The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
12372A
1.INSTALL ENGINE MOUNTING INSULATOR LH
Perform this procedure only when replacement of the engine mounting insulator LH is necessary.
Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>INSTALLATION
12304
2.INSTALL ENGINE MOUNTING BRACKET SUB-ASSEMBLY LH
Perform this procedure only when replacement of the engine mounting bracket sub-assembly LH is necessary.
Temporarily tighten the bolt (A), and then fully tighten the 4 bolts in the order of (B), (C), (D) and (A).
Make sure that there is no gap between the engine mounting bracket sub-assembly LH and vehicle body before tightening the bolts.
12341
3.INSTALL ENGINE MOUNTING SPACER
Perform this procedure only when replacement of the engine mounting spacer is necessary.
Install the engine mounting spacer to the vehicle body with the 2 bolts.
Temporarily tighten the bolt (A), and then fully tighten the 2 bolts in the order of (B) and (A).
12305
4.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
Install the engine mounting insulator sub-assembly RH with the 2 bolts and nut.
Temporarily tighten the bolt (A), and then fully tighten the 2 bolts and nut in the order of (B), (A) and (C).
Engage the clamp.
Connect the No. 1 bond cable to the engine mounting insulator sub-assembly RH with the bolt.
Connect the bracket to the engine mounting insulator sub-assembly RH with the bolt.
Install the radiator reserve tank assembly with the bolt and nut in the order shown in the illustration.
Engage the clamp.
Connect the No. 6 water by-pass hose.
5.INSTALL ENGINE HANGERS
6.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND
Remove the engine assembly from the engine stand.
82121
7.INSTALL ENGINE WIRE
Install the engine wire to the engine assembly.
19315
8.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE
32101
9.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
30500
10.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY
28100
11.INSTALL STARTER ASSEMBLY
11363A
12.INSTALL FLYWHEEL HOUSING SIDE COVER
12311A
13.INSTALL FRONT ENGINE MOUNTING BRACKET
12371A
14.INSTALL REAR ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the rear engine mounting insulator is necessary.
12361A
15.INSTALL FRONT ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the front engine mounting insulator is necessary.
Install the front engine mounting insulator to the front frame assembly with the 3 nuts.
51100G
16.INSTALL FRONT FRAME ASSEMBLY
Install the rear engine mounting insulator to the front frame assembly with the 4 nuts.
Install the front engine mounting insulator to the front engine mounting bracket with the bolt.
17.CONNECT WIRE HARNESS
45319
18.INSTALL STEERING GEAR HEAT INSULATOR
35104V
19.INSTALL BREATHER PLUG HOSE
16260
20.CONNECT WATER BY-PASS HOSE ASSEMBLY
16261G
21.INSTALL FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE)
22.CONNECT VACUUM HOSE
32101A
23.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
11361J
24.INSTALL FLYWHEEL HOUSING UNDER COVER
Install the flywheel housing under cover to the cylinder block sub-assembly.
25.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
Perform inspection after repair after replacing the engine assembly.
w/ Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION
w/o Canister Pump Module
Set the engine assembly with transaxle on an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger.
Install the fuel delivery guard to the engine mounting bracket RH with the bolt.
Operate the engine lifter and install the engine assembly with transaxle to the vehicle.
Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.
|
Bolt |
|
Nut |
Install the front bumper extension sub-assembly RH and front bumper extension sub-assembly LH to the front frame assembly and vehicle body with the 8 bolts.
Install the front suspension member bracket sub-assembly RH and front suspension member bracket sub-assembly LH to the front frame assembly and vehicle body with the 4 bolts and 2 nuts.
Install the engine mounting insulator LH to the engine mounting bracket sub-assembly LH with the bolt and nut.
While holding the bolt in place, tighten the nut.
Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 3 bolts and nut.
Install the body mounting plate with the 6 bolts.
Engage the clamp.
26.INSTALL FRONT DRIVE SHAFT ASSEMBLY
17410
27.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
45220
28.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY
16281F
29.CONNECT NO. 5 WATER BY-PASS HOSE
Engage the clamp.
Connect the No. 5 water by-pass hose to the No. 3 water by-pass pipe and slide the clip to secure it.
30.CONNECT WIRE HARNESS
Connect the wire harness to the vehicle body with the bolt.
Connect the earth wire to the automatic transaxle assembly with the bolt.
Connect the wire harness to the positive (+) battery terminal with the nut.
Engage the 3 clamps.
Engage the claw to install the wire harness to the engine room relay block and junction block assembly.
Connect the 4 connectors to the engine room relay block and junction block assembly.
Install the nut to the engine room relay block and junction block assembly.
Install the engine room relay block and junction block assembly cover to the engine room relay block and junction block assembly.
88711
31.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY
88704
32.CONNECT SUCTION HOSE SUB-ASSEMBLY
16572D
33.CONNECT NO. 2 RADIATOR HOSE
Connect the No. 2 radiator hose to the water inlet and slide the clip to secure it.
16571C
34.CONNECT NO. 1 RADIATOR HOSE
Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.
Connect the No. 1 radiator hose to the No. 1 radiator bracket with the clamp.
23901
35.CONNECT FUEL TUBE SUB-ASSEMBLY
Connect the fuel tube sub-assembly.
