Home › Engine / Hybrid System › A25A-FKS (EMISSION CONTROL) › EGR VALVE › from 2020.08
RM33A0E _51 Engine / Hybrid System _065344 A25A-FKS EMISSION CONTROL _0328566 EGR VALVE A

A25A-FKS EMISSION CONTROL  EGR VALVE  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 25620 1.SET EGR VALVE ASSEMBLY

a.

Set the EGR valve assembly to the camshaft housing.

HINT:

At this time, do not install the parts with bolts.



b.

Install the No. 4 water by-pass hose to the EGR valve assembly and slide the clip to secure it.


c.

Connect the No. 8 water by-pass hose to the EGR valve assembly and slide the clip to secure it.


Hide 25680 2.INSTALL EGR COOLER ASSEMBLY

a.
A472569C02
1.156,1.906 0.792,2.021 0.792,2.021 1.042,1.813 false 0.917,1.604 0.542,1.417 0.542,1.417 0.979,1.458 false 2.458,0.635 2.458,1.104 2.458,1.104 2.146,0.708 false 2.427,0.385 2.021,0.177 2.021,0.177 2.125,0.469 false 0.313,1.292 0.594,1.573 0.281,0.281 10 false *a 0.573,1.979 0.823,2.177 0.25,0.198 10 false *a 2.448,1.146 2.698,1.344 0.25,0.198 10 false *a 1.781,0.073 2.104,0.344 0.323,0.271 10 false *a
*a Claw


Install a new EGR cooler gasket to the EGR cooler assembly.

NOTICE:

Make sure that the claws of the EGR cooler gasket are toward the EGR cooler assembly side.



b.

Install a new EGR valve gasket to the EGR cooler assembly.

NOTICE:

Make sure that the claws of the EGR valve gasket are toward the EGR cooler assembly side.



c.
A472585C02
1.333,1.802 1.563,2.031 0.229,0.229 10 true 1 2.677,1.76 3.063,2.042 0.385,0.281 10 true 3 *a 2.885,1.396 3.115,1.625 0.229,0.229 10 true 2 1.854,0.51 2.063,0.698 0.208,0.188 10 true 4 0.458,0.74 0.667,0.927 0.208,0.188 10 true 5
*a Bolt or Nut


Type A:

i.

Temporarily install the EGR cooler assembly to the cylinder head sub-assembly and EGR valve assembly with the 3 bolts and 2 nuts.


ii.

Tighten the 3 bolts and 2 nuts in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)



d.

Type B:

i.

Temporarily install the EGR cooler assembly to the cylinder head sub-assembly and EGR valve assembly with the 2 bolts and 3 nuts.


ii.

Tighten the 2 bolts and 3 nuts in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)



e.

Connect the No. 3 water by-pass hose and No. 4 water by-pass hose to the EGR cooler assembly and slide the 2 clips to secure them.


Hide 25620 3.INSTALL EGR VALVE ASSEMBLY

a.

Using an 8 mm socket wrench, install the EGR valve assembly to the camshaft housing with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25601 4.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

a.

Install a new EGR inlet gasket to the intake manifold.


b.

Install a new EGR valve adapter gasket to the No. 1 EGR pipe sub-assembly.


c.

Using an 8 mm socket wrench, install the No. 1 EGR pipe sub-assembly to the intake manifold and EGR valve assembly with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 5.CONNECT ENGINE WIRE

a.

Engage the 2 wire harness clamps to connect the engine wire.


b.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the EGR valve assembly connector.


d.

Connect the No. 5 engine wire connector.


Hide 6.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 12601B 7.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 8.ADD ENGINE COOLANT