Home › Engine / Hybrid System › M20A-FKS (INTAKE / EXHAUST) › INTAKE MANIFOLD › from 2021.02
RM33A0E _51 Engine / Hybrid System _099290 M20A-FKS INTAKE / EXHAUST _0463507 INTAKE MANIFOLD A

M20A-FKS INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during intake manifold removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 53295E 1.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 12601B 3.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 4.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 22030 5.SEPARATE THROTTLE BODY WITH MOTOR ASSEMBLY

a.
A433667

Disconnect the throttle body with motor assembly connector.


b.

Using an 8 mm socket wrench, remove the 3 bolts to separate the throttle body with motor assembly from the intake manifold.


Hide 22271 6.REMOVE THROTTLE BODY GASKET

Hide 25601 7.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 82121 8.DISCONNECT ENGINE WIRE

a.
A445056

Disconnect the 2 connectors.


b.

Remove the 2 bolts.


c.

Disengage the 2 wire harness clamps and disconnect the engine wire.


d.
A426162

Remove the bolt.


e.

Disengage the wire harness clamp and disconnect the engine wire.


Hide 16279 9.DISCONNECT NO. 3 WATER BY-PASS PIPE

a.
A433668

Using an 8 mm socket wrench, remove the bolt and disconnect the No. 3 water by-pass pipe from the intake manifold.


Hide 17138B 10.REMOVE INTAKE MANIFOLD STAY

a.
A426160N01
1.885,1.729 2.01,1.896 0.125,0.167 10 true B 1.302,1.625 1.427,1.792 0.125,0.167 10 true A

Using an 8 mm socket wrench, remove the bolt (A).


b.

Remove the bolt (B).


c.

Disengage the guide and remove the intake manifold stay.


Hide 23826 11.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A449056

Disconnect the No. 1 fuel vapor feed hose.


Hide 17111 12.REMOVE INTAKE MANIFOLD

a.
A426164

w/o Stud Bolt:

i.

Remove the 5 bolts and intake manifold from the cylinder head sub-assembly.



b.
A433670

w/ Stud Bolt:

i.

Remove the 3 bolts and 2 nuts.


ii.
A433671

Using an E8 "TORX" socket wrench, remove the 2 stud bolts and separate the intake manifold from the cylinder head sub-assembly.



Hide 17177 13.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

a.
A426165

Remove the No. 1 intake manifold to head gasket from the intake manifold.