Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for LHD) › from 2021.02
RM33A0E _54 Brake _065366 BRAKE SYSTEM (OTHER) _0319131 BRAKE PEDAL(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for LHD)  INSTALLATION  


PROCEDURE

Hide 47121 1.INSTALL BRAKE PEDAL PAD

a.

Install the brake pedal pad to the brake pedal support assembly.


Hide 84345 2.INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER

a.

Engage the 2 claws to install the stop light switch mounting adjuster.


Hide 47101A 3.INSTALL BRAKE PEDAL RETURN SPRING

a.
C372724

Install the brake pedal return spring to the brake pedal support assembly.

NOTICE:

Attach the bottom part of the brake pedal return spring first, making sure that the open part of the hook is facing the front of the vehicle. Attach the top part of the brake pedal return spring second, making sure that the open part of the hook is facing the rear of the vehicle.



Hide 4.INSTALL BRAKE PEDAL SUPPORT ASSEMBLY

a.

Push the brake booster assembly toward the engine compartment, and install the brake pedal support assembly while avoiding the stud bolts of the brake booster assembly and brake booster support base.

NOTICE:
·

Be careful not to deform the bracket of the instrument panel reinforcement assembly.

·

Do not apply excessive force to the brake lines.

·

Do not apply excessive force to the wire harness.




b.

Return the brake booster assembly to its original position.


c.
C372723C02
0,0 0,0 false
V100135

Nut
V100136

Clip


Temporarily install the brake pedal support assembly with 2 new clips.


d.

Install the 4 nuts.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


e.

Install the brake pedal support assembly to the instrument panel reinforcement assembly with the bolt.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


f.

Engage the clamp to install the wire harness to the brake pedal support assembly.


Hide 47264A 5.INSTALL PUSH ROD PIN

a.
C319792C01
0,0 0,0 false
V100144

Lithium Soap Base Glycol Grease


Apply lithium soap base glycol grease to the push rod pin.


b.
C372720

Connect the brake master cylinder push rod clevis to the brake pedal support assembly with the push rod pin, and install a new clip as shown in the illustration.

HINT:

The push rod pin can be installed in either direction.



Hide 84340 6.INSTALL STOP LIGHT SWITCH ASSEMBLY

Hide 55606 7.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 8.CONNECT BRAKE LINE

a.
C454621C01
2.906,2.885 2.719,2.885 2.719,2.885 2.719,2.646 false 1.792,2.938 2.104,3.094 0.313,0.156 10 false *a 2.938,2.813 3.25,2.969 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, connect the 2 brake lines to the brake master cylinder sub-assembly.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

17.4 N*m (177 kgf*cm, 13 ft.*lbf)




Hide 9.BLEED BRAKE SYSTEM

Hide 28800 10.INSTALL BATTERY

Hide 11.INSPECT AND ADJUST BRAKE PEDAL