Connect the fuel tube sub-assembly to the fuel pipe.
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
Install the No. 1 fuel pipe clamp to the fuel tube connector.
87245
36.CONNECT INLET HEATER HOSE
| *a | Protrusion |
| *b | Cutout |
Align the protrusions of the inlet heater hose connector with the cutouts in the flow shutting valve (water by-pass hose assembly) and push them together until the inlet heater hose connector makes a "click" sound.
| *a | Retainer |
|
Push |
|
Push in |
Push in the retainer.
Check that the flow shutting valve (water by-pass hose assembly) and inlet heater hose connector are securely connected by pulling on them.
87246
37.CONNECT OUTLET HEATER HOSE
| *a | Protrusion |
| *b | Cutout |
Align the protrusion of the No. 2 water by-pass pipe sub-assembly with the cutout in the outlet heater hose connector and push them together until the outlet heater hose makes a "click" sound.
| *a | Retainer |
|
Push |
|
Push in |
Push in the retainer.
Check that the No. 2 water by-pass pipe sub-assembly and outlet heater hose connector are securely connected by pulling on them.
44773F
38.CONNECT UNION TO CHECK VALVE HOSE
Connect the union to check valve hose to the vacuum pump assembly and slide the clip to secure it.
23826
39.CONNECT NO. 1 FUEL VAPOR FEED HOSE
Connect the No. 1 fuel vapor feed hose to the No. 1 vacuum switching valve assembly and slide the clip to secure it.
33820B
40.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.
| *a | Correct |
| *b | Incorrect |
Connect the transmission control cable assembly to the transmission control shaft lever as shown in the illustration.
Before installing the transmission control cable assembly, check that the park/neutral position switch assembly and shift lever are in N.
74404A
41.INSTALL BATTERY CLAMP SUB-ASSEMBLY
Install the battery clamp sub-assembly with the 3 bolts.
Engage the 4 clamps to the battery clamp sub-assembly.
42.INSTALL BATTERY
89661
43.INSTALL ECM
44.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE
| *a | Protrusion |
| *b | Cutout |
| *c | Top |
| *d | Front of Vehicle |
| *e | Locked |
| *f | Unlocked |
Install the air cleaner assembly with air cleaner hose to the throttle body with motor assembly and unlock the hose clip to secure it as shown in the illustration.
Align the cutout of the air cleaner hose with the protrusion of the throttle body with motor assembly.
| *a | Top |
| *b | Front of Vehicle |
| *c | 45°(Claw of Clip Location) |
| *d | Paint Mark |
Connect the No. 2 ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.
Make sure to position the clip as shown in the illustration.
| *a | Air Cleaner Support |
Insert the 3 pins of the air cleaner assembly into the 3 air cleaner supports as shown in the illustration.
Insert the 3 pins of the air cleaner assembly into the 3 air cleaner supports at the same time.
Check that the 3 pins are securely inserted into the 3 air cleaner supports.
Engage the vacuum hose to the air cleaner hose.
Engage the 3 wire harness clamps.
Connect the mass air flow meter sub-assembly connector.
17750A
45.INSTALL INLET AIR CLEANER ASSEMBLY
Install the inlet air cleaner assembly with the 2 bolts in the order shown in the illustration.
12601B
46.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
Engage the 3 clips to install the No. 1 engine cover sub-assembly.
47.INSPECT VACUUM HOSES
Inspect the vacuum hoses.
48.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
49.ADD ENGINE OIL
50.ADD ENGINE COOLANT
51.ADD AUTOMATIC TRANSAXLE FLUID
52.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
53. WARM UP ENGINE
54.INSPECT SHIFT LEVER POSITION
55.ADJUST SHIFT LEVER POSITION
56.INSPECT FOR ENGINE OIL LEAK
57.INSPECT FOR COOLANT LEAK
58.INSPECT FOR REFRIGERANT LEAK
59.INSPECT FOR FUEL LEAK
60.INSPECT FOR EXHAUST GAS LEAK
61.CHECK ENGINE OIL LEVEL
62.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR
52618
63.INSTALL FRONT LOWER BUMPER ABSORBER
Engage the 2 claws to install the front lower bumper absorber.
Install the 4 bolts.
52119A
64.INSTALL FRONT BUMPER COVER
53737B
65.INSTALL FRONT FENDER APRON SEAL LH
Install the front fender apron seal LH with the 2 screws and clip.
53736
66.INSTALL FRONT FENDER APRON SEAL RH
Install the front fender apron seal RH with the 2 screws and clip.
67.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY
Install the No. 2 engine under cover assembly with the 4 screws and 6 clips.
51441
68.INSTALL NO. 1 ENGINE UNDER COVER
Install the No. 1 engine under cover with the bolt, 6 screws and 2 clips.
53852K
69.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH
Install the front wheel opening extension pad LH with the 3 screws.
53851M
70.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH
Install the front wheel opening extension pad RH with the 3 screws.
71.INSTALL FRONT WHEELS
72. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
73.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
74.PERFORM INITIALIZATION
75.INSPECT IGNITION TIMING
76.INSPECT ENGINE IDLE SPEED
77.INSPECT CO/HC
78.CHECK SPEED SENSOR SIGNAL