Home › Engine / Hybrid System › M20A-FKS (INTAKE / EXHAUST) › EXHAUST MANIFOLD › from 2021.02
RM33A0E _51 Engine / Hybrid System _099290 M20A-FKS INTAKE / EXHAUST _0463508 EXHAUST MANIFOLD A

M20A-FKS INTAKE / EXHAUST  EXHAUST MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during exhaust manifold (TWC: Front Catalyst) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of air fuel ratio sensor (sensor 1)

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



PROCEDURE

Hide 57533B 1.REMOVE FRONT CENTER FLOOR BRACE

Hide 57523A 2.REMOVE CENTER FLOOR CROSSMEMBER BRACE

Hide 17410 3.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A402382

Disengage the wire harness clamp.


b.

Disconnect the air fuel ratio sensor (for sensor 2) connector.


c.
A402257

Remove the 2 bolts, 2 nuts and disconnect the front exhaust pipe assembly (TWC: Rear Catalyst) from the exhaust manifold (TWC: Front Catalyst) and center exhaust pipe assembly.


d.

Remove the front exhaust pipe assembly (TWC: Rear Catalyst) from the 2 exhaust pipe supports.


e.

Remove the 2 gaskets from the front exhaust pipe assembly (TWC: Rear Catalyst).


Hide 58152A 4.REMOVE FRONT LOWER NO. 1 FLOOR HEAT INSULATOR

Hide 53852K 5.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851Z 6.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 51441 7.REMOVE NO. 1 ENGINE UNDER COVER

Hide 55708 8.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53607A 9.REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY

Hide 89467B 10.REMOVE AIR FUEL RATIO SENSOR (for Sensor 1)

Hide 17167 11.SEPARATE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold (TWC: Front Catalyst) or other high temperature components while the engine is hot.


a.
A443148

Remove the 3 bolts and separate the No. 1 exhaust manifold heat insulator from the exhaust manifold (TWC: Front Catalyst).


Hide 58151 12.SEPARATE NO. 1 UPPER FRONT FLOOR HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A402261

Remove the 2 nuts and separate the No. 1 upper front floor heat insulator from the vehicle body.


Hide 17118 13.REMOVE MANIFOLD STAY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold (TWC: Front Catalyst) or other high temperature components while the engine is hot.


a.
A436580

Remove the bolt, nut and manifold stay from the exhaust manifold (TWC: Front Catalyst) and cylinder block sub-assembly.


Hide 17141 14.REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst)

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold (TWC: Front Catalyst) or other high temperature components while the engine is hot.


a.
A436581

Using a 12 mm deep socket wrench, remove the 7 nuts and separate the exhaust manifold (TWC: Front Catalyst) from the cylinder head sub-assembly.


b.

Remove the No. 1 exhaust manifold heat insulator, No. 1 upper front floor heat insulator and exhaust manifold (TWC: Front Catalyst).


c.
A426177

Remove the exhaust manifold to head gasket from the cylinder head sub-assembly.


Hide 17168 15.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A436582

Remove the 3 bolts and No. 2 exhaust manifold heat insulator from the exhaust manifold (TWC: Front Catalyst).