Home › Engine / Hybrid System › M20A-FKS (FUEL) › FUEL MAIN VALVE › from 2021.02
RM33A0E _51 Engine / Hybrid System _098628 M20A-FKS FUEL _0462957 FUEL MAIN VALVE A

M20A-FKS FUEL  FUEL MAIN VALVE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel main valve assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:
A502669C01
0.781,1.385 1.469,1.385 true 0.885,3.833 1.573,3.833 true 0.208,2.396 0.583,2.635 0.375,0.24 12 false *B 0.156,0.156 0.531,0.396 0.375,0.24 12 false *A 0.604,1.281 0.917,1.479 0.313,0.198 10 false *a 0.688,3.74 1,3.938 0.313,0.198 10 false *a
*A for Type A
*B for Type B
*a Tube


·

Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is pressed into the fuel suction plate sub-assembly.

·

When replacing the fuel filter, replace it together with the fuel suction plate sub-assembly.



PROCEDURE

Hide 83320 1.REMOVE FUEL SENDER GAUGE ASSEMBLY

Hide 2.SEPARATE FUEL FILTER (for Type A)

a.
A406593

Disengage the clamp to disconnect the tube from the fuel filter.


b.
A406594C01
0.604,1.417 0.813,1.417 0.813,1.417 1.052,0.833 true 0.417,1.313 0.729,1.469 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disengage the 3 claws.


c.
A406595C01
2.125,1.969 1.833,1.969 1.833,1.969 1.406,1.271 true 2.177,1.896 2.49,2.052 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, separate the fuel filter from the fuel sub-tank.

NOTICE:
·

Do not damage the fuel sub-tank and fuel filter.

·

Pull out the fuel filter carefully because the O-ring is firmly installed between the fuel filter and fuel sub-tank.

·

Do not do anything which may separate the tube from either the fuel suction plate sub-assembly or fuel filter, such as applying excessive force to the tube.

Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION




d.
A401692

Remove the O-ring from the fuel sub-tank.


Hide 23221 3.REMOVE FUEL PUMP (for Type B)

Hide 23070 4.REMOVE FUEL MAIN VALVE ASSEMBLY (for Low Pressure)

a.

for Type A:

i.
A401693

Remove the clip from the fuel filter.


ii.
A401694C01
2.542,1.427 2.333,1.427 2.333,1.427 1.917,0.927 true 2.604,1.344 2.917,1.5 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the fuel main valve assembly from the fuel filter.

NOTICE:
·

Pull out the fuel main valve assembly carefully because the O-rings are firmly installed between the fuel main valve assembly and fuel filter.

·

Do not damage the fuel filter.




iii.
A097616C10
0.875,0.969 0.875,0.5 false 0.667,0.5 1.833,0.5 1.833,0.5 1.833,0.729 false 0.469,0.427 0.75,0.604 0.281,0.177 10 false *1
*1 O-ring


Remove the 2 O-rings from the fuel main valve assembly.



b.
A502661

for Type B:

i.

Remove the clip from the fuel filter.


ii.
A502662C01
1.573,0.865 1.771,0.333 1.771,0.333 1.927,0.333 true 1.958,0.24 2.167,0.417 0.208,0.177 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the fuel main valve assembly from the fuel filter.

NOTICE:
·

Pull out the fuel main valve assembly carefully because the O-rings are firmly installed between the fuel main valve assembly and fuel filter.

·

Do not damage the fuel filter.




iii.
A097616C10
0.875,0.969 0.875,0.5 false 0.667,0.5 1.833,0.5 1.833,0.5 1.833,0.729 false 0.469,0.427 0.75,0.604 0.281,0.177 10 false *1
*1 O-ring


Remove the 2 O-rings from the fuel main valve assembly.



Hide 23070 5.REMOVE FUEL MAIN VALVE ASSEMBLY (for High Pressure)

a.

for Type A:

i.
A401695

Remove the clip from the fuel filter.


ii.
A401696C01
1.24,1.344 1.448,1.344 1.448,1.344 1.698,0.906 true 1.063,1.25 1.25,1.406 0.188,0.156 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the fuel main valve assembly from the fuel filter.

NOTICE:
·

Pull out the fuel main valve assembly carefully because the O-ring is firmly installed between the fuel main valve assembly and fuel filter.

·

Do not damage the fuel filter.




iii.
A401697C02
1.021,0.417 1.125,0.417 1.125,0.417 1.229,0.823 false 1.563,0.688 1.698,0.292 1.698,0.292 1.813,0.292 false 0.958,1.719 1.073,1.719 1.073,1.719 1.135,1.375 false 1.865,0.208 2.177,0.365 0.313,0.156 10 false *1 0.854,0.313 1.167,0.469 0.313,0.156 10 false *a 0.792,1.625 1.104,1.781 0.313,0.156 10 false *b
*1 O-ring
*a Mesh
*b Mini-clip


Remove the O-ring from the fuel main valve assembly.

NOTICE:

Do not remove the mesh and mini-clip from the fuel main valve assembly.




b.
A502663

for Type B:

i.

Remove the clip from the fuel filter.


ii.
A502664C01
2.135,0.865 2.26,0.458 2.26,0.458 2.365,0.458 true 2.417,0.375 2.667,0.563 0.25,0.188 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the fuel main valve assembly from the fuel filter.

NOTICE:
·

Pull out the fuel main valve assembly carefully because the O-rings are firmly installed between the fuel main valve assembly and fuel filter.

·

Do not damage the fuel filter.




iii.
A097616C10
0.875,0.969 0.875,0.5 false 0.667,0.5 1.833,0.5 1.833,0.5 1.833,0.729 false 0.469,0.427 0.75,0.604 0.281,0.177 10 false *1
*1 O-ring


Remove the 2 O-rings from the fuel main valve assembly.