Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for LHD) › 2021.02–2021.08
RM33A0E _54 Brake _065366 BRAKE SYSTEM (OTHER) _0319131 BRAKE PEDAL(for LHD) N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for LHD)  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

a.

Remove the front door scuff plate LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


b.

Remove the cowl side trim sub-assembly LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


c.

Remove the No. 1 instrument panel under cover sub-assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL




f.

Check the brake pedal height.

HINT:

Inspect and adjust the brake pedal height with the floor carpet and front floor mat folded back.


i.

Measure the shortest distance between the brake pedal pad surface and floor panel as shown in the illustration.

C372725C01
5.01,2.865 5.26,2.865 5.26,2.865 5.552,2.51 true 2.135,2.406 2.135,2.083 true 6.073,1.646 6.281,1.354 6.281,1.354 6.573,1.354 false 2.458,2.979 2.458,2.656 true 2.063,2.417 2.24,2.583 0.177,0.167 10 true *1 2.677,2.156 2.865,2.333 0.188,0.177 10 true *a 4.854,2.792 5.167,2.948 0.313,0.156 10 false *b 1.135,1.635 1.323,1.813 0.188,0.177 10 true *c 6.604,1.271 6.813,1.438 0.208,0.167 10 false *1 6.177,2.302 6.49,2.458 0.313,0.156 10 false *a 2.396,2.99 2.573,3.156 0.177,0.167 10 true *b
*1 Brake Pedal Pad - -
*a Brake Pedal Height *b Measuring Plane of Floor Panel
*c 36 mm (1.42 in.) - -


Brake Pedal Height from Floor Panel:

149.5 to 159.5 mm (5.89 to 6.28 in.)


If the brake pedal height is not as specified, inspect and adjust the push rod length according to the procedure below.



g.

Adjust the push rod length.

i.
C373411C01
2.104,1.646 2.104,0.896 2.104,0.896 2.354,0.896 false 1.708,4.125 2.01,4.125 2.01,4.125 2.302,3.781 true 2.802,1.729 2.802,1.448 2.802,1.448 3.021,1.448 false 2.385,0.823 2.698,0.979 0.313,0.156 10 false *1 3.052,1.375 3.365,1.531 0.313,0.156 10 false *2 1.552,4.063 1.865,4.219 0.313,0.156 10 false *a 2.917,3.656 3.229,3.813 0.313,0.156 10 false *b
*1 Lock Nut
*2 Stop Light Switch Assembly
*a Floor Panel
*b Brake Pedal Height


Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


ii.

Loosen the lock nut.


iii.

Adjust the brake pedal height by turning the push rod.

Brake Pedal Height from Floor Panel:

149.5 to 159.5 mm (5.89 to 6.28 in.)



iv.

Tighten the lock nut.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


v.

Install the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION





j.

Install the No. 1 instrument panel under cover sub-assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION


k.

Install the cowl side trim sub-assembly LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


l.

Install the front door scuff plate LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 2.INSPECT BRAKE PEDAL FREE PLAY

a.

Stop the engine and firmly depress the brake pedal several times until no vacuum is left in the brake booster assembly.


b.
C132708C09
2.167,1.563 2.469,1.781 0.302,0.219 10 false *a
*a Brake Pedal Free Play


Depress the brake pedal until a slight resistance is felt. Measure the distance as shown in the illustration.

Brake Pedal Free Play:

1.0 to 6.0 mm (0.0394 to 0.236 in.)


If the brake pedal free play is not as specified, check the stop light switch clearance.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

If the brake pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.


Hide 3.INSPECT BRAKE PEDAL RESERVE DISTANCE

HINT:

Measure the distance at the same point used for the brake pedal height inspection.


a.

With the engine running, depress the brake pedal and measure the brake pedal reserve distance as shown in the illustration.

C372726C01
5.01,2.917 5.313,2.917 5.313,2.917 5.573,2.5 true 2.104,2.49 2.104,2.135 true 5.729,1.75 5.938,1.5 5.938,1.5 6.188,1.5 false 2.417,3.021 2.417,2.667 true 2.031,2.49 2.208,2.656 0.177,0.167 10 true *1 2.667,2.177 2.844,2.354 0.177,0.177 10 true *a 2.354,3.031 2.531,3.198 0.177,0.167 10 true *b 1.063,1.688 1.24,1.865 0.177,0.177 10 true *c 6.219,1.427 6.531,1.583 0.313,0.156 10 false *1 6.073,2.427 6.385,2.583 0.313,0.156 10 false *a 4.865,2.854 5.177,3.01 0.313,0.156 10 false *b
*1 Brake Pedal Pad - -
*a Brake Pedal Reserve Distance *b Measuring Plane of Floor Panel
*c 36 mm (1.42 in.) - -


Brake Pedal Reserve Distance from Floor Panel at 300 N (31 kgf, 67.4 lbf):
Front Brake Specification
for 16 inch Front Disc Brake 81 mm (3.19 in.) or more
for 17 inch Front Disc Brake 79 mm (3.11 in.) or more


If the distance is not as specified, troubleshoot the brake system.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE