Home › Drivetrain › UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE ASSEMBLY › from 2021.02
RM33A0E _52 Drivetrain _065352 UB80E AUTOMATIC TRANSMISSION / TRANSAXLE _0326593 AUTOMATIC TRANSAXLE ASSEMBLY A

UB80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during automatic transaxle assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

*2: w/ Smart Entry and Start System

*3: w/o Smart Entry and Start System

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)w/ Canister Pump Module
(Click here)w/o Canister Pump Module
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)w/ Canister Pump Module
(Click here)w/o Canister Pump Module
Replacement of automatic transaxle assembly
1.

Reset memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)for UB80E Initialization
(Click here)for UB80E Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM*2 Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method
Replacement of ECM*3 Perform code registration (Immobiliser system)
·

Wireless Door Lock Control System

·

Engine start


See Service Bulletin for the registration method
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic view monitor system (Click here)for Initialization
(Click here)for Calibration
Front wheel alignment adjustment
·

Perform "Reset Memory"

·

Perform acceleration sensor zero point calibration and system information memorization


·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)

CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Transmission Jack


The automatic transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop.



PROCEDURE

Hide 1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 11361J 2.REMOVE FLYWHEEL HOUSING UNDER COVER

Hide 32101A 3.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
C374383

Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black colored drive plate and torque converter assembly setting bolt.



Hide 4.DISCONNECT VACUUM HOSE

a.
C374384

Disconnect the vacuum hose from the rear engine mounting insulator.


b.
C374385

Disconnect the vacuum hose from the vacuum hose connector.


c.

Disengage the 9 clamps to disconnect the vacuum hose from the automatic transaxle assembly.

C374386


Hide 16261G 5.REMOVE FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE)

Hide 16260 6.DISCONNECT WATER BY-PASS HOSE ASSEMBLY

a.
A402662

Slide the clip and disconnect the water by-pass hose assembly from the transmission oil cooler.

HINT:

Use a container to catch any coolant which flows out of the water by-pass hose assembly and transmission oil cooler.



Hide 35104V 7.REMOVE BREATHER PLUG HOSE

a.
C374387

Disengage the 2 hose clamps to disconnect the breather plug hose.


b.

Using a screwdriver with its tip wrapped with protective tape, remove the breather plug hose from the No. 1 breather plug (ATM).

NOTICE:

Be careful not to damage the No. 1 breather plug (ATM).



c.
C364011C01
1.688,0.438 2.24,0.438 false 1.167,1.396 1.719,1.396 false 1.531,0.375 1.844,0.531 0.313,0.156 10 false *1 1,1.323 1.313,1.479 0.313,0.156 10 false *2
*1 Breather Plug Sub-assembly
*2 Breather Plug Hose


Remove the breather plug sub-assembly from the breather plug hose.

NOTICE:

Be careful not to damage the breather plug sub-assembly.



Hide 45319 8.REMOVE STEERING GEAR HEAT INSULATOR (for LHD)

Hide 9.DISCONNECT WIRE HARNESS

a.
C374388

Disengage the claw, rotate the lever and disconnect the transmission wire connector.


b.
C374389

Disconnect the park/neutral position switch assembly connector.


c.
C378068

Disengage the wire harness clamp and disconnect the vacuum switching valve (for active control engine mount system) connector.


d.

for LHD:

i.

Disconnect the rack and pinion power steering gear assembly connector.

C374274

HINT:

Release the lock before rotating the lock lever.



ii.

Remove the 2 bolts to disconnect the wire harness from the rack and pinion power steering gear assembly.


iii.

Remove the bolt.

C374390


iv.

Disengage the 9 wire harness clamps to disconnect the wire harness.



e.

for RHD:

i.

Disconnect the rack and pinion power steering gear assembly connector.

C402162

HINT:

Release the lock before rotating the lock lever.



ii.

Remove the bolt to disconnect the wire harness from the rack and pinion power steering gear assembly.


iii.

Remove the bolt.

C402163


iv.

