Home › Drivetrain › K120 (CVT) › TRANSMISSION CONTROL CABLE › from 2021.02
RM33A0E _52 Drivetrain _098634 K120 CVT _0461788 TRANSMISSION CONTROL CABLE A

K120 CVT  TRANSMISSION CONTROL CABLE  INSTALLATION  


PROCEDURE

Hide 33820B 1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

Before installing the transmission control cable assembly, check that the shift lever is in N.


a.
C420965C01
0.49,1.448 0.708,1.656 0.219,0.208 10 true *a
*a N


Turn the transmission control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.

NOTICE:
C416210C01
1.615,0.552 1.823,0.25 1.823,0.25 1.99,0.25 true 1.958,1.344 2.25,0.938 2.25,0.938 2.729,0.938 true 1.531,1.813 1.99,1.813 true 2.042,0.146 2.323,0.385 0.281,0.24 10 false *1 2.792,0.813 3.073,1.052 0.281,0.24 10 false *a 1.323,1.708 1.521,1.938 0.198,0.229 10 true *b
*1 Transmission Control Shaft Lever
*a Manual Valve Link Lever Sub-assembly
*b Manual Valve


If the transmission control shaft lever is turned counterclockwise more than necessary, manual valve link lever sub-assembly may separate from the manual valve.



b.

Pass the transmission control cable assembly into the vehicle and install the transmission control cable assembly to the vehicle body with the 2 nuts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


c.

Connect the transmission control cable assembly to vehicle body with the 2 nuts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


d.

Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


e.
C413828C01
0.354,2.104 0.625,2.333 0.271,0.229 10 false *a 1.771,2.104 2.01,2.302 0.24,0.198 10 false *b
*a Correct
*b Incorrect


Connect the transmission control cable assembly to the transmission control shaft lever as shown in the illustration.


f.
C400603C02
1.646,1.198 1.844,1.594 1.844,1.594 2,1.594 false 1.313,1.344 1.583,1.594 0.271,0.25 10 false *a 2.042,1.49 2.333,1.708 0.292,0.219 10 false *b
*a Slide
*b Adjuster Case Cover


Slide the adjuster case cover in the direction shown by the arrow.


g.
C400817C02
1.115,4.052 1.323,4.052 1.323,4.052 1.708,3.354 true 0.875,2.75 1.146,2.75 1.146,2.75 1.75,3.073 false 0.875,0.604 1.146,0.604 1.146,0.604 1.75,0.927 false 1.083,1.875 1.292,1.875 1.292,1.875 1.677,1.177 true 1.854,1.302 2.156,1.542 0.302,0.24 10 false *a 0.906,1.781 1.219,1.938 0.313,0.156 10 false *b 0.948,3.958 1.24,4.188 0.292,0.229 10 false *b 0.708,0.5 0.958,0.74 0.25,0.24 10 false *c 0.708,2.646 0.958,2.885 0.25,0.24 10 false *c
*a Pull Out
*b Lock Piece
*c Adjuster Case


Using a precision screwdriver, pull out the lock piece of the adjuster case.


h.
C400818C01
0.448,1.208 0.625,1.208 0.625,1.208 1.729,1.49 true 2.188,1.26 2.896,2.208 2.896,2.208 2.208,3.479 true 0.49,3.177 0.708,3.177 0.708,3.177 1.385,3.438 true 0.26,1.115 0.573,1.271 0.313,0.156 10 false *a 2.01,0.365 2.323,0.521 0.313,0.156 10 false *b 2.948,2.104 3.26,2.26 0.313,0.156 10 false *c 0.281,3.104 0.594,3.26 0.313,0.156 10 false *a
*a Lock Nut
*b Push in
*c Stopper


Turn the lock nut of the transmission control cable assembly counterclockwise. While holding the lock nut, push in the stopper.


i.
C453914C02
0.552,0.24 0.75,0.24 0.75,0.24 0.927,0.521 true 2.146,0.188 2.344,0.188 2.344,0.188 2.646,0.427 true 0.354,0.156 0.667,0.313 0.313,0.156 10 false *a 1.927,0.094 2.24,0.25 0.313,0.156 10 false *a
*a Stopper


Connect the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

After installation, check that the outer part of the stopper is as shown in the illustration.

·

Do not forcibly pull the transmission control cable assembly into the cabin.




j.
C453915

Connect the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Before connecting the transmission control cable assembly, check that the shift lever is in N.


·

Securely connect the end of the transmission control cable assembly to the transmission floor shift assembly.




k.
C453916C01
0.885,0.594 1.083,0.594 1.083,0.594 1.438,1.188 true 2.188,1.76 2.031,1.76 2.031,1.76 1.719,1.24 true 1.51,1.469 1.719,1.677 0.208,0.208 10 true *a 2.208,1.656 2.448,1.854 0.24,0.198 10 true *b 0.677,0.49 0.865,0.688 0.188,0.198 10 true *c
*a Push in
*b Lock Piece
*c Adjuster Case


Push in the lock piece of the adjuster case to lock it.

NOTICE:
·
C453917C01
0.406,2.073 0.563,2.073 0.563,2.073 0.74,2.594 true 2.115,0.542 2.458,0.542 false 0.198,1.958 0.385,2.156 0.188,0.198 10 true *1 1.979,0.438 2.219,0.667 0.24,0.229 10 false *a
*1 Transmission Control Cable Assembly
*a Lever Shaft


When pushing in the lock piece of the adjuster case to lock it, remove your hand from the lever shaft.

·

When pushing in the lock piece of the adjuster case to lock it, do not move the lever shaft or transmission control cable assembly forward or backward.




l.
C453918C01
1.156,1.698 1.333,1.698 1.333,1.698 1.656,1.25 true 1.469,4.375 1.646,4.375 1.646,4.375 1.823,3.677 true 0.938,4.25 1.115,4.25 1.115,4.25 1.625,3.667 true 0.938,1.604 1.135,1.802 0.198,0.198 10 true *a 0.74,4.146 0.917,4.344 0.177,0.198 10 true *a 1.26,4.281 1.448,4.479 0.188,0.198 10 true *b
*a Adjuster Case Cover
*b Lock Piece


Move the adjuster case cover in the direction shown by the arrow.

NOTICE:

If the adjuster case cover is not moved far enough so that the adjuster case cover engages the lock piece, the transmission control cable assembly will not be able to lock, and reliable shift operation will not be possible.



Hide 58861B 2.INSTALL NO. 1 CONSOLE BOX DUCT

a.

Install the No. 1 console box duct.


Hide 3.INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY

Hide 58152A 4.INSTALL FRONT LOWER NO. 1 FLOOR HEAT INSULATOR

a.

Install the front lower No. 1 floor heat insulator to the vehicle body with the 2 nuts.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


Hide 17410 5.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 6.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 17750A 7.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 12601B 8.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 53295E 9.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 10.INSPECT SHIFT LEVER POSITION

Hide 11.ADJUST SHIFT LEVER POSITION