Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2021.02
RM33A0E _51 Engine / Hybrid System _065333 2GR-FKS ENGINE MECHANICAL _0327370 ENGINE ASSEMBLY A

2GR-FKS ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision system
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly
1.

Reset Memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for Initialization
(Click here)
for Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
for Initialization
(Click here)
for Calibration
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic view monitor system (Click here)
for Initialization
(Click here)
for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (Click here)
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front wheel alignment adjustment
·

Perform "Reset Memory"

·

Perform acceleration sensor zero point calibration and system information memorization


·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 5.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 6. SECURE STEERING WHEEL

Hide 53852K 7.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

a.

Remove the 3 screws and front wheel opening extension pad LH.


Hide 53851M 8.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

a.

Remove the 3 screws and front wheel opening extension pad RH.


Hide 51441 9.REMOVE NO. 1 ENGINE UNDER COVER

a.

Remove the bolt, 2 clips, 6 screws and No. 1 engine under cover.


Hide 53737B 10.REMOVE FRONT FENDER APRON SEAL LH

a.

Remove the 2 screws, clip and front fender apron seal LH from the vehicle body.


Hide 53736 11.REMOVE FRONT FENDER APRON SEAL RH

a.

Remove the 2 screws, clip and front fender apron seal RH from the vehicle body.


Hide 52119A 12.REMOVE FRONT BUMPER COVER

Hide 52618 13.REMOVE FRONT LOWER BUMPER ABSORBER

a.
A410496

Remove the 4 bolts.


b.

Disengage the 2 claws to remove the front lower bumper absorber.


Hide 14.DRAIN ENGINE COOLANT

Hide 11209 17.REMOVE V-BANK COVER SUB-ASSEMBLY

a.

Disengage the 4 clips in the order shown in the illustration and lift the V-bank cover sub-assembly upward to remove it.

A408702C01
4.219,1.646 4.375,1.844 0.156,0.198 10 true 1 2.573,1.802 2.729,2 0.156,0.198 10 true 2 3.344,1.01 3.5,1.208 0.156,0.198 10 true 3 4.146,1.031 4.302,1.229 0.156,0.198 10 true 4
V113146

Hold here
V113147

Pull in this Direction


NOTICE:
·

Pull the V-bank cover sub-assembly straight up to remove it.

·

Do not remove the V-bank cover sub-assembly in any direction other than upward. If the V-bank cover sub-assembly is removed in any direction other than upward, it may be damaged.

·

If the clips are not disengaged in the order shown in the illustration, the V-bank cover sub-assembly may be damaged.




Hide 17750A 18.REMOVE INLET AIR CLEANER ASSEMBLY

a.
A399875

Remove the 2 bolts and inlet air cleaner assembly.


Hide 19.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

a.
A408243C01
2.219,0.844 2.729,0.844 true 1.063,1.135 1.573,1.135 true 2.75,0.76 3.063,0.958 0.313,0.198 10 true *1 0.75,1.021 1.063,1.219 0.313,0.198 10 true *2
*1 No. 1 Fuel Vapor Feed Hose
*2 No. 2 Ventilation Hose


Disengage the 2 clamps to disconnect the No. 1 fuel vapor feed hose from the air cleaner hose.


b.

Slide the clip and disconnect the No. 2 ventilation hose from the air cleaner hose.


c.
A408244

Loosen the hose clamp.


d.
A408242C01
1.448,3.313 1.854,3.969 true 1.854,3.99 1.802,3.521 true 0.927,3.99 0.594,4.156 true 1.813,4.031 2.125,4.229 0.313,0.198 10 false *a 0.406,4.104 0.719,4.302 0.313,0.198 10 false *a
*a Pin


Disconnect the mass air flow meter sub-assembly connector.


e.

Disengage the 3 wire harness clamps.


f.

Disconnect the vacuum hose from the air cleaner hose.


g.

Disengage the 3 pins and remove the air cleaner assembly with air cleaner hose.

