Home › Engine / Hybrid System › A25A-FKS (FUEL) › FUEL PUMP (for High Pressure) › 2020.08–2021.02
RM33A0E _51 Engine / Hybrid System _065343 A25A-FKS FUEL _0319399 FUEL PUMP(for High Pressure) A

A25A-FKS FUEL  FUEL PUMP(for High Pressure)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Replacement of fuel pump assembly

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)for A25A-FKS (w/ Canister Pump Module)
(Click here)for A25A-FKS (w/ Canister Pump Module)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A357489

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.



NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 25620 4.REMOVE EGR VALVE ASSEMBLY

Hide 23910A 6.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A401716

Disconnect the fuel tube sub-assembly from the fuel pump assembly.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23801P 7.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A401830

Disconnect the ignition coil connector.


b.

for EGR Valve Bracket Connection Type:

i.
A401717

Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.



c.

for Cylinder Head Cover Sub-assembly Connection Type:

i.
A463926C01
0,0 0,0 false
V100135

Union Nut
V100136

Bolt


Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.


ii.

Using an 8 mm socket wrench, remove the bolt.



d.
A401718

Loosen the 2 bolts of the fuel pump assembly.


e.

Remove the No. 1 fuel pipe sub-assembly from the fuel delivery pipe and fuel pump assembly.


Hide 23100X 8.REMOVE FUEL PUMP ASSEMBLY

NOTICE:

When replacing the fuel pump assembly, it is necessary to replace the No. 1 fuel pipe sub-assembly with a new one.


a.
A401719

Disconnect the fuel pump assembly connector.


b.
A401720

Remove the 2 bolts, fuel pump assembly and fuel pump flange from the cylinder head cover sub-assembly.


c.
A401723

Remove the O-ring from the fuel pump assembly.


d.
A401721

Remove the fuel pump lifter assembly from the fuel pump lifter guide.


e.
A401722

Remove the fuel pump spacer gasket from the cylinder head cover sub-assembly.