Home › Engine / Hybrid System › M20A-FKS (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › from 2021.02
RM33A0E _51 Engine / Hybrid System _098627 M20A-FKS ENGINE MECHANICAL _0463500 REAR CRANKSHAFT OIL SEAL A

M20A-FKS ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear crankshaft oil seal removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Smart Entry and Start System

*2: w/o Smart Entry and Start System

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method
·

Gas leak from exhaust system is repaired

·

Replacement of air fuel ratio sensor (sensor 2)


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of continuously variable transaxle assembly
·

Input transaxle compensation code into TCM

·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for Initialization
(Click here)
for Registration
Replacement of ECM
·

Perform reset memory

·

Perform road test to allow TCM to learn


Replacement of ECM*1 Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method
Replacement of ECM*2 Perform code registration (Immobiliser system)
·

Wireless Door Lock Control System

·

Engine start


See Service Bulletin for the registration method
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Replacement of front bumper assembly Front television camera view adjustment Panoramic view monitor system (Click here)
for Initialization
(Click here)
for Calibration
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
for Initialization
(Click here)
for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front wheel alignment adjustment
·

Perform "Reset Memory"

·

Perform acceleration sensor zero point calibration and system information memorization


·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)
Replacement of front bumper assembly
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 32101 2.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly level.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.
A426058N05
0.99,0.75 0.99,1.333 0.99,1.333 1.406,1.333 false 0.677,0.75 1.177,0.75 false 0.354,0.677 0.813,0.875 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


c.
A400433

Remove the 8 bolts, rear drive plate spacer, drive plate and ring gear sub-assembly.


Hide 19315 3.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A426060

Remove the No. 1 crankshaft position sensor plate.


Hide 11401L 4.REMOVE REAR ENGINE OIL SEAL

a.
A426061C02
2.99,1.458 3.177,0.771 true 1.625,1.615 1.354,1.292 true 2.917,1.49 3.229,1.688 0.313,0.198 10 false *b 1.646,1.531 1.865,1.729 0.219,0.198 10 true *a
*a Protective Tape
*b Cut Position


Using a knife, cut off the lip of the rear engine oil seal.


b.

Using a screwdriver, pry out the rear engine oil seal.

NOTICE:

Do not damage the surface of the rear engine oil seal press fit hole or the crankshaft.


HINT:

Tape the screwdriver tip before use.