.479 2.208,3.667 0.219,0.188 10 true *c 3.427,0.375 3.667,0.563 0.24,0.188 10 true *c 1.75,2.656 1.979,2.885 0.229,0.229 10 true *d
*a Correct *b Incorrect
*c Cutout *d Up


HINT:

If the cutout of the camshaft timing gear assembly is not at the top, turn the crankshaft 360° clockwise and align the timing mark (cutout) of the crankshaft pulley with the timing mark on the timing chain cover assembly again.



Hide 4.REMOVE CAMSHAFT TIMING GEAR BOLT

a.
A408185

While holding the crankshaft pulley, remove the camshaft timing gear bolt.

NOTICE:
·

If the camshaft timing gear bolt has been struck or dropped, replace it.

·

Do not turn the crankshaft pulley after removing the camshaft timing gear bolt.