Home › Engine / Hybrid System › A25A-FKS (INTAKE / EXHAUST) › INTAKE MANIFOLD › from 2020.08
RM33A0E _51 Engine / Hybrid System _065345 A25A-FKS INTAKE / EXHAUST _0328575 INTAKE MANIFOLD A

A25A-FKS INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during intake manifold removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of throttle body assembly

·

Cleaning the deposits from the throttle body assembly

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 53295E 1.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 17750A 2.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 22030 3.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 25601 5.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 89421 6.REMOVE E.F.I. VACUUM SENSOR ASSEMBLY (MANIFOLD ABSOLUTE PRESSURE SENSOR)

Hide 82121 7.DISCONNECT ENGINE WIRE

a.
A402241

Remove the bolt.


b.

Disengage the wire harness clamp and disconnect the engine wire.


Hide 16278 8.REMOVE NO. 2 WATER BY-PASS PIPE

a.
A402242N01
0.896,1.802 1.052,2 0.156,0.198 10 true A 1.51,1.927 1.698,2.094 0.188,0.167 10 true B 0.802,0.302 0.958,0.5 0.156,0.198 10 true A

Using an 8 mm socket wrench, remove the 2 bolts (A) and separate the No. 2 water by-pass pipe from the intake manifold.


b.

Remove the bolt (B) and No. 2 water by-pass pipe from the cylinder block sub-assembly.


Hide 16279 9.DISCONNECT NO. 3 WATER BY-PASS PIPE

a.
A402243

Slide the clip and disconnect the No. 5 water by-pass hose from the No. 3 water by-pass pipe.


b.

Using an 8 mm socket wrench, remove the bolt and disconnect the No. 3 water by-pass pipe from the intake manifold.


Hide 23820 10.DISCONNECT NO. 2 FUEL VAPOR FEED HOSE

a.
A402244

Disconnect the No. 2 fuel vapor feed hose from the intake manifold.


Hide 17111 11.REMOVE INTAKE MANIFOLD

a.
A402245

w/o Stud Bolt:

i.

Remove the 5 bolts and intake manifold from the cylinder head sub-assembly.



b.
A433689

w/ Stud Bolt:

i.

Remove the 3 bolts and 2 nuts.


ii.
A433690

Using an E8 "TORX" socket wrench, remove the 2 stud bolts and intake manifold from the cylinder head sub-assembly.



Hide 17177 12.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

a.
A402246

Remove the No. 1 intake manifold to head gasket from the intake manifold.


Hide 12611B 13.REMOVE NO. 1 ENGINE COVER

a.
A402247

Remove the clip and No. 1 engine cover.


Hide 14.REMOVE VACUUM HOSE

a.
A398018

Remove the vacuum hose from the intake manifold.