Home › Engine / Hybrid System › CRUISE CONTROL › FRONT RADAR SENSOR SYSTEM › from 2021.02
RM33A0E _51 Engine / Hybrid System _065357 CRUISE CONTROL _0463557 FRONT RADAR SENSOR SYSTEM C

CRUISE CONTROL  FRONT RADAR SENSOR SYSTEM  U010487  Lost Communication with Cruise Control Module Missing Message  


DESCRIPTION

The millimeter wave radar sensor assembly communicates with the forward recognition camera via CAN communication.

If a communication error is detected between the forward recognition camera and millimeter wave radar sensor assembly, the millimeter wave radar sensor assembly stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
U010487 Lost Communication with Cruise Control Module Missing Message
Detection condition:

Ignition switch ON


Malfunction status:

Communication malfunction with the forward recognition camera is detected


Malfunction duration:

10 seconds or more


·

Pre-collision system

·

Forward recognition camera

·

Millimeter wave radar sensor assembly



Pattern DTC output part name
(Display on GTS)
Suspected Area (Malfunction Status)
Millimeter Wave Radar Sensor Assembly Forward Recognition Camera
Front Radar Sensor Pre-Collision System Lane Control Forward Recognition Camera (Front Lighting Control) Radar Cruise2
U010487 U023587 U023587 U023587 U023587

○: DTC is output

-: DTC is not output

Pattern 1 ○ ○ ○ ○ ○ Harness or connector (Open or short)
Millimeter wave radar sensor assembly (Internal malfunction)
Forward recognition camera (Internal malfunction)
Pattern 2 ○ - - - - Forward recognition camera (Internal malfunction)
Millimeter wave radar sensor assembly (Internal malfunction)

HINT:

If the DTCs are output simultaneously, the inspection area can be narrowed down.


WIRING DIAGRAM

B330403E95
0.75,1.875 2.729,2.073 1.979,0.198 10 false Forward Recognition Camera 4.823,1.854 6.24,2.281 1.417,0.427 10 false Millimeter Wave Radar Sensor Assembly 0.75,1.688 1.875,1.896 1.125,0.208 10 false V6*1, V25*2 4.823,1.688 5.135,1.885 0.313,0.198 10 false A30 1.604,0.792 2.219,0.99 0.615,0.198 10 false CANH 1.615,1.469 2.229,1.667 0.615,0.198 10 false CANL 5.115,0.771 5.729,0.969 0.615,0.198 10 false CA1P 5.125,1.479 5.74,1.677 0.615,0.198 10 false CA1N 2.083,0.781 2.24,0.979 0.156,0.198 10 false 6 2.073,1.25 2.271,1.448 0.198,0.198 10 false 12 4.948,0.771 5.104,0.969 0.156,0.198 10 false 5 4.948,1.24 5.104,1.438 0.156,0.198 10 false 6 0.167,2.24 4.906,2.438 4.74,0.198 10 false *1: Before Jan. 2022 Production 0.167,2.479 4.906,2.677 4.74,0.198 10 false *2: From Jan. 2022 Production

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.

·

When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history. Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.

HINT:

Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.

Triangle Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)

Flat Surface Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT


·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT




PROCEDURE

1.CHECK FOR DTCs
a.

Read each DTC and check the diagnosis pattern using the table below.

Body Electrical > Front Radar Sensor > Trouble Codes
50001 429
Body Electrical > Pre-Collision System > Trouble Codes
50001 432
Chassis > Lane Control > Trouble Codes
50001 418
Body Electrical > Front Recognition Camera (Front Lighting Control) > Trouble Codes
50001 433
Powertrain > Radar Cruise2 > Trouble Codes
50001 426
Pattern DTC output part name
(Display on GTS)
Front Radar Sensor Pre-Collision System Lane Control Forward Recognition Camera (Front Lighting Control) Radar Cruise2
Pattern 1 U010487 U023587 U023587 U023587 U023587
Pattern 2 U010487 - - - -


Result:
Result Proceed to
Pattern 1 A
Pattern 2 B



A

B

2.CHECK FORWARD RECOGNITION CAMERA
2.CHECK FORWARD RECOGNITION CAMERA
C426618C21
0.313,0.979 0.688,1.26 0.375,0.281 0.844,1.688 0.958,1.688 0.958,1.688 1.427,1.229 true 1.01,1.917 1.125,1.917 1.125,1.917 1.604,1.24 true 0.385,1.042 0.719,1.25 0.333,0.208 10 false A30 0.469,1.615 1.021,1.833 0.552,0.219 10 false CA1P 0.625,1.865 1.177,2.083 0.552,0.219 10 false CA1N 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


a.

Disconnect the millimeter wave radar sensor assembly connector.


b.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
A30-5 (CA1P) - A30-6 (CA1N) Ignition switch ON 1V/DIV., 100μs./DIV. Pulse generation



Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPLACE FORWARD RECOGNITION CAMERA