NOTICE:

Make sure the air cleaner support remains attached to the vehicle body.



Hide 82111 21.DISCONNECT ENGINE ROOM MAIN WIRE

a.
A407936

Remove the nut and disconnect the engine wire with engine room main wire from the positive (+) battery terminal.


Hide 22.REMOVE BATTERY

Hide 74404A 23.REMOVE BATTERY CLAMP SUB-ASSEMBLY

a.
A399873

Disengage the 5 clamps from the battery clamp sub-assembly.


b.

Remove the 3 bolts and battery clamp sub-assembly.


Hide 33820B 24.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C374454C01
1.677,2.344 1.917,2 1.917,2 2.083,2 false 2.115,1.875 2.438,2.083 0.323,0.208 10 false *a 2.969,3.146 3.229,3.365 0.26,0.219 10 false *b
*a Clip
*b 45° to 60°


While disengaging the clip as shown in the illustration, disconnect the transmission control cable assembly from the transmission control shaft lever together with the clip.


b.
C378070

Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.


Hide 23826 25.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A399864

Slide the clip and disconnect the No. 1 fuel vapor feed hose from the No. 1 vacuum switching valve assembly.


Hide 44773F 26.DISCONNECT UNION TO CHECK VALVE HOSE

a.
A399865

Slide the clip and disconnect the union to check valve hose from the brake booster assembly.


Hide 16572D 27.DISCONNECT NO. 2 RADIATOR HOSE

a.
A399858

Slide the clip and disconnect the No. 2 radiator hose from the water inlet.


Hide 28.SEPARATE RADIATOR HOSE SUB-ASSEMBLY

a.
A399859

Slide the clip and disconnect the radiator hose sub-assembly from the water outlet.


b.

Remove the 2 bolts and separate the radiator hose sub-assembly from the engine assembly.


Hide 87245 29.DISCONNECT INLET HEATER WATER HOSE

a.
A399860

Disengage the clamp.


b.

Slide the clip and disconnect the inlet heater water hose from the water outlet.


Hide 87246 30.DISCONNECT OUTLET HEATER WATER HOSE

a.
A399861

Slide the clip and disconnect the outlet heater water hose from the heater water pipe.


Hide 23801F 31.DISCONNECT NO. 1 FUEL HOSE

a.
A405952

Disengage the 2 claws to remove the No. 2 fuel pipe clamp.


b.
A393279

Remove the No. 1 fuel pipe clamp from the fuel tube connector.


c.

Disconnect the No. 1 fuel hose (for Port Injection).

i.
A399867

Disconnect the No. 1 fuel hose from the fuel pipe.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION



d.

Disconnect the No. 1 fuel hose (for Direct Injection).

i.
A399868

Disconnect the No. 1 fuel hose from the fuel pipe.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION



e.
A420747

Separate the bolt and disengage the No. 1 fuel hose.


Hide 88711 32.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY

Hide 88704 33.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 82121 34.DISCONNECT ENGINE WIRE

HINT:

After disconnecting the engine wire, secure it with tape or equivalent to keep it out of the way.


a.
A399862

Remove the No. 2 relay block cover from the engine room relay block and junction block assembly.


b.
A399863

Remove the nut from the engine room relay block and junction block assembly.


c.

Disconnect the 4 connectors from the engine room relay block and junction block assembly.


d.

Disengage the 2 clamps.


e.

Using a screwdriver, disengage the claw and disconnect the engine wire from the engine room relay block and junction block assembly.


f.
A399866

Remove the bolt.


g.

Disengage the 2 clamps and disconnect the engine wire from the vehicle body.


Hide 82284 35.DISCONNECT EARTH WIRE

a.
A407938

Remove the 2 bolts and disconnect the earth wire from the vehicle body.


Hide 45220 36.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 17571 39.REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Upper Side)

a.
A399872

Remove the 2 bolts and No. 1 exhaust pipe support bracket from the oil pan sub-assembly.


Hide 11361J 40.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
A396416

Remove the 2 bolts and flywheel housing under cover.


Hide 32101A 41.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

Hide 42.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set an engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly with transaxle.




b.
A408760

Remove the bolt, 2 nuts and No. 2 engine mounting stay RH.


c.
A399870

Remove the 3 bolts and nut and separate the engine mounting insulator sub-assembly RH from the front No. 1 engine mounting bracket LH.


d.
A399869

Remove the bolt and nut and separate the engine mounting insulator LH from the engine mounting bracket sub-assembly LH.


e.
A399871C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 8 bolts and front bumper extension sub-assembly RH and front bumper extension sub-assembly LH from the front frame assembly and vehicle body.


f.

Remove the 4 bolts, 2 nuts and front suspension member bracket sub-assembly RH and front suspension member bracket sub-assembly LH from the front frame assembly and vehicle body.


g.

Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.




Hide 28100 44.REMOVE STARTER ASSEMBLY

Hide 16260 47.DISCONNECT WATER BY-PASS HOSE ASSEMBLY

Hide 82121 48.REMOVE ENGINE WIRE

a.

Disconnect all clamps and connectors and remove the engine wire from the engine assembly with transaxle.


Hide 49.INSTALL ENGINE HANGERS

a.
A373557C02
1.104,0.729 1.521,0.729 true 2.688,0.719 3.115,0.719 true 0.021,0.021 0.354,0.271 0.333,0.25 12 true *A 1.677,0.031 2,0.26 0.323,0.229 12 true *B 1.583,0.646 1.896,0.802 0.313,0.156 10 false *1 3.156,0.646 3.406,0.865 0.25,0.219 10 false *2
*A for Bank 1
*B for Bank 2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-31121
No. 2 Engine Hanger 12282-31100
Bolt 91671-10825



b.

Using an engine sling device and engine lifter, secure the engine assembly with transaxle.

NOTICE:
·

Adjust the angle of the sling device carefully to prevent damage or deformation to the engine hangers or engine assembly.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




Hide 51100G 50.REMOVE FRONT FRAME ASSEMBLY

a.
A409658

Remove the bolt and separate the front engine mounting insulator from the front engine mounting bracket.


b.
A400014

Remove the 4 nuts and separate the rear engine mounting insulator from the front frame assembly.


Hide 12361A 51.REMOVE FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


a.
A409265

Remove the 3 nuts and front engine mounting insulator from the front frame assembly.


Hide 12371A 52.REMOVE REAR ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ACTIVE CONTROL ENGINE MOUNT (for Rear Side)>REMOVAL

Hide 32101 55.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 19315 56.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 57.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

a.

Install the engine assembly to an engine stand.


Hide 58.REMOVE ENGINE HANGERS

a.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and cylinder head LH.


Hide 12305 59.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A415563

Disengage the clamp.


b.

Remove the bolt, nut and separate the radiator reserve tank assembly.


c.
A399884

Remove the bolt and separate the bracket from the engine mounting insulator sub-assembly RH.


d.
A424802

Remove the bolt and disconnect the No. 1 bond cable from the engine mounting insulator sub-assembly RH.


e.
A401622

Disengage the clamp.


f.

Remove the nut, 2 bolts and engine mounting insulator sub-assembly RH from the engine mounting spacer and vehicle body.


Hide 12341 60.REMOVE ENGINE MOUNTING SPACER

HINT:

Perform this procedure only when replacement of the engine mounting spacer is necessary.


a.
A415554

Remove the 2 bolts and engine mounting spacer from the vehicle body.


Hide 12304 61.REMOVE ENGINE MOUNTING BRACKET SUB-ASSEMBLY LH

HINT:

Perform this procedure only when replacement of the engine mounting bracket sub-assembly LH is necessary.


a.
A415553

Remove the 4 bolts and engine mounting bracket sub-assembly LH from the vehicle body.


Hide 12372A 62.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>REMOVAL