Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column) › from 2021.02
RM33A0E _55 Steering _065371 STEERING COLUMN _0327257 STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)  INSTALLATION  


PROCEDURE

Hide 1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45250 2.INSTALL STEERING COLUMN ASSEMBLY

NOTICE:

Make sure that the wire harness is not interfering with the steering column assembly.


a.

Install the steering column assembly with the bolt and 2 nuts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


b.

Connect each connector and engage each wire harness clamp to the steering column assembly.


Hide 45220 3.INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C384401C01
0.615,0.469 1.625,0.469 true 0.917,0.469 0.917,0.542 0.917,0.542 1.604,0.542 true 0.448,0.385 0.604,0.552 0.156,0.167 10 true *a
*a Matchmark


Align the matchmarks on the steering intermediate shaft assembly and steering column assembly.


b.

Install the steering intermediate shaft assembly to the steering column assembly.


c.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


d.
C375250

Tighten the clamp.


Hide 45253 4.INSTALL STEERING COLUMN HOLE COVER

a.

Install the steering column hole cover with the 2 clips.


b.

Install the clip.


c.

Return the floor carpet.


Hide 45220 5.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 6.INSTALL FRONT WHEEL LH

Hide 87211 7.INSTALL NO. 1 AIR DUCT

a.
C373452

Engage the 3 claws to install a new No. 1 air duct.


b.

Install the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 73900 8.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55302D 9.INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY

Hide 55434B 10.INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL

Hide 55435B 11.INSTALL NO. 1 METER HOOD CLUSTER

Hide 53601 12.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 55436B 13.INSTALL NO. 2 METER HOOD CLUSTER

Hide 55606 14.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 62312B 16.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

a.

Install the front door opening trim weatherstrip.

NOTICE:

After installation, check that the corners fit correctly.



Hide 62112A 17.INSTALL COWL SIDE TRIM SUB-ASSEMBLY

Hide 67914 18.INSTALL FRONT DOOR SCUFF PLATE

Hide 19.INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not remove/install the spiral cable with sensor sub-assembly with the battery connected and the engine switch on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the engine switch on (IG).

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.



a.
C375251C01
1.146,0.542 1.427,0.542 false 0.99,0.448 1.302,0.604 0.313,0.156 10 false *a
*a Clamp


Using pliers, expand the clamp.


b.

While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.


c.

Return the clamp to its original position.


d.

Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.


Hide 45286B 20.INSTALL UPPER STEERING COLUMN COVER

a.
C379359

Engage the 2 claws and 4 clips to connect the upper steering column cover.


b.
C384404C01
0,0 0,0 false
V113147

Install in this direction


Engage the claw to install the upper steering column cover.


Hide 45024 21.INSTALL LOWER STEERING COLUMN COVER SUB-ASSEMBLY

a.
C384405

Engage the 2 claws to install the lower steering column cover sub-assembly.


b.
C379356

Install the 3 screws.


Hide 22.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 84306 23.INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Hide 24.INSTALL STEERING WHEEL ASSEMBLY

Hide 25.CHECK STEERING WHEEL CENTER POINT

Hide 45130 26.INSTALL HORN BUTTON ASSEMBLY

Hide 27. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

a.

Set the auto tilt away function setting to the previous condition by changing the customize parameter.

Click hereSteering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>CUSTOMIZE PARAMETERS


Hide 28.PERFORM INITIALIZATION

Parking Assist Monitor System for Initialization:(Click here)
for Calibration:(Click here)
Panoramic View Monitor System for Initialization:(Click here)
for Calibration:(Click here)