Home › Engine / Hybrid System › M20A-FKS (INTAKE / EXHAUST) › EXHAUST MANIFOLD › from 2021.02
RM33A0E _51 Engine / Hybrid System _099290 M20A-FKS INTAKE / EXHAUST _0463508 EXHAUST MANIFOLD A

M20A-FKS INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17168 1.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 2 exhaust manifold heat insulator to the exhaust manifold (TWC: Front Catalyst) with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17141 2.INSTALL EXHAUST MANIFOLD (TWC: Front Catalyst)

a.

Install a new exhaust manifold to head gasket to the cylinder head sub-assembly.


b.

Temporarily install the exhaust manifold (TWC: Front Catalyst), No. 1 upper front floor heat insulator and No. 1 exhaust manifold heat insulator.

HINT:

At this time, do not install the parts with bolts or nuts.



c.
A436581N01
1.615,1.083 1.771,1.281 0.156,0.198 10 true 1 0.958,0.042 1.115,0.24 0.156,0.198 10 true 2 2.542,0.052 2.698,0.25 0.156,0.198 10 true 3 1.26,1.063 1.417,1.26 0.156,0.198 10 true 4 2.875,0.854 3.031,1.052 0.156,0.198 10 true 5 0.531,0.99 0.688,1.188 0.156,0.198 10 true 6 0.219,0.083 0.375,0.281 0.156,0.198 10 true 7

Using a 12 mm deep socket wrench, temporarily install the exhaust manifold (TWC: Front Catalyst) to the cylinder head sub-assembly with 7 new nuts.


d.

Using the 12 mm deep socket wrench, tighten the 7 nuts in the order shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


Hide 17118 3.INSTALL MANIFOLD STAY

a.
A436580N01
3.031,1.385 3.188,1.583 0.156,0.198 10 true 1 0.833,1.406 0.99,1.604 0.156,0.198 10 true 2

Temporarily install the manifold stay to the exhaust manifold (TWC: Front Catalyst) and cylinder block sub-assembly with the bolt and nut.


b.

Tighten the bolt and nut in the order shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 58151 4.INSTALL NO. 1 UPPER FRONT FLOOR HEAT INSULATOR

a.
A402263C01
1.406,1.344 1.635,1.563 0.229,0.219 10 true *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, install the No. 1 upper front floor heat insulator to the vehicle body with the 2 nuts.

Torque:
Specified tightening torque : 4.9 N*m (50 kgf*cm, 43 in.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 4.3 N*m (44 kgf*cm, 38 in.*lbf)




Hide 17167 5.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold (TWC: Front Catalyst) with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 89467B 6.INSTALL AIR FUEL RATIO SENSOR (for Sensor 1)

Hide 53607A 7.INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY

Hide 55708 8.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 58152A 9.INSTALL FRONT LOWER NO. 1 FLOOR HEAT INSULATOR

Hide 17410 10.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

a.

Install 2 new gaskets to the front exhaust pipe assembly (TWC: Rear Catalyst).


b.

Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the 2 exhaust pipe supports.


c.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold (TWC: Front Catalyst) and center exhaust pipe assembly with 2 new bolts and 2 new nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


d.

Connect the air fuel ratio sensor (for sensor 2) connector.


e.

Engage the wire harness clamp.


Hide 57523A 11.INSTALL CENTER FLOOR CROSSMEMBER BRACE

Hide 57533B 12.INSTALL FRONT CENTER FLOOR BRACE

Hide 51441 14.INSTALL NO. 1 ENGINE UNDER COVER

Hide 53852K 15.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851Z 16.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH