Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for RHD) › from 2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0319138 BRAKE ACTUATOR(for RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for RHD)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

The parking brake indicator light blinks (red) when the ignition switch is turned to ON after replacing the brake actuator assembly. Operate the electric parking brake switch assembly to turn off the parking brake indicator light.


PROCEDURE

Hide 44547B 1.INSTALL BRAKE ACTUATOR BRACKET CUSHION

HINT:

Perform this procedure only when replacement of the brake actuator bracket cushions is necessary.


a.

Install the 3 brake actuator bracket cushions to the brake actuator bracket assembly.


Hide 44521B 2.INSTALL NO. 2 BRAKE ACTUATOR CASE COLLAR

HINT:

Perform this procedure only when replacement of the No. 2 brake actuator case collars is necessary.


a.

Install the 3 No. 2 brake actuator case collars to the brake actuator bracket cushion.

NOTICE:

Make sure that the No. 2 brake actuator case collar is in full contact with the brake actuator bracket cushion.



b.

Install the 3 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 44510 3.INSTALL BRAKE ACTUATOR ASSEMBLY

a.
C448619N01
0.656,1.104 0.813,1.302 0.156,0.198 10 true 1 0.26,0.854 0.417,1.052 0.156,0.198 10 true 2 2.531,1.563 2.688,1.74 0.156,0.177 10 true 3

Temporarily install the brake actuator assembly to the brake actuator bracket assembly with the 3 bolts.


b.

Tighten the 3 bolts in the order shown in the illustration.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake tubes because the brake actuator assembly is filled with brake fluid.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 4.INSTALL BRAKE ACTUATOR WITH BRACKET

a.
C448618N01
1.177,1.958 1.302,2.146 0.125,0.188 10 true 1 1.583,0.031 1.708,0.219 0.125,0.188 10 true 2 1.594,1.979 1.719,2.167 0.125,0.188 10 true 3

Temporarily install the brake actuator with bracket to the vehicle body with the 2 bolts and nut.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Install the brake actuator with bracket while avoiding the brake lines.



b.

Fully tighten the 2 bolts and nut in the order shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.

Remove the protective tape.


d.
C448616

Engage the clamp to install a new brake tube clamp.


e.

Return the front No. 5 brake tube to its original position.

NOTICE:

Do not apply excessive force to the front No. 5 brake tube.



f.
C376034

Temporarily install the front No. 5 brake tube to the front flexible hose.

NOTICE:
·

Do not kink or damage the front No. 5 brake tube.

·

Do not allow any foreign matter such as dirt or dust to enter the front No. 5 brake tube from the connecting parts.




g.
C448614

Engage the clamp to connect the front No. 5 brake tube.

NOTICE:

Do not kink or damage the front No. 5 brake tube.



h.
C449068C01
1.323,0.958 1.615,0.958 true 2.729,0.25 2.313,0.25 2.313,0.25 2,0.583 true 2.146,0.656 2.729,0.656 true 1.823,1.406 1.823,0.906 true 2.75,0.563 2.948,0.729 0.198,0.167 10 true *a 2.75,0.167 2.938,0.333 0.188,0.167 10 true *b 1.74,1.427 1.917,1.604 0.177,0.177 10 true *c 1.125,0.875 1.313,1.042 0.188,0.167 10 true *d
*a To Front Wheel Cylinder Assembly RH
*b To Rear Wheel Cylinder Assembly LH
*c To Rear Wheel Cylinder Assembly RH
*d To Front Wheel Cylinder Assembly LH


Temporarily tighten the 4 brake lines to the correct positions on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




i.
C449191C01
2.896,2.927 2.729,2.927 2.729,2.927 2.729,2.677 false 1.76,2.938 2.073,3.094 0.313,0.156 10 false *a 2.917,2.844 3.229,3 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten each brake line.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the brake lines.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




j.
C449192C01
1.281,0.708 1.781,0.708 1.781,0.708 2.115,0.958 true 1.302,1.177 1.844,1.177 true 1.083,0.615 1.26,0.802 0.177,0.188 10 true *a 1.094,1.094 1.281,1.26 0.188,0.167 10 true *b
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly


Temporarily tighten the 2 brake lines to the correct positions on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




k.
C451182C01
2.906,2.917 2.708,2.917 2.708,2.917 2.708,2.656 false 1.792,2.948 2.104,3.104 0.313,0.156 10 false *a 2.938,2.844 3.25,3 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten each brake line.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:

Do not kink or damage the brake lines.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

17.4 N*m (177 kgf*cm, 13 ft.*lbf)




l.
C376035C01
2.906,2.896 2.719,2.896 2.719,2.896 2.719,2.656 false 1.802,2.938 2.115,3.094 0.313,0.156 10 false *a 2.927,2.813 3.24,2.969 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten the front No. 5 brake tube while holding the front flexible hose with a wrench.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the front No. 5 brake tube.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




m.
C454612C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake actuator assembly and lock the lock lever.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the actuator connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter the connector.




Hide 74404A 5.INSTALL BATTERY CLAMP SUB-ASSEMBLY

a.
C373428

Install the battery clamp sub-assembly with the 3 bolts and nut.

Torque:
Bolt : 18.5 N*m (189 kgf*cm, 14 ft.*lbf)
Nut : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Engage the 4 clamps to the battery clamp sub-assembly.


Hide 6.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 12601B 7.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 8.INSTALL FRONT WHEEL LH

Hide 28800 9.INSTALL BATTERY

Hide 10.BLEED BRAKE SYSTEM

Hide 53607A 11.INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY

a.
C377997N02
1,1.927 1.115,2.083 0.115,0.156 10 true A 2.448,1.927 2.552,2.073 0.104,0.146 10 true A 2.833,1.917 2.938,2.063 0.104,0.146 10 true B 0.594,1.917 0.708,2.063 0.115,0.146 10 true B

Temporarily install the front center upper suspension brace sub-assembly with the 6 bolts and 4 nuts.


b.

Fully tighten the 2 nuts (A).

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


c.

Fully tighten the 6 bolts and 2 nuts (B) to install the front center upper suspension brace sub-assembly.

Torque:
Bolt : 8.9 N*m (91 kgf*cm, 79 in.*lbf)
Nut (B) : 39 N*m (398 kgf*cm, 29 ft.*lbf)


d.

Engage the 3 clamps to install the wire harness.


e.

Connect the connector.


Hide 55708 12.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 13. PERFORM SYSTEM VARIANT LEARNING AND ACCELERATION SENSOR ZERO POINT CALIBRATION