Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for LHD) › from 2021.02
RM33A0E _54 Brake _065366 BRAKE SYSTEM (OTHER) _0319133 BRAKE BOOSTER(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake booster assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)

CAUTION / NOTICE / HINT

NOTICE:

Make sure to release vacuum from the brake booster assembly before removing the brake master cylinder sub-assembly from the brake booster assembly.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY

Hide 55606 3.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55708 4.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53607A 5.REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY

Hide 12601B 6.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (for A25A-FKS)

Hide 7.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE (for A25A-FKS)

Hide 8.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE (for 2GR-FKS)

Hide 12601B 9.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (for M20A-FKS)

Hide 10.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE (for M20A-FKS)

Hide 74404A 11.REMOVE BATTERY CLAMP SUB-ASSEMBLY

a.
C373428

for A25A-FKS, M20A-FKS:

i.

Disengage the 4 clamps from the battery clamp sub-assembly.


ii.

Remove the 3 bolts, nut and battery clamp sub-assembly.



b.

for 2GR-FKS:

i.
C380324

Disengage the 5 clamps from the battery clamp sub-assembly.


ii.

Remove the 3 bolts, nut and battery clamp sub-assembly.



Hide 44773F 12.DISCONNECT UNION TO CHECK VALVE HOSE

a.
C454624

Slide the clip and disconnect the union to check valve hose from the brake booster assembly.


Hide 13.LOOSEN LOCK NUT

a.
C372741C01
1.615,0.969 1.615,0.552 1.615,0.552 1.896,0.552 false 2.208,1.635 2.021,1.635 2.021,1.635 1.844,1.115 true 1.927,0.469 2.24,0.625 0.313,0.156 10 false *1 2.229,1.552 2.417,1.729 0.188,0.177 10 true *2
*1 Lock Nut
*2 Brake Master Cylinder Push Rod Clevis


Loosen the lock nut of the brake master cylinder push rod clevis.


Hide 47264A 14.REMOVE PUSH ROD PIN

Hide 44610 15.REMOVE BRAKE BOOSTER ASSEMBLY

a.
C454625

Disconnect the connector from the vacuum warning switch assembly.


b.
C372742

Remove the 4 nuts and push the brake booster assembly toward the engine compartment.

NOTICE:

Do not apply excessive force to the brake lines.



c.

Remove the brake master cylinder push rod clevis and lock nut from the brake booster assembly.


d.

Remove the brake booster assembly from the vehicle body.

NOTICE:

Do not apply excessive force to the brake lines.



Hide 44785 16.REMOVE BRAKE BOOSTER GASKET