Disengage the 8 wire harness clamps to disconnect the wire harness.



f.
C374391

Remove the 2 bolts.


g.

Disengage the wire harness clamp to disconnect the wire harness from the automatic transaxle assembly.


Hide 51100G 12.REMOVE FRONT FRAME ASSEMBLY

Hide 12311A 13.REMOVE FRONT ENGINE MOUNTING BRACKET

a.
C374392

Remove the 3 bolts and front engine mounting bracket from the transaxle housing.


Hide 11363A 14.REMOVE FLYWHEEL HOUSING SIDE COVER (for DENSO Made)

Hide 11363A 15.REMOVE FLYWHEEL HOUSING SIDE COVER (for VALEO Made)

Hide 28100 16.REMOVE STARTER ASSEMBLY (for DENSO Made)

a.
C428718

Disconnect the starter assembly connector.


b.

Open the terminal cap.


c.
C428719

Remove the nut and disconnect the No. 2 engine wire from terminal 30.


d.
C428720

Remove the 2 bolts and starter assembly from the cylinder block sub-assembly.


Hide 28100 17.REMOVE STARTER ASSEMBLY (for VALEO Made)

Hide 30500 18.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY

a.

Support the automatic transaxle assembly with a transmission jack.

NOTICE:

Secure the automatic transaxle assembly to the transmission jack using a suitable adapter, such as a rope or attachment.



b.
C374393

Remove the 8 bolts and automatic transaxle assembly.

NOTICE:

To prevent damage to the knock pins, do not pry between the automatic transaxle assembly and engine assembly.



Hide 12372A 19.REMOVE ENGINE MOUNTING INSULATOR LH

a.
C374394

Remove the 5 bolts and engine mounting insulator LH from the automatic transaxle case sub-assembly.


Hide 12303 21.REMOVE REAR ENGINE MOUNTING BRACKET SUB-ASSEMBLY

a.
C374395

Remove the 4 bolts and rear engine mounting bracket sub-assembly from the transaxle housing.


Hide 32942 22.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE (w/o Air Cooled Oil Cooler)

Hide 32941 23.DISCONNECT INLET NO. 1 OIL COOLER HOSE

Hide 32907C 24.REMOVE NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE

a.
C454119C01
0.052,0.052 0.344,0.292 0.292,0.24 12 false *A 0.052,2.385 0.344,2.625 0.292,0.24 12 false *B
*A w/o Air Cooled Oil Cooler
*B w/ Air Cooled Oil Cooler


Remove the 2 bolts to disconnect the No. 1 oil cooler tube sub-assembly without hose from the automatic transaxle case sub-assembly.


b.
C378430

Slide the clip and disconnect the inlet No. 2 oil cooler hose from the transmission oil cooler.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 2 oil cooler hose and transmission oil cooler.



c.
C378431

Slide the clip and disconnect the outlet No. 2 oil cooler hose to remove the No. 1 oil cooler tube sub-assembly without hose from the transmission oil cooler.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the outlet No. 2 oil cooler hose and transmission oil cooler.



Hide 33493A 25.REMOVE TRANSMISSION OIL COOLER

Hide 33823 26.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C374396

Remove the 2 bolts and No. 1 transmission control cable bracket from the automatic transaxle case sub-assembly.


Hide 35150 27.REMOVE TRANSMISSION CASE PLUG ASSEMBLY

a.
C378105

Remove the transmission case plug assembly from the transaxle housing.


b.

Remove the O-ring from the transmission case plug assembly.


Hide 28.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C374398

Remove the bolt and wire harness clamp bracket from the automatic transaxle case sub-assembly.


b.
C374399

Remove the bolt and wire harness clamp bracket from the automatic transaxle case sub-assembly.


c.
C374400

Remove the 4 bolts and 4 wire harness clamp brackets from the automatic transaxle case sub-assembly and transmission case side cover.


Hide 32000 29.REMOVE TORQUE CONVERTER ASSEMBLY

a.

Remove the torque converter assembly from the automatic transaxle assembly.


Hide 32101 31.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY