Home › Drivetrain › K120 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY › from 2021.02
RM33A0E _52 Drivetrain _098634 K120 CVT _0461775 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY A

K120 CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during continuously variable transaxle assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Not necessary when TCM replaced with new one

*2: The vehicle height changes because of suspension or tire replacement.

*3: w/ Smart Entry and Start System

*4: w/o Smart Entry and Start System

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of continuously variable transaxle assembly
·

Input transaxle compensation code into TCM

·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for Initialization
(Click here)
for Registration
Replacement of TCM
(If transaxle compensation code read from TCM)
·

Transfer transaxle compensation code

·

Perform reset memory*1

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


Replacement of TCM
(If transaxle compensation code not read from TCM)
·

Reset transaxle compensation code

·

Perform reset memory*1

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


Replacement of ECM
·

Perform reset memory

·

Perform road test to allow TCM to learn


Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Suspension, tires, etc.*2
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
for Initialization
(Click here)
for Calibration
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic view monitor system (Click here)
for Initialization
(Click here)
for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
Replacement of front bumper assembly
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front television camera view adjustment Panoramic view monitor system (Click here)
for Initialization
(Click here)
for Calibration
Replacement of ECM*3 Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method
Replacement of ECM*4 Perform code registration (Immobiliser function)
·

Wireless Door Lock Control System

·

Engine start


See Service Bulletin for the registration method
Front wheel alignment adjustment
·

Perform "Reset Memory"

·

Perform acceleration sensor zero point calibration and system information memorization


·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the transmission jack


Because the continuously variable transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the transmission jack could drop and components could fall down.



NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal.


PROCEDURE

Hide 1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 11361J 4.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
C413849C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and guide to remove the flywheel housing under cover from the cylinder block sub-assembly.


Hide 32101G 5.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
C413850

Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black colored drive plate and torque converter assembly setting bolt.



Hide 89535B 6.REMOVE TCM

NOTICE:

To prevent coolant from entering the TCM through its connector portion, be sure to remove the TCM before disconnecting any of the coolant system hoses.


a.
C447827

Remove the bolt to disconnect the engine wire from the No. 2 transmission control ECU bracket.


b.
C413834C01
0,0 0,0 false
V113147

Rotate in this Direction


Disengage the claw, rotate the lever and disconnect the TCM connector.


c.
C413832

Disengage the clamp.


d.
C413835

Remove the 2 bolts and TCM from the continuously variable transaxle assembly.


Hide 16264D 7.REMOVE FLOW SHUTTING VALVE (NO. 2 WATER BY-PASS HOSE) (for CVT)

Hide 16260 8.REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY) (for Heater)

Hide 16206 9.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

a.
C413851C01
0,0 0,0 false
V100135

Clip
V100136

Bolt


Slide the clip and disconnect the water by-pass pipe sub-assembly from the water by-pass outlet sub-assembly.


b.

Remove the 3 bolts and water by-pass pipe sub-assembly from the continuously variable transaxle assembly.


Hide 16261G 10.DISCONNECT NO. 1 WATER BY-PASS HOSE

Hide 11.DISCONNECT OIL COOLER HOSE

Hide 33493A 12.REMOVE TRANSMISSION OIL COOLER

Hide 45319 13.REMOVE STEERING GEAR HEAT INSULATOR

Hide 14.DISCONNECT ENGINE WIRE

a.
C441507

Disengage the clamp.


b.

Remove the bolt to disconnect the No. 2 engine wire from the wire harness clamp bracket.


c.
C413853

Remove the bolt and disengage the 3 clamps to disconnect the engine wire from the continuously variable transaxle assembly.


d.
C413854C01
2.271,1.698 2.448,1.885 0.177,0.188 10 true *a
*a Engine Coolant Temperature Sensor Connector


Remove the bolt and 2 nuts.


e.

Disconnect the engine coolant temperature sensor connector.


f.
C413855

Remove the bolt.


g.

Disengage the 2 clamps.


h.
C413856C01
0.302,3.125 0.51,3.302 0.208,0.177 10 true *a 1.125,2.073 1.302,2.24 0.177,0.167 10 true *b 2.094,3.24 2.271,3.417 0.177,0.177 10 true *c 2.521,2.344 2.698,2.51 0.177,0.167 10 true *d
*a Transmission Wire Connector
*b Shift Stroke Sensor Connector
*c Park/Neutral Position Switch Assembly Connector
*d Transmission Revolution Sensor (NOUT) Connector


Disengage the claw, rotate the lever and disconnect the transmission wire connector.


i.

Disconnect the shift stroke sensor connector.


j.

Disconnect the park/neutral position switch assembly connector.


k.

Disconnect the transmission revolution sensor (NOUT) connector.


l.
C426993C01
0.271,1.365 0.469,1.542 0.198,0.177 10 true *a 2.188,2.771 2.375,2.938 0.188,0.167 10 true *b
*a Transmission Revolution Sensor (NSS) Connector
*b Vacuum Hose


Disconnect the transmission revolution sensor (NSS) connector.


m.

Remove the bolt.


n.

Disconnect the vacuum hose.


o.
C441512C01
2.073,1.583 2.323,1.802 0.25,0.219 10 true *b 0.333,1.344 0.583,1.563 0.25,0.219 10 true *a
*a Transmission Revolution Sensor (NT) Connector
*b Oil Pressure Sensor Connector


Disconnect the transmission revolution sensor (NT) connector.


p.

Disconnect the oil pressure sensor connector.


q.

Disengage the clamp.


r.
C413859

Disengage the 3 clamps.


s.

Disconnect the rack and pinion power steering gear assembly connector.

C413860C01
4.271,0.417 4.583,0.573 0.313,0.156 10 false *a 0,0.156 0.156,0.313 0.156,0.156 10 false -
*a Rack and Pinion Power Steering Gear Assembly Connector - -


HINT:

Release the lock before rotating the lock lever.



t.

Remove the 2 bolts to disconnect the engine wire.


Hide 15.REMOVE FRONT FRAME ASSEMBLY

Hide 12311A 16.REMOVE FRONT ENGINE MOUNTING BRACKET

a.
C413861

Remove the 3 bolts and front engine mounting bracket from the continuously variable transaxle assembly.


Hide 11363A 17.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 19.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C413862

Remove the 2 bolts and wire harness clamp bracket from the continuously variable transaxle assembly.


Hide 20.REMOVE ENGINE ASSEMBLY

a.
C413863N01
0.906,0.167 1.063,0.365 0.156,0.198 10 false C 2.354,0.021 2.51,0.219 0.156,0.198 10 false A 2.771,0.24 2.927,0.438 0.156,0.198 10 false A 0.646,0.906 0.792,1.094 0.146,0.188 10 true C 0.875,1.635 1.021,1.823 0.146,0.188 10 true C 1.177,2.01 1.344,2.177 0.167,0.167 10 false C 2.448,2 2.604,2.177 0.156,0.177 10 true B 2.698,1.833 2.854,2.031 0.156,0.198 10 false C

Remove the 8 bolts and engine assembly from the continuously variable transaxle assembly.

NOTICE:

To prevent damage to the 2 knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.


HINT:
·

Bolt (A), (B): Remove from the continuously variable transaxle assembly side.

·

Bolt (C): Remove from the engine assembly side.




Hide 32000A 21.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C413864

Remove the torque converter assembly from the continuously variable transaxle assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.



Hide 22.REMOVE TRANSAXLE HOUSING TYPE T OIL SEAL

NOTICE:
·

Clean the work area, the tools to be used, and other equipment, etc. thoroughly before the operation, as there is the possibility that a CVT malfunction, which could prevent the vehicle from being able to be driven, could occur if dust or fine foreign matter enters the CVT.

·

Do not use cotton work gloves, cloths, or paper towels, etc. that may produce lint, dust or foreign matter.

·

Perform the operation as quickly as possible, as dust and foreign matter could enter the CVT while the torque converter assembly is removed.

·

Do not use an air gun until the torque converter assembly has been installed, as it could cause dust and foreign matter to be stirred up.



a.

Clean the tips of both the claws of SST and the center bolt.

SST
09308-10010  


b.
C398797E01
1.583,2.667 1.583,2.25 false 1.479,2.677 1.938,2.875 0.458,0.198 10 false SST

Using SST, remove the transaxle housing type T oil seal.

NOTICE:

Pay attention to the angle of the claws when opening them, and ensure that they do not come into contact with the transaxle housing, as there is the possibility that metal particles could be produced if they do.



Hide 82123 23.REMOVE NO. 3 ENGINE WIRE

a.
C413865

Disengage the clamp.


b.

Remove the bolt and No. 3 engine wire from the continuously variable transaxle assembly.


Hide 24.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C413866

Remove the 2 bolts and 2 wire harness clamp brackets.


b.
C413867

Remove the 2 bolts and 2 wire harness clamp brackets.


c.
C413868

Remove the bolt and wire harness clamp bracket.


Hide 33823 25.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C413869

Remove the 2 bolts and No. 1 transmission control cable bracket from the continuously variable transaxle assembly.


Hide 26.REMOVE BREATHER PLUG SUB-ASSEMBLY

HINT:

Perform this procedure only when replacement of the breather plug sub-assembly is necessary.


a.
C413870

Remove the breather plug sub-assembly from the continuously variable transaxle assembly.


b.
C398785C02
1.094,0.375 1.51,0.375 false 1.229,1.042 1.563,1.042 false 1.417,2.031 1.75,2.031 false 0.927,0.281 1.24,0.438 0.313,0.156 10 false *1 1.052,0.958 1.365,1.115 0.313,0.156 10 false *2 1.25,1.948 1.531,2.135 0.281,0.188 10 false *3
*1 Breather Plug Cap
*2 Breather Plug
*3 O-ring


Remove the breather plug cap from the breather plug.


c.

Remove the O-ring from the breather plug.


Hide 35150B 27.REMOVE TRANSMISSION CASE PLUG ASSEMBLY

a.
C413871C01
0.24,0.135 0.51,0.375 0.271,0.24 12 false *A 1.573,0.135 1.885,0.375 0.313,0.24 12 false *B
*A Type A
*B Type B


Remove the transmission case plug assembly from the continuously variable transaxle assembly.


b.

Remove the O-ring from the transmission case plug assembly.


Hide 16575F 28.REMOVE NO. 3 WATER HOSE CLAMP BRACKET

a.
C413872

Remove the 2 bolts and No. 3 water hose clamp bracket from the continuously variable transaxle assembly.


Hide 12303 30.REMOVE REAR ENGINE MOUNTING BRACKET SUB-ASSEMBLY

a.
C413873

Remove the 4 bolts and rear engine mounting bracket sub-assembly from the continuously variable transaxle assembly.


Hide 12304 31.REMOVE ENGINE MOUNTING BRACKET SUB-ASSEMBLY LH

a.
C413874

Remove the 5 bolts and engine mounting bracket sub-assembly LH from the continuously variable transaxle assembly.


Hide 32000A 32.INSPECT TORQUE CONVERTER ASSEMBLY

Hide 32101B 33.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY